What causes a hole in the top of a 2005 Mustang?
What causes a hole in the top of a 2005 Mustang?
Some 2005-2007 Mustang vehicles built before 10/11/2006 and equipped with a convertible top could develop wear or a hole near the 4th bow and/or number 1 bow area. This is caused by the number 1 and number 4 bow wearing oe pinching through the vinyl or cloth top.
What’s the problem with my 2005 Mustang TSB?
MERCON® Automatic Transmission Fluid is being replaced by MERCON® V as a service fluid for power steering systems originally requiring MERCON®. Some 2005-2006 Mustangs may have a malfunction indicator lamp (MIL) on with diagnostic trouble code (DTC) P0456. This concern can be caused by an oversized orifice in the fuel pump.
Are there any recalls on the Mustang GT?
Some 2005-2006 Mustang GT vehicles may exhibit the malfunction indicator lamp (MIL) on, with diagnostic trouble codes (DTCs) P2004 through P2008, P151A, P2015, and P2020. All of these codes are associated with the charge motion control valve (CMCV), actuator motor, and/or linkage concerns.
What kind of engine does a 2005 Mustang have?
Some 2005 Mustang vehicles equipped with a 4.0L V6 engine and automatic transmission may exhibit an exhaust vibration or resonance at approximately 850 RPM. Ford Motor Company has adopted a new premium interior paint formulation that has significantly improved performance properties.
Some 2005-2007 Mustang vehicles built before 10/11/2006 and equipped with a convertible top could develop wear or a hole near the 4th bow and/or number 1 bow area. This is caused by the number 1 and number 4 bow wearing oe pinching through the vinyl or cloth top.
How do you replace the thermostat on a Ford Mustang?
Replace the thermostat cover and tighten down the three bolts securely. Reconnect the upper radiator hose and tighten the hose clamp back down if you don’t have the squeeze-type of connector. Be sure to tighten the hose on the radiator itself if you loosened it there.
How to remove transmission extension housing in Ford?
The which case you’ll just have to support the trans during your repair. It’s best to use a press to install the new one. Test fit it over the driveshaft before you bolt it back together. Good luck. drain pan under it , take it off . .. to any incidents . Give the rear end yoke a couple of good yanks too .
Is the seat cushion cover loose on a 2005 Mustang?
Some 2005 Mustangs built before 05/10/2005 may exhibit the seat cushion cover front trim being loose on the front seat. The J-clip that holds the seat cushion cover trim to the front of the seat pan (frame) may not be fully engaging the flanges (slots) in the seat frame (pan).
The which case you’ll just have to support the trans during your repair. It’s best to use a press to install the new one. Test fit it over the driveshaft before you bolt it back together. Good luck. drain pan under it , take it off . .. to any incidents . Give the rear end yoke a couple of good yanks too .
Replace the thermostat cover and tighten down the three bolts securely. Reconnect the upper radiator hose and tighten the hose clamp back down if you don’t have the squeeze-type of connector. Be sure to tighten the hose on the radiator itself if you loosened it there.
How to remove transmission housing from Ford E250?
Test fit it over the driveshaft before you bolt it back together. Good luck. drain pan under it , take it off . .. to any incidents . Give the rear end yoke a couple of good yanks too . end scream . Haven’t seen very many bushings go south and if it has,something is making that happen . > Ford E250 4.9L L6.
Can you tap out the bushing on a Ford?
In the Ford bushing drivers that allow you to tap out the old bushing. This requires described in any of the 3 manuals I have. Will I have to remove the entire transmission?
