Is there a problem with the Chrysler 300?

2008 LX 2.7L Chrysler 300 that will have hard shifts when driving over 40mph. Surging during shifting and when braking. Dealer has examined the vehicle and claims that there is no problem, advises use of higher grade gasoline to solve problem (that, according to the dealership, does not exist).

What happens when you program a new Chrysler key?

Back to top A few tips before you start the process of programming a new car key for Chrysler models: A. Once you program a new key, ALL previous keys will be erased and won’t start the car. In other words, if you find your old key after programming the new one, it will not work.

How much does it cost to diag a Chrysler 300?

Will go after the PCM/TCM software update. 3.5L V6, auto. Trans shop diag it as torque converter clutch. est $890.00. Dealer stepped up and diag it as trans. Replaced it and reprogrammed PCM/TCM and did a relearn all for free. All is well. Chrysler sales managers can get stuff done.

Why is my key fob not detected on my car?

In order to unlock the car, I would have to press the unlock button on the fob about 30 times before it finally worked. When I would try to start the car, I would always get the ‘Key Fob Not Detected’ message. The only way I could start the car was with direct contact between the key and ignition button.

Why are my key fobs not working on my Chrysler 300?

Both fobs wont start car. Lights come on trunk opens but not with either fobs. Dealer said they are in contact with Chrysler for a fix. NOTE, the day prior wife and I did smell electrical burn for few seconds inside car while driving and put it of as may have been another car on the road.

Why does my 2015 Chrysler 200 not start?

Key fob not detected. | Chrysler 200 Forum 2015 200s won’t start. Key fob not detected. I just got my 2015 200s a month ago and a few weeks ago the car would not start. The dash says key fob not detected. The lights and music turn on but will not start when I push the start/stop button.

Why is my car key not detecting my Charger?

The only way I could start the car was with direct contact between the key and ignition button. When I finally got around to bringing it to the dealership, they told me that there was an issue with the module in the car.

How long does it take for a software update on a Chrysler?

Note: The software update will take approximately 20 minutes depending on your region. Your Uconnect® system must maintain continuous power during the software update process. Therefore, the engine must be running while the vehicle is parked outside or in a well-ventilated area.

Why does my Chrysler Uconnect keep rebooting?

Sometimes the controls work, but the audio is missing. In February of 2018, FCA sent out an over-the-air software update that promptly caused thousands of units to endlessly reboot every 45 seconds or so. That didn’t go over well.

Is there a problem with my driveline vibration?

A number of problems can be associated with poor driveline performance, below we offer information on how to identify the problem and additional information on what may be causing the condition to help you in diagnose problems that fall into the following categories:

Why do I get a vibration when I press the accelerator?

If you lift your foot off the accelerator to maintain cruising speed, the vibration will disappear; if you press the accelerator in order to pass someone, the vibration will return. If you experience this type of vibration and your mechanic is scratching their head, I may have the solution for you.

What kind of vibration does a Dodge Ram have?

I have a 96 Dodge Ram 1500 extended cab which vibrates at the speed of 30 – 40 mph. The vibration is felt all over, steering wheel, seat, etc. There is no vibration at speeds below or above these speeds. I have had my tires balanced and partial alignment as I was told that the wheel bearing should be check as there is some play but not much.

Can a drive line out of balance cause a vibration?

Can that cause the vibration or can it be something else. Any advise would be appreciated. answer 96 dodge, YES IF A DRIVE LINE IS OUT OF BALANCE YES IT WOULD CAUSE A SHAKE.AND SENSE U HAD TIRES BALANCED THE ONLY THING LEFT WOULD BE DRIVE LINE HAVE IT BALANCED AND OR REPLACED.

Why does my Dodge Ram pulsate at 30 mph?

The right front wheel on my 97 4×4 starts to rumble at about 30 mph when it is in 2wd. When I put it in 4wd, it goes away. The bearing was replaced about 1000 miles ago and there is no side play when I jack it up, and when I spin the wheel, it starts to rumble and vibrate in the hub area.

How to troubleshoot a transmission shift solenoid problem?

Using a diagnostic scanner is a must when it comes to shift solenoid related problems. Here is a list of how you can carry out the troubleshooting with a scanner: Find a transmission wiring diagram for your transmission. Find out which pins are going to the affected shift solenoid.

What causes a CarGurus transmission to not shift?

– CarGurus electrical problem causing my transmission to not want to shift from 3rd gear to 4th gear.

Why is my Chrysler Town and Country not shifting?

No error codes but van will occasionally not shift and is stuck in lower gear. When this happens, turning the car off and then back on has always reset the issue and it drives normal. I assume it is electrical as fluid looks good.

Is there a problem with the Chrysler 300?