Is the ignition lock on a 1997 Chevy Blazer?

The ignition lock cylinder and ignition switch in your 1997 Chevrolet Blazer work together as a single assembly. Still, you can replace the faulty switch as a separate unit from its housing.

How do you replace the ignition switch on a car?

Make sure you have all the required tools to replace the switch before you start. Insert the ignition key into the lock cylinder and turn the key to the “On” position without starting the engine. Then align the front wheels so they point straight ahead. Turn the ignition switch off and remove the key from the lock cylinder.

How do you turn the ignition off on a Honda Accord?

Insert the ignition key into the lock cylinder and turn the key to the “On” position without starting the engine. Then align the front wheels so they point straight ahead. Turn the ignition switch off and remove the key from the lock cylinder. Disconnect the battery ground (black) cable with a wrench.

Where are the gears on an ignition switch?

Look at the gears on top of the old ignition switch. The gears on the new ignition switch should be in the same position before installation. Plug in the electrical connector to the new ignition switch and insert the switch into the cylinder housing until the switch tab snap into the slots of the lock cylinder housing.

The ignition lock cylinder and ignition switch in your 1997 Chevrolet Blazer work together as a single assembly. Still, you can replace the faulty switch as a separate unit from its housing.

How do you unlock an ignition lock cylinder?

First, insert the key and unlock the steering wheel. Next, use a flat blade screwdriver to press a small metal push pin that is located underneath the ignition lock cylinder. By depressing this switch, you’ll be able to unlock the cylinder from the housing.

What causes a fault in an ignition lock cylinder?

Most of the time, when a problem occurs within the ignition system, it will be caused by a fault within the ignition lock cylinder. Inside the lock cylinder are a series of tumblers where the key is inserted.

Why is my ignition lock cylinder not working?

The ignition lock cylinder is connected to an electronic ignition switch, they work power on and start the vehicle. If the ignition lock cylinder wear out or breaks, it may prevent the vehicle from starting when the key is inserted and turned. A no start condition can also be caused by a wide variety of other issues,…

What’s the name of the ignition lock cylinder?

The ignition lock cylinder is the cylindrical tumbler and key that is used to power on and start the vehicle. While many newer vehicles are now being manufactured with push button and keyless power and starting systems, traditional ignition lock cylinders are still commonly found on many road…

How to fix ignition problems by replacing the ignition switch?

How to fix ignition problems by replacing the ignition switch. Ignition switch location, inspection, removal and repair. DIY car repair with Scotty Kilmer, an auto mechanic for the last 43 years. 1. Screwdriver set: http://amzn.to/2j92UCG 2. Disposable Gloves: http://amzn.to/2zSRuxO 3. Common Sense 4. Full HD Camera: http://amzn.to/2AvoEk7 5.

Where is the release pin on an ignition switch?

The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.

Can a faulty ignition switch cause a car to stall?

A faulty ignition switch in your vehicle can cause several problems ranging from your car stalling and all lights going dark to the radio not working unless the key is wiggled from side to side. Once you’ve been able to identify the ignition switch as the source of your trouble,…

Can you replace the ignition switch on a trailblazer?

Easy way to replace the Ignition Switch in Trailblazer 2002. – YouTube Easy way to replace the Ignition Switch in Trailblazer 2002. If playback doesn’t begin shortly, try restarting your device.

What happens if you have a faulty ignition switch?

A faulty ignition switch in your vehicle can cause several problems ranging from your car stalling and all lights going dark to the radio not working unless the key is wiggled from side to side.

Why is my ignition switch not working properly?

If the contacts inside of the switch fail, they will not make proper contact, which will cause open circuits in the switch. Symptom 3: Electrical malfunctions. Since your ignition switch is responsible for the on and off toggle for most of the electrical circuits in your vehicle, it can cause a series of electrical problems.

Where is the ignition switch on a 1997 GMC?

Disconnect the ignition switch from the vehicle wiring harness connector at the base of the steering column. Place your multimeter in Ohms mode. Place the ignition key in the ACC position. You should have continuity between terminals D2 and D6 of the ignition switch connector.

What kind of ignition switch does a 1997 Chevy Tahoe have?

This tutorial will help you test the ignition switch on the 1997 Chevrolet and GMC Pick Up, Suburban, Tahoe, and Yukon equipped with a 4.3L, 5.0L, or a 5.8L V8 engine. The ignition switch test involves checking for continuity across specific terminals of the ignition switches connector.

What causes the tumbler Assembly on a ignition switch to jam?

Step 4 – Dirt and debris inside the key lock can cause the tumbler assembly to stick and jam, not allowing one or more of the key followers to operate.

Can a unworn key turn an ignition cylinder?

Or, an unworn key may not turn a worn ignition cylinder, as they haven’t “worn together.” How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders.

What to do if your ignition switch won’t work?

Step 7 – In extreme conditions such as high mileage or a key chain adorned with many ornaments can wear the tumbler which causes the key not to work. If the door key is same as the ignition key, the door tumbler can be removed and a key made if no security chip is installed, (older cars).

How is the ignition switch connected to the trunk?

You might consider getting a matched lockset that includes the door and trunk cylinders. The ignition switch itself is connected to the ignition cylinder by a shaft or lever. Inside the ignition switch, several contacts connect vital electrical systems needed to start and run the car.

What does it mean when your key is stuck in the ignition?

Key is stuck in the ignition and won’t turn all the way b… My key has been stuck in the ignition for a few weeks now and it’s still been cranking up until yesterday. Turn the key and nothing. From what I’ve read it could be the ignition switch gone bad but I just noticed also that the gear shift does not totally lock into park.

What should I do if my ignition switch is not working?

How To Fix It: After ensuring the rest of the electrical system is intact, such as fuses, relays, and circuits, replace the ignition switch. The transponder antenna surrounds the ignition cylinder. If it doesn’t recognize the transponder key, it doesn’t allow the engine to run. https://www.gettyimages.com/license/525320791

What happens if you break the ignition lock?

The key slides into the ignition lock cylinder. These two components mate together and essentially become one. So if either of them break, they will both be affected. In addition, there are many other small moving parts inside your steering column that are activated when you insert the key and turn it.

Why is my car not turning on when I Turn on the ignition?

Of course, if you access the car itself with your key, you likely won’t be able to turn on the ignition because of all those extra tumblers. And on the off chance that you do turn the ignition cylinder, the immobilizer won’t allow you to start the car, because it’s protected by one-in-millions of transponder codes.

Is there a replacement key for a Chevy Blazer?

There are, however, two things to consider: For Chevrolet Blazer vehicles that are older than ten years, there are no codes available. So, an automotive locksmith is your only option to get a replacement key. For Chevrolet Blazer vehicles equipped with a transponder system and/or remote, intelligent key, or fob key, codes are available.

How do you install a new lock cylinder?

Insert the new lock cylinder and move the retaining clip back into place to secure the cylinder. Ensure that all washers and gaskets are installed in the correct order. If installing the cylinder into the handle housing unit, reinstall the unit into the tailgate and secure the handleâ€™s retaining bolts and linkages. Step 4: Test the lock cylinder.

When did the Chevy Blazer first come out?

Chevrolet Blazer was introduced in 1969. This model has two versions and five types of keys. Non Transponder Key: 1991-2006 – Four types of keys. Remote Key Fob: 2019-2020 – One type of remote.

Do you need a transponder for a Chevy Blazer?

To make things simple, we divided all Chevrolet Blazer keys into two categories: No programming needed (Non-transponder keys). Keys that needs to be programmed (Transponder or remote keys). These keys required the expertise of an automotive locksmith or the dealer.

Do you have to take steering wheel out to replace ignition switch?

Take the steering wheel out if it’s in the way. In some vehicles, you may be able to replace the ignition switch without removing the steering wheel. However, if you’re unable to get access to the top of the ignition switch with all the interior trim pieces removed, the steering wheel may need to come out.

What should I do if I need to replace my ignition switch?

Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.

What’s the Accessory position on an ignition switch?

Insert the key and turn it to the “accessory” position. The ignition switch needs to be set to the accessory position before you can release it from the ignition module. The “accessory” position is before the starter is engaged, and would normally let you run the vehicle’s electronics without the engine running (when the battery is connected).

How do you remove a battery from an ignition switch?

Use an appropriate sized wrench to loosen the nut holding the cable on the negative (-) terminal and then slide it off the post. You don’t need to remove the positive cable from its terminal. Tuck the negative cable to the side of the battery to make sure it doesn’t accidentally come into contact with the terminals.

Where does the wire go on an ignition switch?

Connect the ignition wire to the “IGN” terminal of the ignition switch. This is the main terminal that is used for vehicle ignition, wipers, accessories and other operating features. This is the normal “run” position of the switch. Reconnect the cable to the negative battery terminal.

How do you unplug an ignition switch on a car?

Unplug the two electrical connectors from the lock cylinder housing. Push the ignition switch tabs through the two slots at the bottom of the lock cylinder housing with special tool J-42759, pull the ignition switch out of the lock cylinder housing, and unplug the switch electrical connector. Look at the gears on top of the old ignition switch.

What can cause an ignition switch to fail?

(These generalizations, depend significantly on year, make, and model.) Worn ignition switch contacts, temperature problems, or broken springs can all cause the ignition switch to fail, preventing you from starting your car. On the road, poor ignition switch contacts could shut the engine off while driving, which could be dangerous.

Is the ignition lock on a 1997 Chevy Blazer?