How to replace front wheel bearing on Chevy Silverado?
How to replace front wheel bearing on Chevy Silverado?
Learn how to replace the wheel bearing hub assembly on almost any truck or car. This is a 2004 Chevy Silverado, GMC Sierra but the process will be very similar for replacing any wheel bearing hub assembly with an axle running through it. I was able to purchase a new hub assembly from AutoZone for $120. Duralast Wheel Bearing/Hub Assembly-Frnt.
Why are the wheels spinning on my Chevy Silverado?
The wheels spin freely like the front differential is not engaged. Like I said, I replaced the front axle actuator, pulled it off again and it goes in and out, put it back on and still no locking of the diff? Kind of stumped, might take it to a mechanic.
How to replace the lower wheel knuckle on a Chevy Silverado?
Lift lower control arm to free the knuckle from the ball joint’s threaded stud. While lifting up the wheel knuckle, lower the jack, and then pull the wheel knuckle out and away from the lower control arm. Figure 21. Pull away detached wheel knuckle from the lower control arm.
Where to remove lower control arm nut on Chevy Silverado?
Remove the already-loosened 24mm nut at the bottom of the wheel knuckle. This nut holds the lower control arm ball joint to the knuckle via its threaded stud. With the jack still in place, remove the 35mm wheel nut and the washer behind it from the center of the hub.
The wheels spin freely like the front differential is not engaged. Like I said, I replaced the front axle actuator, pulled it off again and it goes in and out, put it back on and still no locking of the diff? Kind of stumped, might take it to a mechanic.
Why does my GMC 2500 front axle not engage?
I have recently purchased a 2000 GMC 2500. Today we got a lot of snow so i went to put it into 4×4 and the front axle did not engage. The transfer case is working and engaged with the front axle spinning as it should. Any idea on what the problem could be or where to start looking? Thanks.
What to do when front axle does not engage in 4×4?
You say the front driveshaft is turning and the transfer case is definatly engaging? does it make any noise when you hit 4×4 hi or lo leave the engine off put it in neutral and listen for anything. in the front. its really quite so make sure radio and all that is off.
Where is the wheel hub on a Chevy Silverado?
This article applies to the Chevrolet Silverado 1500 (2007-2013). Unless you’ve replaced a wheel hub bearing yourself, chances are you’ve never actually seen one. The wheel hub bearing is buried deep inside the wheel assembly of your Silverado, and it plays a big role in safety, but primarily handling and road-worthiness.
When to replace the spindle on a Chevy Silverado?
But even parts designed for this kind of job eventually wear out. Keep in mind that in the Silverado, the bearing is sealed in the spindle assembly, and the whole part may be replaced. Once the lubricant wears out due to mileage or abuse, they can start grinding and vibrating.
Can a Chevy Silverado wheel be replaced at any time?
Bearings allow other parts spin or rotate freely, so enduring large amounts of friction and heat is part of their job. But even parts designed for this kind of job eventually wear out. Keep in mind that in the Silverado, the bearing is sealed in the spindle assembly, and the whole part may be replaced.
Do you need to replace wheel bearings on a Chevy Silverado?
Replacing the wheel bearings is a bit of a tedious process, but definitely important for the well being of your truck. This article applies to the Chevrolet Silverado 1500 (2007-2013). Unless you’ve replaced a wheel hub bearing yourself, chances are you’ve never actually seen one.
Where is the hub bearing on a Chevy Silverado?
Unless you’ve replaced a wheel hub bearing yourself, chances are you’ve never actually seen one. The wheel hub bearing is buried deep inside the wheel assembly of your Silverado, and it plays a big role in safety, but primarily handling and road-worthiness.
How do you replace the front wheel on a Chevy Silverado?
Once the lubricant wears out due to mileage or abuse, they can start grinding and vibrating. Start by using the lug nut wrench to partially loosen the lug nuts, then find the appropriate jacking spot for your truck, and jack it up using the floor jack.
But even parts designed for this kind of job eventually wear out. Keep in mind that in the Silverado, the bearing is sealed in the spindle assembly, and the whole part may be replaced. Once the lubricant wears out due to mileage or abuse, they can start grinding and vibrating.
Why do I need to replace my front wheel bearings?
Wheel bearings allow your wheel to rotate with minimum friction as well as support the weight of the vehicle on that corner, which means even the slightest bit of damage can lead to problems. The first problem you’ll begin to notice is that the alignment will feel like it’s out. In addition, the front tires will begin to wear unevenly.
What happens if you lose a wheel on a Chevy Silverado?
Excessive driving on failed bearings can cause two major problems: the friction can cause the bearing to weld itself in place which can lead to it shearing off the hub and you can potentially lose a wheel going down the highway. Park on flat, level ground. Chock the wheels on the opposite end of the truck that you are removing the wheel from.
Can a bad wheel bearings cause tires to wear irregularly?
Bad wheels bearings can cause your tires to wear irregularly. Prevent this by replacing the bearings; learn how to here. This article applies to the Chevrolet Silverado 1500 (1996-2006).
Learn how to replace the wheel bearing hub assembly on almost any truck or car. This is a 2004 Chevy Silverado, GMC Sierra but the process will be very similar for replacing any wheel bearing hub assembly with an axle running through it. I was able to purchase a new hub assembly from AutoZone for $120. Duralast Wheel Bearing/Hub Assembly-Frnt.
Wheel bearings allow your wheel to rotate with minimum friction as well as support the weight of the vehicle on that corner, which means even the slightest bit of damage can lead to problems. The first problem you’ll begin to notice is that the alignment will feel like it’s out. In addition, the front tires will begin to wear unevenly.
Excessive driving on failed bearings can cause two major problems: the friction can cause the bearing to weld itself in place which can lead to it shearing off the hub and you can potentially lose a wheel going down the highway. Park on flat, level ground. Chock the wheels on the opposite end of the truck that you are removing the wheel from.
Bad wheels bearings can cause your tires to wear irregularly. Prevent this by replacing the bearings; learn how to here. This article applies to the Chevrolet Silverado 1500 (1996-2006).
How do you remove a wheel from a Chevy Silverado?
Chock the wheels on the opposite end of the truck that you are removing the wheel from. Using the tire iron, loosen the lug nuts on the wheel. Raise the vehicle using the floor jack high enough to get the wheel off. Position the jack stand under the lower control arm. Finish removing the lug nuts and then remove the wheel.
How do you install a new hub assembly?
Push the new hub assembly onto the center stud. Re-install the three 15mm bolts on the back of the assembly to attach it to the knuckle. Be sure to tighten evenly. If you have a torque wrench, you’ll need to torque these to 75 ft-lbs.
How do you jack up a Chevy Silverado?
Using the tire iron, loosen the lug nuts on the wheel. Raise the vehicle using the floor jack high enough to get the wheel off. Position the jack stand under the lower control arm. Finish removing the lug nuts and then remove the wheel. Lower the truck onto the jack stand. (Related Article: How to Jack Up Your Truck – ChevroletForum.com) Figure 1.
Chock the wheels on the opposite end of the truck that you are removing the wheel from. Using the tire iron, loosen the lug nuts on the wheel. Raise the vehicle using the floor jack high enough to get the wheel off. Position the jack stand under the lower control arm. Finish removing the lug nuts and then remove the wheel.
What to do if your wheel hub assembly is broken?
However, if one side wheel hub assembly is broken, both sides on the same axle need to be replaced at the same time. If you notice any roaring or grinding sound coming from the front end of your vehicle, safely drive home and contact a local ASE certified mechanic as soon as possible.
What kind of hub assembly does a car have?
Today’s modern cars, and those manufactured after 1997 are equipped with a single bearing and hub assembly that is attached to each wheel and tire on a vehicle.
How do you replace the front axle on a Chevy Silverado?
You are hammering the spindle to break the splines of the shaft loose from the hub. There are six 15mm bolts on the axle flange at the differential. Since your truck is jacked up, when applying rotational force to the heads of the bolts, the wheel will be able to spin freely on its axis.
Push the new hub assembly onto the center stud. Re-install the three 15mm bolts on the back of the assembly to attach it to the knuckle. Be sure to tighten evenly. If you have a torque wrench, you’ll need to torque these to 75 ft-lbs.
Using the tire iron, loosen the lug nuts on the wheel. Raise the vehicle using the floor jack high enough to get the wheel off. Position the jack stand under the lower control arm. Finish removing the lug nuts and then remove the wheel. Lower the truck onto the jack stand. (Related Article: How to Jack Up Your Truck – ChevroletForum.com) Figure 1.
