Easy lifehacks

How to remove the lower spare tire from a trailblazer?

How to remove the lower spare tire from a trailblazer?

Continue to turn the wrench until the cable lowers to the ground and has enough slack to lift the spare tire up and remove the center the center mounting bracket from the hub of the spare tire. Angle the mounting bracket (attached to the cable) sideways to fit it through the hub of the spare tire. Roadside emergency kit (equipped with vehicle)

Who is the owner of the Chevrolet TrailBlazer?

The names, logos, emblems, slogans, vehicle model names, and vehicle body designs appearing in this manual including, but not limited to, GM, the GM logo, CHEVROLET, the CHEVROLET Emblem, and TRAILBLAZER are trademarks and/or service marks of General Motors LLC, its subsidiaries, affiliates, or licensors.

What should I know about driving a trailblazer?

About Driving the Vehicle As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or a crash. Be sure to read the driving guidelines in this manual in the section called “Driving and Operating” and specificallyDriver Behavior0181,Driving Environment0181, andVehicle Design0181.

Where is the roadside emergency kit on a trailblazer?

Locate the roadside emergency kit on the TrailBlazer. On the shorter wheelbase models, the kit is located under the rear seat, and the longer wheelbase versions of the models stored the kit in the driver’s side rear quarter panel compartment. Raise the rear lift gate (on longer wheel base versions, this step would be performed to obtain the kit).

When did the Chevy Trailblazer come out in the US?

The Chevy TrailBlazer was first introduced in the United States in 2002. Although it shared a couple years of production with the S10 Blazer, the slightly larger TrailBlazer inevitably took the S10 Blazer’s place.

Continue to turn the wrench until the cable lowers to the ground and has enough slack to lift the spare tire up and remove the center the center mounting bracket from the hub of the spare tire. Angle the mounting bracket (attached to the cable) sideways to fit it through the hub of the spare tire. Roadside emergency kit (equipped with vehicle)

The Chevy TrailBlazer was first introduced in the United States in 2002. Although it shared a couple years of production with the S10 Blazer, the slightly larger TrailBlazer inevitably took the S10 Blazer’s place.

Locate the roadside emergency kit on the TrailBlazer. On the shorter wheelbase models, the kit is located under the rear seat, and the longer wheelbase versions of the models stored the kit in the driver’s side rear quarter panel compartment. Raise the rear lift gate (on longer wheel base versions, this step would be performed to obtain the kit).

How do you get a spare tire out of a Chevy truck?

This will turn the pully, and the spare tire will descend towards the ground. Continue rotating until the tire is firmly on the ground, and continue to rotate to give some slack to the wire. This step is to separate the pulley carrier from the rim, such that you can extract the tire from under the truck.

How do you mate a spare tire on a Chevy?

(If you look through the hole, you’ll see where the female end will match to the male end.) Insert the rod through the hole and mate up the male and female parts. Affix the crowbar to the remaining end sticking out of the bumper, and then rotate the crowbar counter-clockwise.

When to replace coolant hoses on a trailblazer?

Coolant hoses wear out over time and need to be replaced – check ’em early and often 2005 Chevrolet Trailblazer LS 4.2L 6 Cyl. Check power steering fluid level Power steering fluid is easy to check and many people (mechanics included) often forget about – learn how here 2005 Chevrolet Trailblazer LS 4.2L 6 Cyl.

How do you remove a spare tire from a Chevy Silverado?

At this point, the secondary latch is released and the spare tire is balancing securely and safely on the jack. Crank the wheel wrench in a counter-clockwise direction to lower the jack. Continue to do so until the spare tire either slides off the jack or hangs from the cable for easy removal. Figure 2. This is your spare wheel wrench.

How do you put a spare tire on a car?

Raise the jack by cranking the wheel wrench in a clockwise direction. Continue cranking the wheel wrench until the spare tire has no where else to go and is held firmly in place. At this point, the secondary latch is released and the spare tire is balancing securely and safely on the jack.

Where is the spare tire on a GMC Truck?

Insert the ignition key, and turn to the right while pulling a little towards you. The lock will separate from the hole, and just set the assembly in the back of the truck. Open the Tire Changing pouch to reveal the crowbar and the multiple rods.

Author Image
Ruth Doyle