How to check transaxle fluid in Chevy Malibu?

Adding Transaxle Fluid: With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole. 1. Install fluid level screw. Tighten 12 N.m (106 lb in) 2. Lower vehicle. Loading…

How can you tell if there is no dipstick in transmission fluid?

Check under the hood and look around carefully to confirm that there is no dipstick. The location of the transmission fluid dipstick varies greatly from one car model to the next, so it can be easy to miss if you’re not fully familiar with the vehicle in question.

Where is the transmission fluid check valve located?

The reason for this is that the transmission fluid check valve on a sealed transmission is on the bottom of the car, but the vehicle must also be level to ensure an accurate reading.

Where can I get a dip stick to check my fluid?

If you do not necessarily want to buy a dipstick, but you still want to check your fluid, see if you can make arrangements to drive to the dealership and use one of theirs. If you make it clear that all you want to do is borrow it for a minute to check your fluid level in their parking lot, they may allow you to do so.

How do I check the transmission fluid level?

Checking transmission fluid is simple if you follow a few rules. 1. Always check transmission fluid when the engine is warm 2. Always check transmission fluid when the engine is running 3. Only check transmission fluid when the vehicle is on Level ground 4. Only add the fluid a little at a time, maybe 1/2 pint until it reaches the line 5.

Where is the transmission dipstick on a Chevy Malibu?

The transmission dipstick on a Malibu 2008 is located towards the front of the engine on the right side (Drivers side) by the car battery; you won’t locate it right away because its view is blocked by the air intake hose, but it’s not hard to squeeze your hand to pull the dipstick without removing the air intake hose.

What should I do if my Trans fluid level is low?

If the fluid is low, it’s low, add some. If it’s too full, it’ll come out. If the trans is lacking a quart or more, not having the car perfectly level is less of an issue than adding some fluid so it can do its job.

How can I check the fluid level in my car?

You would be correct about the bolt on the side of the case to check the level. The car has to be level, running, and warm. A bit of a pain in the rear to do in the driveway. Don’t open it when the car isn’t running, or you will lose a good bit of fluid.

How many drain and fills does a Chevy Malibu need?

Numbers are rounded and based on draining 4.3 quarts, with a total system capacity of 9.5 quarts. As you can see there is a significant reduction in efficiency because you are losing 45% of the total amount of new fluid each time you drain it. So, in conclusion 3 or 4 drain and fills is whats needed to change most of the fluid.

What kind of transmission does a Chevy Malibu have?

For 2009, the 2.4L 4-cylinder and 3.5L V6 got the 4-speed transmission. The 3.6L V6 got the 6-speed. I forgot to add when I originally made this thread that this is for the 6T40 6 speed transmission paired with the 2.4L. and it does not have a removable pan.

What kind of fluid does a Chevrolet use?

Information about type and capacity fluid are for reference only. Reference book «Fluid type : automatic transmission Chevrolet». Full capacity l. Service fill l.

How to check the transmission fluid level in a Chevy Aveo?

Transmission Fluid Level Check Chevrolet Aveo (2004-2011) – 2009 Chevrolet Aveo LS 1.6L 4 Cyl. See how to correctly check the transmission fluid level in a 2009 Chevrolet Aveo LS 1.6L 4 Cyl.. The engine should be running when you check the transmission fluid dipstick on a 2009 Chevrolet Aveo LS 1.6L 4 Cyl. About Us Maintenance Parts & Tools Contact

How to check the transmission fluid in a Jeep Liberty?

1. Getting Started – Prepare for the repair 2. Open the Hood – How to pop the hood and prop it open 3. Remove Dipstick – Access point for transmission fluid 4. Check Level – Insert dipstick and pull it out to determine level 5. Add Fluid – Determine correct fluid type and add fluid

What happens when you check your transmission fluid?

If you check your fluid level when the transmission fluid is too cold, you will over fill it. Conversely, if you check the level when its too hot, you will under fill it. Less transmission fluid will cause damage and early wear.

What should the temperature of the transmission fluid be?

Whether you are an old wrench or a new owner, you should know how to check and diagnose your transmission fluid, so your transmission stays in tiptop shape for years to come. In order to properly and accurately check your transmission fluids, the transmission fluid temperature must be between 86 and 122 degrees Fahrenheit.