How many GMC trucks have throttle body injection?

New and Remanufactured Throttle Body Assemblies for 305, 350, 454 Chevy, GM, GMC Trucks, Cars, Vans and 6 Liter and 7 Liter Trucks. Serving our valued customers for over 30 years.

How long does it take for GM throttle body to relearn?

If you don’t do a relearn procedure, the PCM will “hunt” for a new baseline idle. It will eventually learn it on its own, but it may take over a week of driving, during which time you will experience high and low idle speeds and possibly rough idle. 1) Start the engine and let it idle in park for 3 minutes.

Is the General Motors Rochester throttle body OEM?

The General Motors Rochester Throttle Body (TBI) is OEM original equipment. Each TBI comes complete with injectors, TPS, air control valve, and throttle body bushings. Every TBI will be Flow Bench tested, calibrated, and idle adjusted making it ready for easy installation. Each TBI has a complete one year warranty.

How does idle air control work in a GM TBI?

The air gap between the throttle body and the throttle plate is calibrated to allow enough air to pass by it for the engine to run at base idle speed. The IAC (Idle Air Control) valve utilizes the on-board computer to fine tune the idle speed according to engine conditions.

New and Remanufactured Throttle Body Assemblies for 305, 350, 454 Chevy, GM, GMC Trucks, Cars, Vans and 6 Liter and 7 Liter Trucks. Serving our valued customers for over 30 years.

What was the throttle body on a 1994 Chevy CK?

Chevy CK Pickup 7.4L 1994, GM Original Equipment™ Throttle Body Idle Air Control Motor by ACDelco®. Bring your vehicle’s fuel system back to its top shape with this top-notch part.

What makes up the throttle body and idle air?

IAT – Intake Air Temperature – Measures the temperature of the air the engine is intaking. IAC – Idle air control – Controls the amount of air the engine is intaking while it is idling. Throttle body – Responsible for regulating flow of air into the engine as you press the gas pedal.

What was the year of the Chevy TBI throttle?

1987 1988 1989 CHEVY GMC TBI THROTTLE BODY TRUCK / SUBURBAN w/7.4L / 454c.i. V8. If you are not sure about your application please don’t hesitate to contact our sales/tech dept by emailing us and we will gladly help you.

What kind of gas mileage does a 454 TBI get?

GAS MILEAGE. Always a big complaint with 454 TBI trucks. 90 and older is particularly bad and that is largely due to NO OVERDRIVE. Nothing is going to help that fuel mileage more than overdrive.

How long is the warranty for throttle body injection?

All TBI’s, Throttle Body Assemblies, and Multi Port Injectors come with a Complete One Year Warranty. Each unit is completely Flow Bench Tested and ready for Easy Installation. Online purchase is quick, easy and secure because we are a PayPal Verified Merchant.

GAS MILEAGE. Always a big complaint with 454 TBI trucks. 90 and older is particularly bad and that is largely due to NO OVERDRIVE. Nothing is going to help that fuel mileage more than overdrive.

What’s the idle RPM on a 1992 Chevy 350 TBI?

I have a 1992 Chevrolet K2500 350 tbi that idles high about 1200 to 1500 rpm sometime’s will idle about 800 rpm. When i first start the truck it slowly rises from 1000 to 1500 rpm then comes down after five minutes to 1000 rpm then when i drive it for a few minutes then it starts idling at 1100 rpm when the truck is in drive.

Why does my GMC Truck die at idle?

Once the engine is warmed up then it relies on the O2 sensor for air/fuel ratio. A rough idle usually means a vacuum leak. I would check for those especially vacuum lines.

Can a bad throttle position sensor cause idle surging?

Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges. 3) Check Engine Light

Once the engine is warmed up then it relies on the O2 sensor for air/fuel ratio. A rough idle usually means a vacuum leak. I would check for those especially vacuum lines.

How is the throttle connected to the accelerator?

In the old days, there used to be a cable that was connected from the throttle to the accelerator. But now in the technological age, the car’s computer controls when the throttle opens and closes by the feedback it gets about the acceleration of the vehicle.

Is there a way to reset the throttle body?

This method is almost foolproof as long as all ECU control parameters are within their normal ranges. Resetting The Throttle Body Calibration (this step is conditional) A Rough Idle or a SES can sometimes be caused by a change in the throttle body position sensor calibration.

Who is throttle body injection in Largo Florida?

ThrottleBodyInjection.com is a division of Guaranteed Carburetors of Largo, Florida. We are a trusted name for over 30 years in the remanufacturing of OEM carburetors and fuel injection systems for both the automotive and marine industries.

Where is the distributor wiring in a TBI harness?

A commonly overlooked separate wiring section is the 2 wire pigtail that joins the distributor wiring to the coil wiring. This is a separate wiring to the harness but can be included if not present during an engine transplant for examples. Would you like any additional Connectors/Wiring?

Do you need a throttle body repair kit?

If you need to repair your throttle body, and a throttle body assembly is not available for your vehicle, a throttle body repair kit is the perfect solution. At O’Reilly Auto Parts, our throttle body repair kits include all the parts you need to rebuild your original throttle body.

Is the throttle body part of the air intake system?

Touch device users, explore by touch or with swipe gestures. The throttle body is part of your air intake system. It uses a butterfly valve to control the amount of air flowing into the engine based on the position of the accelerator pedal.

Can you change the throttle body on a 350 TBI?

Modify the throttle body. This one pretty cheap but does require removing the throttle body. UTIMATE MODS . Stock 42mm TBI units flow around 450cfm which if you look at http://www.carburetion.com/calc.asp a stock 350 even with a cam upgrade to increase the powerband to 5500 rpms isn’t going to use much if any more than that stock throttle body.

Where can I drop off my GMC TBI?

Repack your core in the box that your TBI assembly came in, adhere the UPS label, and give to any UPS Driver or drop off at any UPS drop box. No paper work or long lines.

When to replace a Chevy c1500 throttle body unit?

AutoZone carries replacements to restore your confidence in your truck. Hitting the gas should open the valve in a throttle body unit for Chevy C1500. If there’s a clog or other defect, there isn’t enough air mixing with the fuel going into the combustion chamber, and flooding, stalling and poor fuel economy are the result.

Where is the fuel injector on a GM TBI?

The GM TBI (Throttle Body Injection) system uses a pair of low pressure fuel injectors mounted above the throttle body opening. Unlike a port fuel injection system, that sprays fuel into the intake manifold runner just above the intake valve, the injectors in this system spray fuel directly into…

Is the throttle actuator in a Chevy Silverado?

Notes: Includes throttle actuator. The combination of excellent handling, comfortable interior and intense power makes your Chevrolet Silverado a full-sized pick-up truck to contend with on the road. Ensure that your performance remains unparalleled by having a fully operational Chevrolet Silverado throttle body unit from AutoZone.

How does the Chevy throttle body injectors work?

by Lee Sallings. The throttle body injection system used by Chevy was a natural progression from the carburetor previously used. Pressurized fuel is strained through screen-type filters before it is introduced into the engine through a pair of injectors located above the throttle body’s venturi and throttle plate.

Where are the throttle bodies located in a car?

Both types of throttle body assemblies (mechanical and electronic) are located between the engine air filter and intake manifold. Most cars use just one throttle body, though some engines (usually those with twin turbochargers) use two throttle bodies.

How does the GM TBI fuel injection system work?

Where is the idle button on a GM TBI?

The “A” and “B” terminals are located on the top right of the connector. Unplug the IAC valve located on the passenger side, rear of the throttle body. Start the engine. Insert a T-30 size Torx driver into the Idle adjustment screw that is located behind the plug removed earlier.

Where is the throttle position sensor on a Chevy 6.0?

Throttle body sensor failure – Chevy 6.0 The throttle position sensor (TPS) is located on the throttle body and is responsible for controlling air flow into the engine. The TPS sensor monitors how open the throttle is (ie. how much air is entering the engine) and relays the information back to the ECU.

What kind of injectors are in a TBI?

Each remanufactured TBI Assembly includes Injectors, TPS, Idle Air Valve, and Bushed Throttle Body Housing. Most TBI’s are “In Stock”and ready for Quick Delivery. We also stock General Motors Rebushed Throttle Body Housings and have an inventory of Multi Port Injectors.

Where are the fuel injectors located on a Chevy?

Pressurized fuel is strained through screen-type filters before it is introduced into the engine through a pair of injectors located above the throttle body’s venturi and throttle plate. Over time, varnish and sediment clog the screens and injectors, causing inefficient fuel atomization.

What are the symptoms of a bad throttle position sensor?

Symptoms Of A BAD Throttle Position Sensor (TPS) Beside the CHECK ENGINE LIGHT (CEL) being on and driving you nuts, your Chevy or GMC pick up (or SUV or van) may be experiencing one or several of the following symptoms: TPS diagnostic trouble codes (DTC’s) stored in the vehicle’s computer’s memory.

How to test throttle position sensor ( GM 4.3L )?

You can find this tutorial in Spanish here: Cómo Probar El Sensor TPS (1996-2004 GM 4.3L, 5.0L, 5.7L) (at: autotecnico-online.com ). Beside the check engine light (CEL) being on and driving you nuts, your Chevy or GMC pick up (or SUV or van) may be experiencing one or several of the following symptoms:

How much does a Chevy S-10 throttle body cost?

Rebuilt presre. reg on throt. bdy & replaced plugs,wrs.cap,rotor,ect. then it started poppin’ & pingin’. cometo find out coil was bad too. But I bought the truck for $400.00 & put about $65.00 into it, with oil change,& $25.00 worth of gas.Runs & drives like a champ now. Thanx again for your input. 10 people found this helpful.

What does throttle body dumping lots of fuel mean?

– CarGurus throttle body dumping lots of fuel. 89 4.3 ltr. model 220 TBI dumping waaayyy to much fuel & flooding engine. Could that be the pressure regulator on top. i have a 91 2.8 tbi that was doing that.

What is the TBI code on a 1990 Chevy truck?

Consult a service manual or see below for any check engine light code definitions. You can use a late 80’s or early 90’s GM TBI definition. If you have access to a scan tool use a hook up for a 1990 350 cu. in. 5.7L Chevrolet truck. For some scan tools enter VIN 10th“L” 3rd“C” 8th“K”.

What does code 32 mean on a GM OBD?

Depending on the model, code 32 can refer to three different systems. Please choose from one of the above links for specific information on each system. The ECM monitors the Baro Sensor circuit. Code 32 can set when the circuit is open or shorted. 32 – Barometric Pressure Sensor Circuit fault.

Where is the throttle body injection ( TBI ) sensor?

Throttle body injection (TBI) units. The next generation of fuel delivers to the engines. The main control sensor is the oxygen (O-2) sensor, which is located in the exhaust pipe. The sensor tells the ECM the amount of oxygen in the exhaust gas, and the ECM changes the air/fuel ratio to the engine by controlling the fuel injector.

Where are the fuel injectors located in a 454 engine?

The throttle portion of both the TBI units may contain ports located above, or below the throttle valve. These ports generate the vacuum signals for the exhaust gas recirculation (EGR) valve, MAP sensor and the canister purger purge system. The fuel injectors are solenoid-operated device, controlled by the ECM.

Do you have to put gas in the throttle body?

My 97 s10 will run great but you have to put gas in the throttle body for it to start.It will turn over but needs the direct contact of gas. There is also this ticking noise that is only heard when you role the key over.

What happens when you have a bad throttle body?

As we told you before, a bad throttle body can mess with the air-fuel mixture, and it can also cause your engine to misfire. Misfires are easiest recognized as small bumps when you are revving the engine.

Where is the throttle body located in a car?

Typically, in most vehicles, the throttle body can be found in between the intake manifold and the air filter or air cleaner of the engine system. Usually, the aluminum is used for the making of the throttle body. The location of the throttle body can be a little different for different vehicles.

Why is my TBI fuel injection light on?

Troubleshooting your TBI Fuel Injection System Most of the problems encountered while installing your fuel injection system or after a time of operation are very simple. If your check engine light is on you more than likely have a hard fault meaning something is grounded out, unplugged, operating out of range or has gone bad.

Where is the fuel line on the throttle body?

Locate the fuel lines attached to the back of the throttle body. The smaller of the two lines is the fuel inlet line. Find the fuel service port: it will be located a few inches away from the throttle body on the inlet line. Screw the gauge assembly from the cleaning kit onto the service port.

How to order throttle body injection stock number?

Click on “View” and be taken to our picture identification page for the stock number you selected. On this ID page you will be able to visually verify that you have selected the correct TBI for your application and then place your order.

Can a defective c2500 throttle body unit be replaced?

If you have a defective Chevrolet C1500 throttle body unit, you’ve lost the performance you crave. AutoZone carries replacements to restore your confidence in your truck. Hitting the gas should open the valve in a throttle body unit for Chevy C1500.

How much horsepower does a 350 ci Chevy have?

These vehicles featured a 350 ci, 5.7 small block Chevy with TBI (throttle body injected) EFI system and swirl port heads. Producing up to 210 hp in factory spec, this engine can also be retrofitted into an older car with a performance carburetor to produce up to 250 hp.

Where can I get a throttle body unit?

If you have questions about the ordering or installation process, get trustworthy advice provided by helpful staff at your nearest AutoZone location, and take advantage of free battery charging and engine diagnostic testing at the same time.

What happens when a throttle body goes bad?

As with any electrical connection, connectivity issues can cause a wide variety of unpredictable signals to be transmitted. In the case of the throttle body (and related sensor), when this happens it causes false information to be relayed to the car’s computer, resulting in faulty corrections to the air-fuel mixture.

Is there a Chevy GMC 350 throttle body?

Chevy GMC 350 Throttle Body This is a Brand New, Genuine GM, Throttle Body with injectors. This fits 91 – 92 Chevrolet & GMC Pickup Trucks and Vans with the 5.7L (350) engine. See below for specifics. This may work for other years and Trucks as well. The OEM part number for this is 17112508. The AC Delco number is 22-3822.

What do you need to know about throttle body injection?

Our OEM Throttle Body Injection (TBI) Assemblies are complete and ready to install. Each TBI assembly is coated with a long lasting aluminum oxide finish. All TBI assemblies are flow bench tested, calibrated and idle adjusted which makes for easy installation.

What kind of body injection does a GMC truck use?

Throttle Body Injection | Chevy GMC TBI Trucks | GM TBI Chevrolet New and Remanufactured Throttle Body Assemblies for 305, 350, 454 Chevy, GM, GMC Trucks, Cars, Vans and 6 Liter and 7 Liter Trucks.

When did TBI chips throttle body injection start?

Welcome to TBI CHIPS throttle body injection services. So Just what is TBI, stands for Throttle Body Injection used by GM in the early 80’s through 1995. The early systems from 1982-1986 are just too old to do much with. 1987-1991 were still SLOW computers with tiny chips limiting what can be done with the system.

What does the throttle body do in a fuel injected engine?

Power™ Throttle Body Assembly by Professional Products®. In many fuel injected engines, the throttle body is the portion of the air intake system that regulates the amount of air flowing into the engine, in reaction to the driver… Two Barrel Performance TBI by Holley®. This product is made of high-quality materials to serve you for years to come.

What kind of throttle body do I Need?

Powr-Flo™ Throttle Body by JET®. JET Powr-Flo Throttle Body is a direct replacement for the factory unit. It can be used to replace a worn out throttle body or to upgrade the existing throttle body.

Which is the best S10 throttle body unit?

Chevrolet S10 Fuel Delivery∕ Chevrolet S10 Throttle Body System∕ Chevrolet S10 Throttle Body Unit Chevrolet S10 Throttle Body Unit Shop AutoZone for Chevrolet S10 Throttle Body Unit. Sort by FeaturedPrice (low to high)Price (high to low)

Why does my car have a bad throttle body?

If you’re experiencing lack of power or rough idle this may indicate throttle body problems. Your computer may also turn on the Check Engine light and put the car into “limp home mode”. In some cases, dirt can build up on the throttle body, and cleaning it may resolve the issue.

What kind of car was the Chevy TBI in 1987?

Amazon.com: 1987 1988 1989 CHEVY GMC TBI THROTTLE BODY TRUCK / SUBURBAN w/7.4L / 454c.i. V8: Automotive

Why is my throttle body injection not working?

When this automotive part is not working correctly, or its electronic sensors begin firing off readings to the onboard diagnostic computer showing problems, it can create car problems.

Where is the throttle body fuel pump located?

As you’re already aware, the throttle body fuel injection system on your 1987 to 1995 4.3L, 5.0L, or 5.7L pickup (or SUV) uses a low pressure (12 PSI) electric fuel pump located in the gas tank.

What should fuel pressure be on a TBI fuel injection system?

Fuel Pressure is critical to the operation of a fuel injection system. Always check to insure that you have the proper fuel pressure. Fuel pressure should be a constant 10 – 15 PSI on a TBI fuel injection system and is typically around 12 – 13 psi. Higher pressure than 15 psi indicates that there is an issue with the installation.

How does idle control work on a GM TBI?

The IAC (Idle Air Control) valve utilizes the on-board computer to fine tune the idle speed according to engine conditions. Remove the wing nut on top of the air cleaner and lift the air cleaner off the throttle body to access the vacuum lines. These are attached to the bottom of the air cleaner.

Is there a bigger throttle body for a TBI?

Larger throttle body. www.rvmorsemachine.com and www.tbiparts.com both offer a 54mm bored 750/800 cfm throttle body. unless you change out the tiny cam your not going to get a benefit from a larger throttle body. Also not going to get any benefit unless the intake is bored to match the throttle body.

Is the GM 454 a throttle body injection?

I’mpretty sure Tim’s is a throttle body injection like mine. These look like a carb but are far from it. For that period it was GM’s answer to a carb and I think they worked better than a carb, but they came with their own problems. I’m having problems with my engine which is a gen 5 454 tbi 220 model made in 1992.

When did Chevy start using the 454 engine?

The LE8 454 was the most common from 1973 to 1991. The L19 TBI, or throttle body injection, powered 1987 and later trucks as the second 454 engine option. The TBI 454 had fuel injectors in the middle of the throttle body that increased fuel efficiency, power and durability. Chevy began installing 454 V-8s in its trucks in 1973.

What makes a GM 454 backfires a carb?

If a 4 barrel it might be the accelerator pump. I’mpretty sure Tim’s is a throttle body injection like mine. These look like a carb but are far from it. For that period it was GM’s answer to a carb and I think they worked better than a carb, but they came with their own problems.

When did Chevy start using throttle body fuel injection?

The return of the 231 V-6 to General Motors cars in the mid-1970s proved that fuel efficiency could be achieved in compact engines. But in 1988, Chevrolet introduced Throttle Body Fuel Injection to the 454. It was the same TBI system used on small-block V-8s and the V-6s.

Is there a complete TBI system for a 2bbl Chevy V8?

Pictured is a TBI complete system for a 2bbl Chevy V8. Some of the components shown above may look different from what will be included with your kit. The complete TBI system comes with all components needed for a closed loop system except for air cleaner, throttle cable/linkage, and fuel lines.

How does the fuel injector work on a Chevy truck?

Instead of spraying fuel directly into the manifold like a throttle-body injector, the MAXI injector routes fuel into six nylon fuel lines that have poppet-style spray nozzles on the end. When the pressure inside the lines reaches the opening pressure of the poppet valves (43 psi), fuel sprays out of the nozzles into the engine’s intake ports.

As you’re already aware, the throttle body fuel injection system on your 1987 to 1995 4.3L, 5.0L, or 5.7L pickup (or SUV) uses a low pressure (12 PSI) electric fuel pump located in the gas tank.

When did Chevy stop using the throttle body?

From 1987 to 1995, a throttle body-injected 5.7L V8 engine was used in everything, from the El Camino to the Silverado, making it widely found in cars and trucks still on the road today.

What’s the difference between throttle body injection and TBI?

Throttle Body Injection = TBI The 4.3, 5.0 and 5.7 TBI’s are all the same CFM with 1 11/16th bores. The injectors are different sizes. The 454 is larger with close to 2 inch bores.

How does a GM throttle body relearn procedure?

A motor and gear reduction set inside the throttle body opens and closes the throttle plate to accomplish your request. Over time, carbon buildup can accumulate around the throttle plate, changing it’s “home” position. If the buildup occurs gradually, the PCM “learns” the new home position.

Throttle Body Injection = TBI The 4.3, 5.0 and 5.7 TBI’s are all the same CFM with 1 11/16th bores. The injectors are different sizes. The 454 is larger with close to 2 inch bores.

How to do throttle body re-Learn Chevy Malibu?

1) Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2) After 3 minutes, turn the engine off and leave it off for 60- seconds. 3) Start the engine again and let it idle in park for 3 minutes one more time. During these run periods you may see a check engine light.

What kind of TBI is used for throttle body injection?

2. Throttle Body Injection = TBI The 4.3, 5.0 and 5.7 TBI’s are all the same CFM with 1 11/16th bores. The injectors are different sizes. The 454 is larger with close to 2 inch bores. It is recommended a TBI from about the same size engine to be used in your conversion or larger for high performance built engines. 3. TBI Wiring Harness.

Can a GM Vortec 4.3L be used for TBI?

GM ran out of valve covers in 1993 and put vortec 4.3L valve covers on both engines. CAMS are expensive and on a TBI 4.3L is only going to gain you about 15hp from 3000-5500 and lose that much below 2500 rpms. So START with a vortec 4.3L and run TBI on it.

Are there any problems with the Chevy 4.3 Vortec engine?

The 4.3 Vortec engines made from 1996-2002 (L35 and LF6) have been reported to have engine knock problems. In a properly functioning engine, fuel burns in even pockets instead of all at once. The pockets burn in even timing, in sync with engine cycles. Engine knock occurs when the fuel burns unevenly and out of sync with the engine cycles.

Where is the idle control valve on a Chevy Vortec?

The idle control valve sits on the throttle body and is responsible for adjusting the amount of air that enters the engine at idle, ultimately controlling engine idle speeds. At idle, the valve blocks a small amount of air from entering the engine, keeping idle RPM’s low.

Why was the GM 4.3 Vortec V6 introduced?

GM also began to advertise a new air/fuel mixing method using a ‘vortex’ inside the combustion chamber that it would brand ‘Vortec.’ Eventually, all of GM’s truck motors would fall under the ‘Vortec’ banner that the 4.3 was introduced under. The larger bore of the 4.3 would help it push past previous GM V6 engines in terms of performance.

Where is the throttle blade on a GM Vortec?

Remove the air intake off the top of the throttle body. You will be able to see the throttle blade inside. If you open it, you can see the baffle on the bottom front of the blade. Take a torx bit screw driver and remove the 2 screws that hold the blade in place and remove the blade carefully.

How does a 4.3 Vortec long block engine work?

Every 4.3 Vortec block must pass our magnaflux inspection designed detect any microscopic flaws or cracking. Blocks are then thermal cleaned followed by steel micro blasting until they achieve a brilliant appearance. Once a block is fully cleaned, we begin our precision boring and honing process.

What’s the pressure on the throttle body injector?

Injector pressures range from 13 to 16 psi (low pressure system) or 35 to 60 psi (high pressure system), and are kept constant by the fuel pressure regulator.

What kind of injection pump does a GMC 6.5 use?

Changes were made by GM to the 6.5 in their light trucks for emissions or reliability improvement. The 1992-1993 model years used a 6.5-specific Stanadyne DB-2 mechanical injection pump. GM replaced the DB-2 with the electronic throttle DS-4 in 1994-2000 vehicles. The DS style pump used a pump mounted driver known as the PMD.

When did the GMC diesel injection pump come out?

In mid-1996 GM implemented a redesigned engine cooling system incorporating twin non bypass-blocking thermostats and a 130 GPM water pump. This improved the flow through the block by 70-75% and flow to the radiator 7%.

How to troubleshoot the fuel pump on a GM 4.3L?

Troubleshooting the fuel pump (GM 4.3L, 5.0L, 5.7L) (for ‘Spider’ fuel system equipped vehicles). How To Test The Fuel Pump On GM TBI Fuel Systems (for throttle body fuel injection fuel system equipped vehicles).

Where can I buy a GMC Sierra fuel injector?

Shop AutoZone for GMC Sierra 1500 Fuel Injector. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only

What happens when you test the fuel pump?

When testing the fuel pump with a fuel pressure test gauge, you’ll get one of two results: correct fuel pump pressure, or low/no fuel pump pressure. The fuel pump is getting power and Ground. The fuel pump fuse is good. The fuel pump relay is good. The fuel pump is bad. Testing the fuel pump is something you can do.

When did GMC End production of the TopKick?

After struggling to enter joint ventures or sell the rights to its product line, the company ended production of the Kodiak and TopKick in 2009. The final medium-duty truck, a GMC TopKick 5500, rolled out of Flint Truck Assembly on July 31, 2009.

Is the Chevy Kodiak the same as the GMC TopKick?

Slightly smaller than the Kodiak/Topkick, the Silverado 4500/5500 is marketed exclusively as a Chevrolet (with no GMC counterpart). For 1980, General Motors introduced the Chevrolet Kodiak and GMC TopKick short-hood conventionals.

How many GMC trucks have throttle body injection?