How do you remove a pulley from a power steering pump?

First, place the power steering pump in a vice on a work bench. Attach the pulley removal tool to the pulley. Guide the locking nut onto the edge of the pulley. Using a socket and ratchet, slowly loosen the pulley while holding the pulley attachment nut with a corresponding end wrench.

What happens when a power steering pulley breaks?

This pressure is applied to the hydraulic fluid inside the lines that connects the pump to the steering gear box. When the power steering pump pulley is wearing out or has broken, it may display a few common warning signs that indicate service is needed.

How does a power steering pump work on a Ford truck?

On a Ford light truck or car, it is pressed onto the power steering pump shaft. It is held on by friction, meaning no bolts or retaining clips hold the pulley onto the shaft. To remove the pulley from the power steering pump, a special power steering pump pulley puller is required.

Where is the serpentine belt on a power steering pump?

To remove the serpentine belt, loosen the tensioner pulley that is located on the left side of the motor (as you’re looking at the motor). Once the tensioner pulley is loose, you can slip the belt off rather easily. If your power steering pump is driven by the drive belt, you’ll have to remove this belt as well.

How can I tell if my power steering pulley is broken?

When the power steering pump pulley is wearing out or has broken, it may display a few common warning signs that indicate service is needed. You many notice a whining sound coming from the pump pulley, the power steering feeling tight when driving, or the pulley being damaged when a belt breaks.

Can a pulley be removed from a power steering pump?

Removing a power steering pump pulley is easy if you have the right tools, and most auto parts stores will loan you a power steering pump pulley, so make sure you ask for a pulley removal tool if you are going to replace the power steering pump on your car.

What do I need to replace a power steering pump?

Power Steering Pulley Puller set (to remove and attach the pulley). Some auto parts stores will loan the tool sets. Socket set. Open end wrench set (for use with puller set). Leverage pipe or extension bar (in case the pulley is hardened on the spindle).

How to adjust and replace a power steering drive belt?

Ease the belt onto the pulley. Never try to lever off the old belt, you may damage the pulley. Slacken the adjuster and pivot bolts, and push the pump inwards by the cast front plate until the belt is slack enough to ease off. Do not push against any other part of the pump or pipework, or you may damage it. Remove the old belt.

How much power steering fluid do I Need?

Two (2) quarts power steering fluid or appropriate ATF (to flush and fill). More than 2 quarts if flushing the rack is desired. Power Steering Pulley Puller set (to remove and attach the pulley).

Is the power steering pump a line replaceable unit?

In my opinion, the power steering pump should be viewed as a line replaceable unit. Rebuilding will not be addressed in this instructable. The pump replacement is easy to do once a few tricks are recognized. For example, do not attempt pump replacement without locating a power steering pump pulley puller.

How do you replace a power steering press?

The press has two pieces — (a) a through bolt, and (b) a hub press. 1) Screw the hub press completely on the through bolt. 2) Grease the pulley and the pump hub. 3) Place pulley on pump hub. 4) Attach through bolt into hub. NOTE: Be absolutely certain to tighten the through bolt completely in the hub.

Can a hammer be put on a power steering pulley?

If not get a small ball hone like they use on brake cylinders and give her a few rounds until it slides on the shaft. A hammer onto the pulley is a VERY bad thing for the pump. I’m going to assume that the pump shaft is clean and free of burrs as well. That problem is pretty easy to spot.

How to replace a power steering pump on a Lincoln Continental?

Loosen the adjusting and pivot bolts from the alternator, if you have a Lincoln Continental with a 5.0L engine. Use a ratchet, ratchet extension and socket. Push the alternator towards the engine and slide the drive belt off the power steering pump. Place a drain pan underneath the engine in the direction of the power steering pump hoses.

How do you replace a power steering pulley?

Anytime you install a new power steering pump and pulley, you need to install a new belt. The process for installing this unit is exactly opposite from the removal. Secure the pump to the engine block by screwing bolts through the bracket to the block. Tighten bolts before proceeding to recommended torque pressure.

Where is the tensioner pulley on a power steering pump?

Step 3: Remove the serpentine belt or drive belt. To remove the serpentine belt, loosen the tensioner pulley that is located on the left side of the motor (as you’re looking at the motor). Once the tensioner pulley is loose, you can slip the belt off rather easily.

How do you remove Pully from power steering pump?

To remove the pulley from the power steering pump, a special power steering pump pulley puller is required. Remove the power steering belt. Loosen the tensioning bolt and push the power steering pump toward the engine. Then remove the belt.

How do you install a power steering pump pulley?

Hold the nut on the puller shaft with a wrench. Attach a socket and ratchet to the bolt head on the end of the puller shaft. Turn the ratchet clockwise to draw the pulley off the power steering pump shaft.

How much to have power steering belt replaced?

On average, a power steering belt is going to cost anywhere from $11 to as much as $48 without any sort of professional installation.

What should I do if my power steering pump wont start?

If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. Best all around oil can for the garage?

How to remove a Ford power steering pump pulley?

Removing a Ford Power Steering Pump Pulley. 1 Step 1. Remove the power steering belt. Loosen the tensioning bolt and push the power steering pump toward the engine. Then remove the belt. 2 Step 2. 3 Step 3. 4 Step 4. 5 Step 5.

How do you install a new power steering pump?

Place the new pump into position and install the three mounting bolts. Most power steering kits come with new O-rings for the high pressure hose. Install those now. Reconnect the high pressure side hose, but leave the return line hanging. This is to allow the flush of the power steering system to occur.

How do you remove a pulley from a car?

Pulley removal. Place the drain pan under the vehicle to catch any fluid which may escape from the power steering lines. Loosen the pressure side power steering line at the pump. Continue to unscrew it until it comes free of the pump. Disconnect the return hose from the pump. Place both of these hoses correctly to drain into the drain pan.

Can a lubricant cause a power steering pulley to slip?

DO NOT LUBRICATE THE SHAFT OR PULLEY. If grease or oil is present clean thoroughly before installation. Anything but a clean surface can cause the pulley to slip which would create a failure. Step 5 – Once the desired temperature has been achieved gently align the pulley onto the shaft.

How do you replace a power steering shaft?

Slip the ring over the two-piece adapter to keep it together. Use one wrench to hold the flanged nut, and another to turn the hex head of the puller bolt. As you tighten the bolt, the pulley will slide off the shaft. If you’re lucky.

What to do if you have a power steering problem?

What to do: give your power steering pump pulley a thorough inspection, or have a professional mechanic take a look. If you have a buddy who’s willing to help, safely jack your car up and have one person turn the wheel while the others inspects the power steering belt.

How to replace power steering pump pulley in Chilton Ford?

Turn the nut on the installer shaft clockwise until the pulley is installed on the pump shaft. Unscrew the installer from the power steering pump shaft. Place the power steering belt over the pulley. Slide the power steering pump away from the engine and tighten the adjusting nut. “Chilton Ford Service Manual 2008 Edition Vol.

How to replace power steering fluid in Ford F150?

(Related Article: How to Replace Power Steering Fluid – Ford-Trucks.com) Using a flat tip screwdriver to relieve the hose clamps at each end of the intake hoses, then remove the intake hoses. Place the boxed end of a 15mm wrench on the tensioner pulley (Figure 1), turning it counterclockwise to loosen the serpentine belt.

Do you have to remove PS pump to remove pulley?

Yes, you have to remove the whole ps pump to remove the pulley. Its so not supposed to bend or warp, but if the belt broke, then idk. The allen at the end of the shaft means nothing, so don’t be fooled.

What makes a power steering pump run out of balance?

Old, worn belts can make a pulley run out of balance, eventually making a new pulley run bad. Do not put brake fluid in a power steering pump by mistake. Check all fluids before pouring into an engine or its components to prevent damage from mistakes.

What should I look for in a power steering pulley?

The installation of the pulley should be done in a clean, rust-free shaft. If the shaft and the pulley are not cleaned, then the installation process can become difficult and lengthy. Note: Do not lubricate the pulley or shaft with any grease, water, or any liquid.

How do you remove a pulley from a power steering pump?