How do you change the wiper motor on a Dodge Ram?

Unplug the electrical lead from the bottom of the motor assembly. Wedge a flat tip screwdriver between the firewall and the wiper linkage, and pry the wiper motor off of the linkage assembly. Slide the new wiper motor onto the linkage.

How do you replace a wiper arm linkage?

Push the arm back onto the linkage stud. Step 18: Install the wiper arm retaining nut. Tighten down the wiper arm retaining nut until it is snug using a ratchet, extension and socket of the appropriate size. Note: Itâ€™s helpful to put red Loctite on the retaining nut threads to prevent the nut from backing off.

What’s the linkage between the wiper and the motor?

Car windshield wipers have a link between the motor and the wiper arm and blade. This wiper linkage can get bent and should be repaired immediately. The windshield wiper linkage transmits the motion of the wiper motor to the wiper arm and blade.

How do you remove a wiper arm nut?

Step 3: Remove the wiper arm nut cover. Remove the wiper arm nut cover by prying it up with a small flathead screwdriver. Step 4: Remove the wiper arm retaining nut. Remove the wiper arm retaining nut using a ratchet, extension and socket of the appropriate size.

When to replace the wiper motor on a Chrysler minivan?

If you don’t see a drop to zero, replace the wiper motor. Starting in 1998-2000 Chrysler changed the system just a bit. Now, instead of supplying voltage to the MFS from the BCM for intermittent operation, it gets power from the PDC.

How do you reset the windshield wiper motor?

Insert a pry tool, such as a standard screwdriver behind the cover and gently twist to pop it out of place. Set the cover aside. Use a socket wrench to remove the nut located at the center of the wiper motor. This nut connects the arm linkage to the motor.

How do you replace the wiper bushing on a Dodge Caravan?

Just remove the nut, pull off any washer tubes from their fittings on the cowl or pivots, relieve the spring pressure holding the wiper onto its shaft, and pull it straight up and off. Set the wipers aside in a safe place. Unscrew the fasteners. This Caravan has six, three on the outside and three more beneath the hood.

When to replace wiper motor in Dodge Ram?

Wiper motors for your Dodge Ram will need to be replaced as soon as they show signs of failing such as squealing or hesitation. A wiper motor that fails suddenly while you’re driving can cause a serious accident. Replacement wiper motors can be purchased from most auto parts stores.

What kind of windshield wiper does a 1987 Dodge truck have?

1987 Dodge D150 (should also work for 1973-1993 trucks – can anyone confirm this?) Shortly after my truck’s 20th birthday, while in a driving rainstorm (isn’t that always the case?) my passenger side wiper stopped mid-swipe and just hung there, stuck in the middle of the windshield.

When did my windshield wipers stop working on my 1990 Dodge Caravan?

I have a 1990 Dodge Caravan, and this is how I replace my wipers. I have a 1990 Dodge Caravan. The windshield wipers had been a little noisy for a year or two, and during a recent rainstorm, the passenger side wiper suddenly stopped working altogether.

How do you replace the linkage on a windshield wiper?

Generally, the linkage can be gently pried off the mounts on the motor using a flathead screwdriver or small pry bar. Step 12: Connect the new linkage to the motor. Push the linkage onto the motor. Typically, this can be done by hand, but you can carefully use pliers if needed. Step 13: Mount the linkage assembly.

Can a bent windshield wiper blade be repaired?

How do you remove a windshield wiper motor from a car?

Disconnect the electrical connector from the wiper motor. Remove the retaining bolts from the wiper module (the motor and linkage). Then remove the module from the vehicle and set it on a workbench. Note: On some vehicles, you may be able to remove the motor without removing the module assembly.

When to replace windshield wiper blades in Ram 1500?

This video shows how to replace the front windshield wiper blades in your 2011 Ram 1500. Always replace both wiper blades, even if only one side is streaking – the rubber on the opposite side is likely worn as well.

How can I check for damage to my wiper motor?

Inspect the new wiper motor for any visible signs of damage. Compare the old and new wiper motor side by side to make sure they are the same. Place the new wiper motor back into the same position as the old one. Set your torque wrench to 60 inch-pounds and secure the two bottom bolts first on the wiper motor.

How do you remove retaining nut from wiper motor?

Remove the retaining nut from the wiper motor’s control arm. Remove the two bolts at the top securing the wiper motor and the two at the bottom. The two bottom bolts securing the wiper motor will have two rubber bushings for each bolt, a total of four. Do not loosen them; they are needed for re-installation.

How do you change the wiper motor on a car?

Position the wiper control arm back on the wiper motor pointing down. Set your torque wrench to 204 inch-pounds and completely tighten the retaining nut for the control arm. Plug the wiper motor’s wiring harness back in. Put the grill back over the cowl. Unwrap the negative battery cable terminal and reconnect it to the negative battery post.

How do you change the wiper motor on a Dodge Ram?