How do you change the rotor on a Dodge Ram 1500?

Remove these two bolts and lift off the bracket. The rotor should easily slide off the lug bolts, just as if a tire was being changed. Occasionally it will be rusted in place and need to be tapped with a hammer; be careful not to damage the lug bolts. Slide the new rotor into place and replace the caliper mounting bracket.

Do you need to change brake pads on Dodge Ram 1500?

Leaving this ridge in place will damage new pads fairly quickly, and the decision was made to replace both rotors as well as the pads. If the rotors are grooved to point that you can actually see the grooves the rotors will need to be replaced or turned at a machine shop.

When to replace distributor cap and rotor on Dodge Ram?

No only do these components wear from regular use, but they are made of plastic that can become brittle and fail with age. With the cap and rotor being such important parts of the ignition system, regular maintenance is recommended to keep your Ram truck running at it’s best. This article applies to the Dodge Ram 1500 (1994-2001).

What’s the best way to remove brake rotors?

Repeat Step 4 through Step 7 for the rotor on the other side, if so desired. Put everything back together in order by reversing the steps. If you’re replacing the rotors, be sure to spray them with a quality brake cleaner to wash off the sticky coating that comes on them.

How do you remove the brake rotors from a Dodge Ram?

Apply the parking brake and release the hood latch. Place a wheel chock behind one of the rear tires. Open the hood and remove half the brake fluid from the master cylinder reservoir with a turkey baster and discard responsibly. Replace the master cylinder cap securely.

How do you replace disc pads on Dodge Ram 1500?

Remove the disc pads from the rotor. There is a small clip at the top and bottom of the opening where the pads came out; remove them. If the rotors are in good shape and are not to be replaced, clean the clips, lubricate them with brake grease and refit them into the place they came from. Replace the pads with new ones.

How do you remove rotor from wheel hub?

Pry the caliper and pad assembly off the rotor and support it to the suspension using a caliper hook or metal hanger. Remove the caliper adapter bolts using the impact gun and a suitable socket. Remove the adapter. Remove the rotor from the wheel hub assembly.

When do you change brake pads on a Dodge Ram?

Dan has been a homeowner for some 40 years and has nearly always done his own repair and improvement tasks. He is a licensed electrician. There comes a time in every car’s life when the brake pads and/or rotors must be replaced.

What do you use to break tires on Dodge Ram?

Break the lug nuts loose on both front tires using the breaking bar and a socket. Some lug nuts on Dodge Rams may take a 7/8-inch socket or a 22 mm can be used.

How do you change the brake fluid on a Dodge Ram 1500?

Open the brake fluid reservoir and make sure there is room in it for more fluid; compressing the calipers will result in fluid entering the reservoir. Check periodically to make sure it is not running over. If needed, a clean rag can be inserted into the reservoir soaking up some of the fluid and remove it.

When to replace brake rotors-Advance Auto Parts?

Like dished rotors, deep grooves are a problem because they don’t provide your pads a smooth, flat contact area, and this reduces your braking performance. 3. Bluing and hot spots. Your rotors get hot. If they aren’t able to properly dissipate heat, your rotors may be left with a blue ring or spots.

How much does it cost to replace a rotor?

Technology has advanced, however, and today’s rotors are often manufactured with lighter and less expensive materials. In fact, many drivers can buys a new rotor for under $50. This is often less than what you’ll pay in labor costs to have a technician resurface your rotors.

How to change front disc brake pads on Dodge Ram 1500?

Begin by loosening the the bolts holding the wheel on, and raise the vehicle so that the tire is off the ground. Use of a jack stand or other method of supporting the truck in the air is mandatory; never trust the jack to hold those thousands of pounds up while you are under the car.

Where can I buy a 1997 Dodge Ram?

MoparPartsGiant .com offers the lowest prices for genuine 1997 Dodge Ram 1500 parts. Parts like Front Axle Assembly are shipped directly from authorized Mopar dealers and backed by the manufacturer’s warranty. Parts fit for the following vehicle options.

How to replace a front axle on a Dodge Ram?

This video covers how to replace a front axle universal joint and a hub or wheel bearing in a 1999 dodge ram 1500 4 wheel drive. Very similar to a 2500. It may be less damaging to loosen the hub bolts and tap on them with a hammer vs the method shown in this vid. Loading…

How do you remove a brake rotor from a car?

Inspect the caliper slides on the bracket and add a small amount of brake grease to lubricate. Step 11 – Next, use a hammer and strike the rotor near the edge of the axle flange, this will force the rotor free. Step 12 – After the rotor has been loosened, grasp it using both hands to remove. (Note: brake rotors can be heavy.)

How do you change the brake pads on a Dodge Ram?

The calipers must be compressed back into the assembly. Using a C clamp or similar tool along with the old brake pad slowly compress the calipers. Open the brake fluid reservoir and make sure there is room in it for more fluid; compressing the calipers will result in fluid entering the reservoir.

What causes a car’s brake rotor to wear out?

Brake rotors are metal discs that are attached to the axles of a vehicle. When the driver pushes the brake pedal, the brake pads press on the rotor, creating friction, which forces the wheels to turn slower. That friction also causes the disc to wear out, and to need resurfacing (turned).

How do you change the rotor on a Dodge Ram 1500?