How do I Reset my Computer on a 2006 Impala?

Turn the ignition key to the on position but don’t crank the engine. Press the “reset” or “clear” button on your scan tool (the exact phrase of the button varies depending on the make and model of scan tool you own). This will clear the codes from the computer.

How can I reset the GM ABS brake module?

Navigate to the “ABS” menu on the computerized scan tool by pushing the down arrow button. Select “Clear all codes.” Power off the computerized scan tool and disconnect it from the DLC connector. Turn on the vehicle and verify that the ABS module is no longer lit. A computerized scan tool can be purchased online, or at any automotive supply store.

Why is the traction control light on in my Impala?

It all adds up to a real mess. The most likely cause is a chaffed wiring harness. Shops report that the wiring harness my rub against the transmission or engine and rub through to short out wires.

Can you reset the ABS light without scan tool?

How to reset ABS light without scan tool; this is what you need to know! Every time you ignite your car, the ABS light, alongside other lights on your dashboard, will always turn on. This is perfectly normal, and it means that the light bulbs are functioning as they should.

It all adds up to a real mess. The most likely cause is a chaffed wiring harness. Shops report that the wiring harness my rub against the transmission or engine and rub through to short out wires.

How to reset the service engine light on a 2006 Chevy?

Remove the cable clamp from the terminal. Wait at least 15 minutes. Put the clamp back on the negative side of the terminal. Always take care to never allow the negative cable clamp to touch the positive side of the battery terminal. Put the key into the ignition and start the engine.

Why does my GM ABS brake still run?

The antilock brake system (ABS) is controlled by its own computer. When it senses a problem, the ABS module on the dashboard will light up. When the problem is fixed, the module will sometimes still stay on, and it will need to be rest.

Where are the diagnostic codes stored on an Impala?

These codes are stored on the computer until you run a diagnostic test and retrieve them. Once retrieved, you can fix your Impala, but the codes will remain on the computer. To get rid of them, you’ll need to clear the codes using a special tool called an OBD (onboard diagnostic) scan tool.

Where is the fuse on a 2006 Impala?

Pull down on the fuse panel cover in the driver’s side foot well below the steering column with your fingers. Locate the open OBD port (a rectangular port) to the left of the main panel. Plug the OBD plug from the scan tool into the open port.

Where is the OBD plug on an Impala?

Locate the open OBD port (a rectangular port) to the left of the main panel. Plug the OBD plug from the scan tool into the open port. Turn the ignition key to the on position but don’t crank the engine.

How to reset the computer in a 1998 Chevy truck?

How to Reset the Computer in a 1998 Chevy Truck Open the hood of your Chevy truck and loosen the retaining nut on the cable that runs to the negative battery terminal. The nut is on the cable’s clamp, and must be loosened with a 10mm socket and socket wrench.

How do you reset the computer on a Chevy Malibu?

Unplug the computerized scan tool from the port. Turn on the engine and observe the instrument panel to make sure all warning lights have shut off. The computer is now reset. Turn the key in the ignition to the “Key on/Engine off” position. Locate the diagnostic link connector in you Chevy Malibu.

Is there a way to reset the engine control module?

There are a few ways to reset your Engine control modules. One way is by disconnecting the battery cable for 2 to 3 minutes and waiting to see if the check engine light comes back on upon reconnecting the battery and start the car.

How to reset the computer on a 2001 Monte Carlo?

How to Reset the Computer on a 2001 Monte Carlo Put the key into the ignition and turn it to the “on” position, but do not start the engine. Plug the computerized scan tool into the diagnostic port under the dash. You can buy a computerized scan tool from your local auto parts retailer.

How to reset HVAC door in 2008 Impala?

2008 Impala base 3.5 model was not blowing any heat out of my defogger vent and floor vent, only out of upper dash vents, regardless of setting. With the key in the off position, I pulled the 10 amp DISPLAY fuse as noted above from the fuse panel under the hood and waited about 2 minutes.

Where can I find the Chevrolet Impala owner manual?

Please refer to the purchase documentation relating to your specific vehicle to confirm each of the features found on your vehicle. For vehicles first sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division wherever it appears in this manual. Keep this manual in the vehicle for quick reference.

When to do a TPMS reset on a Chevy Impala?

It is also recommended to do a TPMS reset after a wheel or sensor replacement. Use the VT56 or VT46 branded tools to change placard pressure for the Chevrolet Impala, years 2008-2020, if upsizing tires/wheels, also when replacing with off-road tires or low-profile tires.

When to change the placard pressure on a Chevy Impala?

Use the VT56 or VT46 branded tools to change placard pressure for the Chevrolet Impala, years 2008-2020, if upsizing tires/wheels, also when replacing with off-road tires or low-profile tires. Please note: to determine appropriate placard pressure, always follow the tire load and inflation standards.

How do I Reset my Computer on a 2006 Impala?