Can a JD 535 Baler make dense rolls?

HELP!! my JD 535 baler will not make dense rolls. it rolled 450 rolls last year. I had the tension cylinders rebuilt last year and the baler worked good. this year it will not make dense bales.

What’s the problem with a JD Rd Baler?

Back when I served as a JD dealer service manager (’74-’87) I was taught that the factory belts on JD rd balers shrunk not stretched. Have you performed an internal leak test on both tension cylinders? It’s possible tension adjusting valve is faulty. Have you tried baling a bale with baler hyd hoses unplugged from tractor?

What should I do if my twine on my baler is not working?

Adjust tucker finger. finger did not pick up needle twine. (Check baler manual) 2. Needle did not place twine 2. Adjust needle. into twine disc. (Check baler manual) 3. Hay dogs did not function properly. 3. Check to see if hay dogs are stuck or have broken a spring. A Simple Knot in the Twine End

What causes a needle to go out in a hay baler?

No Knot in Needle Twine POSSIBLE CAUSE REMEDY 1. Improper tucker finger action. Tucker 1. Adjust tucker finger. finger did not pick up needle twine. (Check baler manual) 2. Needle did not place twine 2. Adjust needle. into twine disc. (Check baler manual) 3. Hay dogs did not function properly. 3.

HELP!! my JD 535 baler will not make dense rolls. it rolled 450 rolls last year. I had the tension cylinders rebuilt last year and the baler worked good. this year it will not make dense bales.

How long does it take to wrap John Deere bales?

Once the new balers eject a completed bale, it is wrapped and placed on the ground in 37 seconds; John Deere says the machines can produce and wrap up to 60 bales per hour.

What causes the clutch on a round baler to slip?

Slip Clutch Slipping. It usually makes a noise and starts to smell burnt if its slipping, but if it is too worn it might not and may need replacing. Check for blockages or stuck chains/ bearings to see what is causing it to slip.

Do you have to open the tailgate on a round baler?

Open the tailgate. On Many balers you have to shut the tailgate with the baler running, you may have to open it when starting the baler to get it going Check Belt Tension. Refer to your owners manual and make sure your belts are running at the right tension.

What should I do if my baler is too low?

5. Tighten bale case tension. 6. Baler R.P.M. too low. 6. Tighten bale case tension. Common Baler Problems and Their RemediesTwine Breakage at Knot POSSIBLE CAUSE REMEDY Sharp edges around knotter. Trace the cut to the shearing point on the baler. Smooth all rough edges in the twine path. Title TroubleShootingGuide Created Date

What’s the best way to remove a retaining pin on a baler?

Take a 9/16-inch wrench on the nut at the bottom of the pinion shaft and rotate back and forth to see how much wear is present. 5. To remove the billhook pinion, raise the knotter frame up until the billhook roller is at the 7 o’clock position. Take a 3/16-inch pin punch and drive out the retaining pin.

How big is a John Deere 535 Baler round?

5X6 BALER, NO WRAP, DOUBLE TWINE ARM, 31.5X13.5 (40%), GOOD SPLICES, AVG BELTS, NEW TOP ROLLER AND BEARINGS, BALETRAC MONITOR, TWO LOCAL OWNERS. Before driving to see this item, please call or email to confirm availability. 1994 John Deere 535 Baler-Round — Call for Price! Used, AVAILABLE Immediately, For Sale Status On Yard

What should I do if my round baler is not working?

Check Belt Tension. Refer to your owners manual and make sure your belts are running at the right tension. Worn Belts. If your belts are too worn they will have a hard time gripping when there is no hay in the chamber, you may need to replace your belts. Improper Windrows/Driving.

Can a 535 John Deere round baler return?

At I have a 535 deere round baler and the twine arms will not return. They also take off on their own and not return. At – Answered by a verified Technician We use cookies to give you the best possible experience on our website.

How to reduce twine tension on a hay baler?

Increase twine tension at the twine box. Add hay wedges if baling springy material. Check and adjust needle-to-plunger timing. Tighten the twine holder spring bolt; turn and test it. Decrease baling tension or remove hay wedges to decrease density. Decrease twine tension at the twine box.

Why are the twine arms on my John Deere not returning?

I have a 535 john deere round baler and the twine arms will not return. They also take off on their own and not return. At first is seemed that when you kicked out the bale they hyd’s was not releasing and sometimes the arms would take off and if you kept the hyd on they would come back.

What makes a John Deere 535 Baler different?

The biggest difference is in the twine system. The 535 uses a twine pump on the baler that looks a lot like a power steering pump on a car. This pump has a lot of springs and trips to make the system work. It is dependable but when it gives trouble it is sometimes hard to figure what is wrong.

Can a John Deere round baler be returned?

I have a 535 john deere round baler and the twine arms will… Customer Question I have a 535 john… I have a 535 john deere round baler and the twine arms will not return. They also take off on their own and not return.