Why does my car not start when I turn the key?

This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start. A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine.

Why does my GM car say no start no crank?

How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.

What causes an engine to turn over but not start?

If when you turn the key the engine turns over normally but will not start, there can be any number of reasons for this problem. Some basic checks will need to be done to diagnose this problem. 1. Do you have fuel pressure. Some cause of low or no fuel pressure are a plugged fuel filter, faulty pump relay, blown fuse, bad fuel pump.

How to reset PassLock reset system on Chevy?

1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine.

What causes a Chevy Astro van to not start?

In the Chevy Astro van, power is supplied to the fuel pump by the the gray wire on the electrical connector when the engine is being cranked. If power is supplied, hitting the fuel tank with the flat side of a hammer while someone else is turning the ignition key to start will sometimes bump the fuel pump enough to allow it to start.

What to do if your Chevy Express won’t start?

It sounds like it’s trying to start but won’t. The key only comes out in vans that are equipped with the V.A.S.T system. Weirdly banging on the dash sometimes works too. If it does not try to start for a second and then die, replace the cap and rotor. This video is about an issue involving the disabling of the fuel pump for security. Loading…

This problem may be attributed to a circuit that has failed, so no matter how many times you turn the key, the vehicle will not start. If the circuit has not yet completely failed, you may hear a clicking noise as you try to turn the key.

How long do you leave the key in the ” on ” position?

Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2. Turn the ignition switch to the “OFF” position for 30 seconds.

What causes a car starter to not turn over?

However, when powered, it should send a signal to the starter relay once the key is turned or the starter button is pressed. If you press this button or if you turn the key on a manual ignition switch and the vehicle does not turn over, it may be caused by a problem with the starter relay.

What’s the best way to turn a car key?

Worn, damaged, or bent key. 1. Try pulling the key out a very small amount before gently turning key. (About 1/16 of an inch, the thickness of a nickel). 2. Wiggle key while trying to turn key gently.

How do you remote start a Chevy Camaro?

Press and release the Lockbutton and then press and hold the button until the turn signal lamps flash to start the engine from outside the vehicle. After entering the vehicle, turn the ignition to the ON position. • During a remote start, the engine will run for 10 minutes.

How to start a Chevy Camaro with a dead FOB?

Chevy Camaro with a dead key fob: Get in and start push button start models. – YouTube Chevy Camaro with a dead key fob: Get in and start push button start models. If playback doesn’t begin shortly, try restarting your device.

How do you open a locked Chevy Camaro?

POWER DOOR LOCKS Press the power door Lock/ Unlockbutton, located on each door, to lock or unlock all doors. An open door will not lock. To open a locked door from inside the vehicle, pull the inside door handle to unlock the door and then pull the handle again to open the door.

How does the alarm work on a Chevy Camaro?

The turn signal lamps will flash and the horn will sound. Press and hold for three seconds to activate the alarm. The turn signal lamps will flash and the horn will sound until the button is pressed again or the ignition is turned on. Trunk Press and hold to unlock the trunk.

Why does my car lock when I close the door?

If a door isn’t fully closed or the sensor goes, the car thinks you’re constantly closing and opening the doors. When you ‘open’ the door, it auto-unlocks. When you ‘close’ the door, because you’re driving, it auto locks the door. I had that exact issue a couple weeks back when I closed the passenger seatbelt in the door.

Why is my 86 door lock not working?

The wires after years of being flexed back and forth can develop cracks in the insulation. Been there, done that. It could be something else, but the first place I’d check in an 86 is the wire that goes into the door.

Why is my car not locking or unlocking?

The body control module controls the locking function. If there is a conflict in one of the door locks that tells the module it is not closed or not locked, the module will cycle the locks. First, try replacing the remote battery to be sure it is not causing the issue.

Why does my car door lock not work?

If the door lock relay has any internal or wiring issues, it can cause the door locks to function intermittently. The door locks may function correctly one moment, and in the next will cease to operate. This can be an inconvenience to the driver when trying to lock or unlock the vehicle.

What to do when your car key wont work?

It works mostly in models of Volkswagen, Mercedes-Benz, and BMW and is applicable even when the key fob is damaged or has a dead battery. In case if you are driving a Honda Accord, the trick needs a bit of modification. After inserting the key into the driver’s door lock, turn the key to unlock, lock and then lock position again.

What causes a door lock relay to not work?

Power door locks do not function. Power door locks that do not function are another common symptom for a problem with the door lock relay. If the power door lock relay fails, it will cut off power to the entire power door lock system and may cause them to not function correctly.

A low or bad battery can be easily tested with a standard ohm meter or at any auto repair shop or parts store (they usually do this free of charge). A loose battery cable connection is often the simplest of causes for a non-start. A bad starter solenoid means replacement is needed.

Why does the keyswitch not turn the starter?

They keyswitch may not be sending the signal to tell the battery to send juice to the starter, the battery may not be able to send enough power to the solenoid to turn the starter, the solenoid may not be ramping up the power given to it, or the starter may not be functioning and able to turn.

What happens to the engine when you turn the key?

Turning the engine causes the pistons to rise and fall in the engine block, activates fuel and spark, and (hopefully) ignition of the engine so that it begins running on its own without the starter motor turning it.

Why does nothing happen when I turn the key?

Think of this process as a water pipe with a series of loops that get smaller and smaller in diameter, increasing the water pressure without increasing the amount of water flowing through. This makes the water jet out the other side faster and further than it would have at its original pressure. Like a https://youngchoppers.com list of hitches.

There are a lot of ways the cars can not start. One of the most annoying ways is when you turn the key and nothing happens. Also, you may have just changed the battery and have no reason to believe it is bad.

How to diagnose no start, turn key and nothing happens?

Spark (Only gas engines need a spark, diesel engines need high compression and glow plugs in cold weather to start) Compression (without compression the engine will not run, or not have any power) To read my article where I really lay out the FastC method of diagnosing any no start condition read here.

Why does my Silverado 2500HD no start no crank?

If it helps, usually when this happens, the first time you try to start it, it will start for like a split second and stall out. From there on it just makes a soft clicking at the relays and won’t crank. I usually do not do a lot of repairs to my truck myself.

What happens if you damage a car key?

If you do damage a chip key, or get it wet, regardless of how many jumper cables you hook up to the car it will never start. You will have to pay for a new key or pray that you have a spare chip key.

Why did my 1999 C5 Corvette not start?

1999 Corvette, The TPS and the Key-fobs are not being received by the transceiver. tried a different receiver still nothing. they did work when i got the … 1999 C5 corvette died after starting 3 times after I put it in gear.

What happens if you turn off the engine without a key?

The ignition cylinder is mechanically connected to the steering wheel lock, so a potential thief cannot steer the car without the key. If you turn off the engine with the steering wheel turned or turn the steering wheel after turning off the engine, the steering wheel lock can bind and prevent you from turning the ignition.

What should I do if my Vette won’t start?

Connect them to both batteries and wait at least five minutes to give the old battery some time to charge. Then, attempt to start the car again and let it run for a bit. If your battery holds a charge going forward, you are good to go. If the battery dies again, it could be going bad, or you may have another issue.

What to do when your Corvette C5 wont start?

Pull the correct fuses (found in the owners manual) and reset the codes. If that doesn’t work you can try this little trick: set the heat on high, shut the car off, discount the battery on the negative side, wait five minutes, reconnect and see if your problem has gone away.

How much does it cost to replace a corvette key fob battery?

A key fob battery is inexpensive (around $10), but if a Corvette owner were to pay their dealer to test and replace it, it could be up to one hour of dealer labor (around $100). Figure 3. The issue could be a faulty key fob battery.

If there is no sound when you turn the key, but the lights and accessories work, it could be the stater relay or starter solenoid. However if there is no sound at all, not even a click, it’s probably your battery.

Why does my car make no sound when I start it?

Most likely a dead battery. Start by getting a jump start. Do the lights on the dashboard turn on? If there is no sound when you turn the key, but the lights and accessories work, it could be the stater relay or starter solenoid. However if there is no sound at all, not even a click, it’s probably your battery.

What to do when your car won’t start?

If it doesn’t start it could still be the starter. If you have a manual car a way to get around this (temporarily) is to push the car until it’s going 4-5 mph. Get in and put the car in first and the turn the key and release the clutch the car should start up. This can get you out of a bind really quick.

Why does my car starter not make a click?

The lights take a lot less amperage than the starter, so sometimes the lights come one but the starter won’t turn over the engine. Usually the starter makes a click (at a minimum) when this happens. – xpda Sep 22 ’11 at 19:05 Yes, mine was also started to work for 8 months just by measuring the voltage of the starter. Very strange.

How can I tell if my car battery is not working?

Check the terminals on the battery for corrosion and tightness. A good way to check how tight they are is to try and wiggle them with your hand if you can wiggle them they are not tight enough. Tighten them and start over. Make sure the battery is installed correctly, and there isn’t a build up of corrosion on the terminals.

Why does my car not start when the lights are on?

if the lights are on and remain on when trying to crank but the problem is that the starter does not even attempt to engage then this points to a problem with either the ignition switch or the exciter cable, this is the narrow gauge cable attached to the starter which, when made live, engages the solenoid to begin the cranking process.

Can a car battery stop working when the lights are on?

In fact, you can also run into a situation where the lights will work, but the radio will stop working due to the dead battery, and other even stranger combinations. So while your problem isn’t necessarily the battery, it definitely could be.

How to troubleshoot a no start GM 4.3L pick up?

Testing a Cranks but Does Not Start condition on your GM 4.3L, 5.0L, 5.7L pick up, van or SUV is not that hard to do, if you have a solid diagnostic strategy. In this article I’ll show you the basics of testing such a problem.

Why does my steering wheel not turn when I turn the key?

Turn the Steering Wheel The most common reason that a car key will not turn is that the steering wheel has locked. This will happen when the steering wheel has been moved after the key has been removed from the ignition cylinder. Turn the steering wheel to the right and left.

What does it mean when your car says no crank?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. The most common problem, that causes this condition is a failed starter motor.

Can a 1999 Chevy c1500 / k1500 start?

Hi, our 1999 CHEVROLET C1500/K1500 is having the same issue. After sittiing for a few hours, we have to crank it and eventually put a little gas or tarting fluid in the throttle body for our truck to start but runs and drives fine once it does start and will start right up after only sitting for about an hour or so. 205 people found this helpful.

What to do if your Chevy truck won’t start?

– CarGurus.ca 96 Chevy C1500 5.7L Vortec Truck won’t start, Replaced Fuel Pump, Filter & Has Spark.

Why does my Vortec truck won’t start?

Also I haven’t fully checked the Spark, but the Truck run’s fine when you spray Starting fluid into the Throttle body. Any suggestions on why the truck isn’t accepting the fuel, it cranks fine, just wont run without starting fluid. these trucks have to have between 55-65psi of fuel to run. Get a pressure tester and check it.

If you do damage a chip key, or get it wet, regardless of how many jumper cables you hook up to the car it will never start. You will have to pay for a new key or pray that you have a spare chip key.

Why does my Chevy Silverado want to turn over?

Truck wants to turn over but will act as if is starving for fuel,wait ten minutes, it start. Been happening frequently lately. I also was told it was the security system Will turn key and it is like no power from battery to starter, but have lights, radio, etc. Turn key again or sometimes multiple times, to no avail.

Why is my Chevy Silverado 1500 not starting?

However, today, when the truck will crank and start, the antitheft icon goes off after a few seconds with the key on and stays off while the truck is running. It never flashed either today or yesterday though. And I don’t know if the antitheft system disables cranking or starting or both.

If you turn the key and can hear the starter motor trying to turn the engine over, the lack of power is likely caused by electrical issues such as a weak battery, dirty battery terminals or a worn starter motor. Let’s look at some ways to try to fix them.

Why does my Car start but the starter won’t crank?

If the battery checks out OK, but the starter still won’t crank, there could be a number of possible reasons. Here are some of them: • The ignition switch could be bad – it’s a common problem. An ignition switch is an electrical switch installed at the back of the ignition lock mechanism.

What do you do when your car won’t start?

Recently the car has started doing this not starting. When you open the car it opens as normal, put the key in the ignition and turn it to the on position, the steering wheel moves to position, auto lights come on, sat nav powers up, and heater inside comes on, but the engine does not turn over.

Why does my car engine not turn on?

However, Pin n:2 from the 5pins connector in the BSM ( pin 2 is for the starter ), is not powered when in start position, but when i disconnect the connector, and i check pin 2 in the BSM it is live ?? not sure if this indicates something ? Also, still no comms from ABS/ESP, however the ABS pump is not present so maybe thats why ?

Try: Cycling the Key If your car turns on but won’t start, turn on the dome light and watch it while you try to start the engine. If the light goes out, it’s a sign the battery is really weak—almost dead. To heat up the battery, terminals and starter, try the “key cycling” trick.

What happens when you remove the key from the ignition?

Car Engine Doesn’t Turn Off When Removing Key or Pressing STOP It is a strange problem to have a car that won’t turn off when you remove the key from the ignition or press the Engine Stop button. Your engine will continue to run even when you remove the key from the ignition because the fuel pump is not shutting off.

If the battery is empty shortly after charging, the alternator should therefore be checked for a defect. If the battery is OK, a defect in the starter can be the cause of a non-starting vehicle. Age-related wear or a material defect can damage the starter. This is often noticeable by a clicking sound when trying to start.

What to do if your truck won’t start?

These trucks are notorious for ignition switches!! If it’s a bad starter though, you can turn and hold the key in the “start” position, while someone gives the starter a “whack” with a blunt object! It may start, if it does start, you will know that the starter is kapoot!

What does it mean when your car says no start?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).

Why does my car not start when I put the key in?

Putting the key in the ignition switch and starting the car feels like second nature. However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems.

Why does my Chevy Silverado not start up?

Few things are as annoying as turning the key in your truck and finding it will not start. There are many problems that can result in a Chevy Silverado’s failure to start, making diagnosing the trouble even more frustrating.

If they weren’t, you wouldn’t hear the engine turning over when you turn the key. There are several causes of this type of no-start, but I’ll cover the basics here. An engine needs three things to run: A fuel supply; without fuel, the engine won’t run. A spark (for gasoline-powered engines).

What happens if you have an incorrect ignition code?

The chip in the key transmits a specific code, of which there are millions. If this code matches the ones programmed into the vehicle, engine starting is enabled. An incorrect key code, such as from an unprogrammed key or damaged key, would prevent engine starting. Code “confusion,” such as having multiple keys can also occur, preventing ignition.

To restate what a crank/no start is, it’s when you turn the key and you can hear the engine moving but it’s just not catching and running. You can first eliminate all the above causes in this article because you have confirmed that your starter, cables, and battery connections are likely good.

What should I do if my ignition switch is not working?

How To Fix It: After ensuring the rest of the electrical system is intact, such as fuses, relays, and circuits, replace the ignition switch. The transponder antenna surrounds the ignition cylinder. If it doesn’t recognize the transponder key, it doesn’t allow the engine to run. https://www.gettyimages.com/license/525320791

What causes a car to say ” no start “?

Turning the key to the on position the gauges would sometimes act if they lost power. When attempting to start the engine when the gauges were in this unpowered state, the starter would turn but the there would be no spark coming from the coil packs. I tested the lead and ground to the coil packs and the crankshaft position sensor.

What does it mean when my ” check gauges ” light comes on?

Her mechanical career has spanned 41 years working on everything from Porsches to Heavy Equipment to including classic vehicles which she owns several and has personally restored in a world dominated by men. What Does It Mean When My “Check Gauges” Light Comes On?

Why are the gauges on my Dodge Ram not working?

The interior lights come on the radio comes on but the gauges themselves do not work. I hate to say it but it your ECM might be bad. Check your fuses, relays, and wiring. If none of those work, hook up a diagnostic and see if there’s any codes that you can see to fix it before my assumption. 8 people found this helpful.

How to diagnose a Dodge Dakota no start?

To find out what’s behind your 4.7L Dodge Dakota or Durango’s not start problem, you’re gonna’ need a few specialized tools. Here’s a basic list of what you’ll need: Spark tester. Noid light set. Fuel pressure tester. Engine compression tester. I’m gonna’ suggest that the spark tester that you use be an HEI Spark Tester.

What causes no ignition, or dash lights when turning key?

Q: I have no ignition, or dash lights when turning key. All relays and battery are fine. Dash lights work when headlights are on. I’m thinking its some kind of electrical problem. I got it to start one time with the remote start. After that, nothing. I’ve tried jump box to be sure I have power.

Why are the dash lights not working on my car?

All relays and battery are fine. Dash lights work when headlights are on. I’m thinking its some kind of electrical problem. I got it to start one time with the remote start. After that, nothing. I’ve tried jump box to be sure I have power. All electronic systems work except the dash lights, and ignition.

How does a key turn work on a starter motor?

The key turn completes a small circuit that tells the battery to release power to the starter solenoid. The solenoid ramps up the power given to it and that power causes the starter motor to turn very quickly.

How to disable the theft system on a Chevy Cavalier?

Just leave the key in the run position and the “Theft System ” light on the dash will be flashing. Leave the key on for about 10 minutes and the light will stop flashing and go on solid. Then the theft system is disable.

How to fix a car that won’t start when you turn the key?

How to fix car that wont crank when you turn the key, no sound or click. How to jump start a car, check the starter, and wire bypass trick. DIY car repair with Scotty Kilmer, an auto mechanic for the last 50 years. Thanks for watching! 1. Bluetooth Scan Tool: http://amzn.to/2nfvmaD 2. Cheap Scan Tool: https://amzn.to/2D8Tvae 3.

How to reset check engine light on Chevy Cavalier?

The way it was described to me for OBDII gm’s is to turn the ignition on, depress the fuel pedal for a full minuite, release and turn the ignition off for a full min, then retry. This is also similiar to how you reset check engine light on gm’s newer cars, except you have to hold the radio button while depressing the pedal and IGN on

Do you need a stop watch on a Chevy Cavalier?

36 people found this helpful. yes but if you dont want to have a stop watch lol just watch for the security light to go out. it goes off after 10 mins. make sure you turn it off after the third time before you start it 37 people found this helpful.

Why does my Car start intermittently after starting?

In this case, it’s important that you contact a mechanic as soon as possible so they can determine what is causing the intermittent contact. In many cases an intermittent starting problem is linked to a bad wire connection that may become dirty due to exposure under the hood.

Can a bad ignition switch cause a starter relay to fail?

Although it’s unlikely that you’ll ever experience a problem with the starter relay, it is prone to mechanical failure and will need to be replaced by a professional mechanic if it wears out. Most of today’s modern cars and trucks have an electronic ignition switch that is activated by remote key.

What are common reasons my Chevrolet Impala won’t start?

What are common reasons my Chevrolet Impala won’t start? While there are a variety of reasons your Chevrolet Impala won’t start, the most common 3 are a dead battery, an alternator problem, or failed starter.

Why is the security light not working on my Chevy Impala?

Chevy Impala Won’t Start Security Light. If you’ve had trouble starting your Impala then you may have a common problem with the pass lock engine immobilized system. This system prevents the car from starting when someone is trying to steal it and can occasionally activate when you try and start the car with a key.

What to do if your Impala key does not turn?

Place your key in the ignition of the Impala and try to turn it. If the key does not turn at all or fully, check to be sure that the steering column is not locked as the wheels may be in the wrong position. Turn the steering wheel to the left and then to the right and wiggle the key.

What happens when the starter fails to start?

Starter motor failure produces one common symptom across all makes and models: When you turn the key, the starter solenoid will click, but the engine will not rotate. You also Read More When the computer senses the engine is out of time, it will turn on the check engine light. The engine may stall or even just fail to start.

Why does my GM 4.3L engine not start?

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

What are the symptoms of a bad ignition module?

Symptoms Of A Bad Ignition Module And Ignition Coil Generally, when the ICM or the ignition coil fails, your GM car or truck will Crank but NOT START. Specifically, the ignition coil will not spark.

When did my Impala run out of gas?

The car was running perfect…i havent driven it since October while working on the interior …when i parked it there was around 1/8th of a tank of gas…Ive started the car one a week since …..last week i pulled the car out and let the car run to charge up the battery….well it ran out of gas….

Why did my 2000 Chevy Silverado stop running?

My 2000 Chevy Silverado Pickup stopped running. It will start My 2000 Chevy Silverado Pickup stopped running. It will start and run for a few seconds, but then stalls. I’ve changed the fuel filter, rotor and rotor cap with no success.

What kind of car shut off last night?

Last night I was on I-95 south bound doing about 65mph in my 2002 Chevy 1500 4×4 4.8L and the engine shut off. I costed into the break down lane and shut the key off and tried to start it again and it will turn over but not start.

If your starter spins freely when you turn the key, the problem lies elsewhere. Now you can begin to check the other systems that could keep it from firing up. With the starter-related causes of your problem out of the way, we continue the search for why your car won’t start. Spark is created by your car’s ignition system .

What happens to the battery when the car starts?

After a battery starts a car, the alternator takes over and powers the electrical systems of the car and also recharges the battery, which we’ll talk about next. As long as the car is being run fairly often the battery can be continuously recharged and ready for use.

What causes a car battery to pop up?

1 Faulty Connection. There are two ports or posts that stick up from your battery, the negatively charged post and the positively charged post. 2 Corrosion. Corrosion is another thing that can cause a bad connection to pop up. 3 Disuse. 4 Alternator Problems. …

Why does my car battery drain so quickly?

As long as the car is being run fairly often the battery can be continuously recharged and ready for use. But if the car isn’t being run often, the battery will slowly drain over time and soon won’t have enough juice to send the necessary voltage to the starter. 4. Alternator Problems Battery problems can quickly arise from alternator problems.

Why does my riding mower not start when I turn the key?

If your riding lawn mower doesn’t do anything when you turn the key to start the engine, it could be a variety of things. This video shows you how to pinpoint the cause by checking the riding mower’s battery, solenoid posts and coil, fuse, ignition switch, brake switch and blade switch.

Can you start a starter with the key off?

You’ll have to start tracing back from the solenoid and see where the harness is pinched or has a bare wire in it.. Thumb button shouldn’t work with the key off. So I say start at the solenoid and go from there.. Thanks cmanningjr, will do that 1st thing in the morning.

Why does my car click when I turn the ignition?

The most common problem is a faulty car battery when it comes to cars that click when turning the ignition. Use a jump starter or jumper cables to jump start your car to see if this is the problem. The next most common problem is a bad starter or bad wiring which will need to be looked onto further.

If the engine does not crank, then you may have a starter problem. If the engine does not crank, and the security / theft warning light stays on when it won’t start- and you let go of the key to the ON position, then this is most likely a problem in the Passlock system. The ignition cylinder is also know as the Passlock Sensor.

Why does my Silverado engine turn so slow?

The fact that is cranks slow may be because the engine has been damaged due to overheating as the belt was broke and water pump not turning for a 10 mile trip. The engine must have overheated very badly. I have a 2005 Silverado go to turn it over fires then dies I also lost all power to my locks n windows what could cause this?

Why do I have to turn the key several times?

Would need more info of some preliminary diagnosis. gas then it fires up runs great after that only spits and sputters on start up. of a new fuel pump. Fuel pressure should be checked, or key on. By turning the key several times, you are you definitely have a fuel issue. Also possibly a leaking fuel pressure regulator causing a rich condition.

Why does my Chevy Malibu not start up?

1999 Chevy Malibu. Engine size = 6 Cylinder. The car will not start when the ignition is turned all the way over. The battery is fine and I think it is a switch problem. Sometimes I can leave it alone for a few hours and it will fire right up. Other times I just turn the ignition on and off about 5 or 6 times and it starts.

What’s the problem with my 2001 Chevy Silverado?

My 2001 silverado will not crank, just hold the key in the crank and nothing happens. Battery is good, 12v on main terminal on starter, 0v on little terminal. New starter. New ignition switch. This is an intermittent problem. Usually when I leave alone for awhile it will start up like nothing wrong. Submitted: 11 years ago. Category: Chevy

What does it mean when car won’t turn over but has power?

If you hear cranking, but your car won’t turn over but has power, this could be signaled by loud cranking. The engine starts but dies very quickly. If you use a car that has a carburetor, then check the choke to see if it is closing and opening at the right intervals.

What’s the difference between turning over an engine and not starting it?

A simple way to remember the difference is this: if you turn the key and nothing happens, the engine won’t turn over. But, if you turn the key and you hear that cranking noise and the engine won’t fire, then it’s not starting.

What to do when your car won’t start or turn over?

If you’re not sure, turn on the headlights. When you try to start the car, the lights should either dim considerably or turn off completely. If they do, your ignition switch should be good. If not, the switch will need to be replaced. Bad Starter Connection: Corrosion can keep your battery from connecting.

What happens when there is no power to the starter motor?

If there’s no power to the starter motor but power everywhere else you’d hear a “click!” noise when you turned to start but nothing else – ie. no whirring or cranking noises.

What are common reasons my GMC Safari won’t start?

What are common reasons my GMC Safari won’t start? While there are a variety of reasons your GMC Safari won’t start, the most common 3 are a dead battery, an alternator problem, or failed starter. How is a no-start diagnosis fixed?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).

What happens when I turn the key on the starting circuit?

Now, thinking about that starting circuit, consider the things that could be going wrong to interfere with it.

Why does my car not start at 9 / 10?

This is because 9/10 a no start condition will be because of a bad battery, bad connections, or user error in diagnosing those both. I have started many friends cars that wouldn’t crank, or crank strongly, simply because I saw the battery terminals were loose.

What does it mean when your corvette won’t start?

When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your Corvette, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it. There are a lot of issues that can cause your Corvette to crank, but not start.

Why is my electrical switch on my Corvette not working?

When it does, it usually isn’t making a failing switch work, it makes a failing motor work. It moves the motor armature enough so it get off a ‘bad spot’ and then works. For a few times. Then it fails again. And the same thing could happen for a failing switch. Get it fixed.

Why is my Silverado no crank no start?

I checked the start (8:30am ) before doing anything else and the engine cranked (slowly) but fired and ran on the first attempt. All dash display normal, the alternator charge at 14V and nothing out of the ordinary. I’m pretty sure something was iced up but I don’t get how any thaw took place with conditions here.

When do you let go of the key to start the engine?

When one goes to start the engine it continues cranking (sometimes) after the engine starts and you let go of the key . Sometimes it only does it momentarily; sometimes you have to manually bring the key back so it stops cranking. I have gotten several opinions.

Is it good to turn key and no start / crank?

Automotive Forums .com Car Chat > Chevrolet > Avalanche | C&K | Silverado | Suburban | Tahoe > Silverado > Turn key and no start/crank…bat is good! Turn key and no start/crank…bat is good! Hi guys, Thanks in advance for any help, I have a 01 2500HD Crew cab with the 6.0. Tonight I stopped at the gas station to grab some milk.

What to do when your GMC Truck won’t start?

Try turning your key to the run position a few times (with out starting). Then try to start it. If it starts, sounds like what mine did. I replaced the fuel pump assembly and that fixed the problems. Very common problem.

What to do if your Duramax won’t start?

If the fuse is o.k. if you have a test light or multi meter test the terminals the fuse plugs into,there should be two terminals in the fuse box.Test for power on one of these terminals while someone is trying to start the vehicle.If you have power then the start circuit is good and the fault is in the starter itself.

Why does my 2002 Chevy Silverado not start?

If you’re in a situation where you turn the key in your 2002 Chevy Silverado and the truck won’t start, a number of potential explanations exist for why it may not start. By checking several key components in your Silverado, you can pinpoint the problem yourself and possibly fix it.

Why does my Chevy Silverado turn over but not start?

Before suspecting electrical or mechanical failures, however, ensure that the parking lever is in park and that electrical connections are clean and secure. If the engine turns over but will not start, this usually means that either the engine is not producing a spark at the sparkplugs or fuel is not being delivered to the engine.

Why does my starter turn without turning the engine?

Starter Turns Without Turning the Engine. A starter that spins without turning the engine is caused by the starter gear failing to engage the engine’s flywheel. This usually indicates that the starter pinion is sticking and not allowing its gear to move into position with the flywheel.

What does it mean when your car won’t start?

An intermittent no-start condition references any time where starting is possible sometimes, and other times the engine will not start. This implies that the difference between starting and failure to start is not understood.

Why is my Chevy Impala key stuck in the ignition?

If your Chevy Impala’s battery doesn’t have enough voltage to properly engage the safety mechanisms that leave your key stuck in the ignition can cause the issue. Here are ways that you can get your Impala’s key free. This is our recommended order to do them in. Is the battery charged? If the vehicle still starts it should be fine.

What to do if your key gets stuck in the ignition?

Take the good key and duplicate it. Rusted – A key that is rusted can get stuck in the ignition system easily. It doesn’t have to be a lot of rust. Just enough to keep it from moving freely. As with a bent key, just start over. Once something rusts, it comes back a lot easier.

What to do if your Chevy Camaro key is stuck?

If you have a key that’s in better shape, you’d want to use that one to make a duplicate. If you have no key to duplicate, many manufacturers can use the VIN number to cut you a brand new OEM key. Just be prepared to prove ownership to Chevy in some way.

How much does it cost to get a new turn key?

You will have to pay for a new key or pray that you have a spare chip key. It can cost upwards of $500-700 dollars to have a new chip key programmed, plus waiting for the dealership to open, and to get towed there.

What happens if you put the wrong key in the cylinder?

Factor 3: Incorrect key. Sometimes it’s a simple mistake, and the wrong key is inserted into the cylinder. This happens most often when someone has more than one car key on their key ring. Many keys look similar, especially if they are from the same make. So double check the correct key is being used to try to start the vehicle.

What does it mean when your car won’t turn over?

By saying that the engine “won’t turn over” means that the crankshaft isn’t turning, so the other parts won’t be able to move to start the car. If your car refuses to start, there are a few tricks you can try first to turn your engine over before you call a mechanic.

Why does my car make a noise when I turn the key?

If your engine cranks or turns over when you put the key in the ignition and turn the key, the most likely culprit is actually a dead battery. Although you have done the tests and determined the battery is not the culprit, most of the time, the battery is the cause of the issue if the engine cranks and makes noises.

I think your starter relais is broken. When you turn your key the starter relais will push the starter against the starter ring gear on the flywheel. When the relais is broken no contact is made and therefore you are unable to start the engine.

What happens when you click the starter key?

The starter clicked a single time when I turned the key, and the lights on the radio came on, but nothing else happened. Several hours later, I attempted to start the truck again, and it started just fine.

The most common problem with a starting motor is, when you turn your key and nothing happens. A solenoid or motor that has burned out or electrical issues, may cause this as well. Furthermore, a dead battery can cause the same problem. It may appear that you have power to your starting system, but the engine will not turn over.

What happens when you discontinue power to the starter?

When you start the engine and release the key the circuit will, discontinue the power to the starting motor. If this stays on after the engine has started, the main contacts in the solenoid, have most likely failed. This will ultimately cause serious damage, to the whole starting system and the transmission flywheel.

Why does my no crank no start car not start?

Inside the relay, a set of electrical contacts allows current to flow to the starter solenoid. If these contacts become corroded or extremely worn, they may not get the job done. An external starter solenoid, unlike the relay, carries high voltages.

What causes car to not turn over but Lights Come On?

Sometimes, you need to decide if it is better to repair or replace the battery depending on your car’s value, and the cause of the “car won’t start, but lights come on” situation. Another reason for the “car won’t turn over, but lights come on” situation is that the starter is not working correctly.

Why does my car not start when I Turn on the radio?

If your car won’t start, but lights come on, and the radio is turning on, it could be a few different problems. The most likely culprit for this issue usually deals with the battery.

What happens when the starter doesn’t work?

Basically, with a fully charged battery, and with the key held in the “start” position, the starter is either getting power or it isn’t. With the key in the “start” position, if the starter motor is getting power but the starter doesn’t work, then the starter is condemned and replaced.

Why does my car light come on but the car wont start?

To be certain your car is in good condition, you need to turn on your headlights. The battery is in charge of the headlights and dashboard. So, if the headlight comes on while the car doesn’t turn over, then you have a faulty ignition switch. Another probability is that you have a damaged starter.

If your car won’t start, but lights come on, and the radio is turning on, it could be a few different problems. The most likely culprit for this issue usually deals with the battery.

What happens when you turn key and nothing happens?

If everything’s working normally, it does. However, if nothing happens when you turn the key, or you hear clicking sound (or a series of clicks), it means something’s gone wrong. You can actually do a couple of things to troubleshoot this yourself. Make sure that the car is in park or neutral.

Why is my key not turning in ignition?

The three main reasons why an ignition key will not turn include: problems with related components, issues with the key itself, and ignition lock cylinder problems. Tip: Always make sure your parking brake is on to keep the vehicle secure when following these steps.

Why would a car not start?

The most common of reasons behind a car not starting is a dead battery. When a battery dies or loses its charge, it also loses its electrical power. This prevents the battery from supplying the electrical power needed to start your car.

Why does my starter make a clicking sound when I turn the key?

Clicking sound coming from the starter. The relay is an all or nothing device, meaning that it either sends the full electrical current or sends nothing to the starter. However, there are some occasions when a damaged starter relay will cause the starter to make a clicking sound when you turn the key.

Can a bad solenoid be a sign of a bad starter?

Intermittent operation can be a sign of a failing starter solenoid. Other issues that present like a bad solenoid. Problems that might cause your car to act like it has a bad starter solenoid can include: Bad battery – If the battery voltage is low it will be unable to provide enough power to start your engine.

What happens when you stop pressing the starter button?

Starter stays on after engine started. When you start your engine and release the key or stop pressing the starter button on a modern vehicle, the circuit is supposed to close, which will discontinue power to the starter motor.

Why is the lock on my car not working?

Once this is coupled with a lack of maintenance, it increases the probability of keys being damaged. If the grooves on the key are altered over time, and the key is no longer able to operate the internal mechanism of the lock, it is potentially damaged and this is probably one of the reasons why your car key is not working. 3.

What should I do if my car wont start?

When the security light goes off, turn the ignition off, wait 20 seconds, and then start the engine. These are the most popular ways to solve the problem of anti theft system car wont start.

Why does my car click when I start it?

If the car clicks when trying to start, but still won’t start, this can be caused by a weak battery, dirty battery terminals, a worn starter motor or a stuck solenoid. Here are a few tricks to try if the car doesn’t start:

Why does my car not start when I Turn on the car?

Below are 5 common reasons why your car won’t start and some advice to ensure your car stays in its top shape! A dead battery is the most common reason why your car won’t start. The battery is what the car uses to provide electrical power to the entire car and electrical components (e.g. lights, radio, etc.).

What to do if your car won’t jump start?

If the jump start works, you’re most likely dealing with a dying battery or an alternator that is just having trouble recharging the battery. Consider replacing the battery or alternator, cleaning the connections, or having a technician do the service for you. 2. Defective ignition switch

How can I tell if my car starter is bad?

First, check the starter by turning the key in the ignition to ON and then using a circuit tester or voltmeter to see if there is power to the wires leading to the starter. If there is power, you have a bad starter.

You turn the key and nothing happens, or you hear a single faint click but the motor still won’t crank or start. The bad news is that your starter is probably worn out. The good news is that you can still probably start the engine so you can avoid being stranded in a deserted parking lot.

What causes a car to click when trying to start?

1 Battery Drained. First, did you leave the headlights or an interior light on, or something else that drained the battery while you were sleeping? 2 Cables, Connections and Corrosion. Second, check the clamps for the cables connected to the battery. 3 Bad Battery. 4 Alternator Issues. 5 Starter Motor. …

When to know if your car starter needs to be replaced?

The motor turns very slowly but it still starts. If you twist the key but the motor turns very slowly and you notice the lights on the dash turn very dim while cranking, then you need to have the starter inspected or replaced by a mechanic.

What to do if your Mercedes key won’t turn?

If you have this problem you will have to install a new / virgin EIS. You can not install a used unit because the EIS has to be paired / married to the car using Mercedes-Benz Star Diagnostic Software. They key itself may be the reason why the car doesn’t start. The key may open the doors, but it will not start the car.

What do you hear when you turn the key on a starter?

On starters with the solenoid on top (GM, most others) the solenoid grounds through the starter brushes, so when the brushes make bad contact you get the “silent treatment” when you turn the key. The small wire going to the starter solenoid should get 12 volts or so when the key is turned to “start”.

What does it mean when you turn the key and absolutely?

When I turn the key there’s no clicking sound or anything. At first I thought it was the battery but someone told me it would still be clicking if it was te battery. I didn’t leave any light or anything on. It was running perfectly fine on friday. Please advise as to why this would happen ad what I should do.

What happens when you turn the ignition key?

When you turn the ignition key to the run position, the starter solenoid interlocks the starter pinion gear with the flywheel on the engine to rotate the engine at “cranking speed”. Once the engine starts and exceeds cranking speed, the overrunning clutch releases the pinion gear from the flywheel.

What do you say when your car won’t start?

When your car’s engine won’t start and all you hear is a rapid clicking noise, you’re likely to mutter, “Darn” (or perhaps another four-letter word) and instantly think that something is wrong with the battery. You would probably be right.

Why does my car not start with a full signal?

If the starter relay does not receive a full signal, your car will not start. Sometimes your engine fires up immediately while at times it takes a couple of tries. If this happens to you, it might be a case of cumulated debris on the starter relay. You should clean it up and see if it solves the problem.

Why does my car not start when I push the start button?

On late-model cars with “smart” keys, the key fob transmits a signal that tells the engine that the driver is in the car and allows the engine to be started with a push button instead of a traditional key. If the battery inside the fob has died or the transmitter stops working, there’s no signal, and your car won’t start.

What to do if your car won’t start when you turn the key?

If you can’t hear it running when you first turn the key, it’s time to look in the owner’s manual for the location of the relays. Changing the relay could restore power to the pump and get the fuel flowing again. A flooded engine could also prevent the car coming to life.

It’ll turn over or not. And if not, it’s likely a battery or starter problem. And if so, it’s most likely in the car’s electrical or ignition system. Originally Answered: My car won’t start and is silent when turning the key.

Why does my car make a grinding noise when I turn the key?

Dead Battery: The second most common issue here is a dead battery. Listen carefully to the noise. If it sounds more like a series of rapid clicks rather than metal-on-metal grinding, chances are good that the battery is dead and must be replaced.

Why does my car make no noise when I start it?

The car will not start if you aren’t starting it correctly. This also applies to cars with alarms that have starter-disable kill switches that aren’t properly deactivated. If you are doing everything right, and it won’t start (makes no noise), then the starter is bad, or power is not getting to the starter.

Why does my car key not turn in the ignition?

If your key won’t even turn in the ignition, then it has nothing to do with your battery. This could mean that your steering wheel is locked. This happens sometime when you’re parked on a hill or when one of your tires is turned too far toward the curb. Try to turn the steering wheel a bit to straighten out your tires.

What to do if your car won’t start no noise?

If you truly have no idea what to do to get your car to start, you should wait and call a tow truck. At least if you have a mechanic fix your car, you’ll know it’s safe to drive. So, What is Wrong with Your Car? If your car simply car won’t start no noise, there are a few things that could be wrong. Usually, this has to do with the battery.

Now, thinking about that starting circuit, consider the things that could be going wrong to interfere with it.

What to do if your car key fob doesn’t work?

Other key fob remote problems are more complicated, but it’s still possible to fix them. Here are the five things you’ll want to check first when your remote stops locking or unlocking your car doors: Verify that the remote is actually bad by using a backup remote. Check and replace the key fob battery as needed.

What does it mean when your car won’t start when you turn the key?

The same is true if your headlights come on, but the car won’t start. If your instrument panel lights don’t come on when you turn the key, then your battery is totally dead. You get a jump and it works – If you get a jump, you need to let the car run for a few minutes.

What happens if your car battery is dead and the key fob is not working?

If you cannot then your car battery is so dead that the locks are not working. Your key fob is likely sending the signal to the car to lock the doors but the car cannot lock the doors because of the fact that the battery is dead. All the key fob does is tell the car to lock the doors.

How to fix a car key button that won’t unlock the door?

How to fix a car key button that won’t lock and unlock the door. – YouTube How to fix a car key button that won’t lock and unlock the door. If playback doesn’t begin shortly, try restarting your device.

Can a dead battery cause a car to not start?

While it isn’t a good idea to just assume the battery is the problem and put a new one in without doing any diagnostic work, a dead battery — or especially a battery that won’t accept a charge — is definitely capable of causing a no-start condition where the lights and radio continue to work to some degree.

How can you tell when your car won’t start but Lights Come On?

Luckily for all drivers, you can tell when your car has blown a fuse. Detecting a damaged fuse is one of the first steps in figuring out what prevents the engine from starting. Analyzing and diagnosing the broken fuse’s location can help you prevent the “car won’t start but lights on” scenario in your vehicle.

Why does my car not light up when I Turn on the ignition?

A good rule of thumb, though, is that if the instrument panel and dashboard do not light up when the key ignition is moved to the second position (between off and on), then there may be a problem with the ignition switch.

Why does my car not start when I Turn on the key?

This feature is not available right now. Please try again later. One possible reason your car wont start is a bad connection. This is one of those things that is often over looked until after the battery or starter or alternator have been replaced or all of the above. if this happens to you check your battery connections. Loading…

What to do if your car won’t start but Lights Come On?

If the battery is dead and not working correctly, you will need to get a replacement or repair the battery. Sometimes, you need to decide if it is better to repair or replace the battery depending on your car’s value, and the cause of the “car won’t start, but lights come on” situation.

Why does my car ignition not start up?

There may be a few reasons why the ignition won’t start the car. Some of them are mechanical (such as a dead battery) and some of them are transponder key related issues. Ignition Cylinder and Car Keys.

Why is my house key not turning in?

A key that doesn’t turn in the lock could have several causes. You may be able to take care of the problem yourself, or you may need to call a locksmith for help. Outdoor locks can collect a lot of dirt and dust inside the lock cylinder. That can cause the pins to get stuck in a partially raised position and prevent the plug from turning.

What to do when your ignition won’t turn over?

Ignition system troubleshooting isn’t too difficult and the first thing to check is your coil. Coil Testing: To properly test your ignition coil, you’ll need a multimeter that can measure impedance. If you don’t have a multimeter, there is an easier test you can perform using simple hand tools. Test your coil and, if it’s bad, replace it.

Why does my car key turn freely in the ignition?

Went to start vehicle, key turned normally, acc power came on but car wouldn’t start. Turned key to off position and acc power stayed on. Key now turns freely in the ignition and the only way to turn off the power is to disconnect the battery.

Why does my car not start when I Turn on the ignition?

One possible reason your car wont start is a bad connection. This is one of those things that is often over looked until after the battery or starter or alternator have been replaced or all of the above. if this happens to you check your battery connections. Loading…

What causes a GMC truck to turn over but not start?

If the engine starts up normally after doing that, it means that fuel pressure is bleeding off and the fuel pump needs to prime the lines before it can start. It can bleed off from one of two places. 1. Fuel pressure regulator has an internal leak, and fuel is bleeding off back to the tank though the return line. 2.

Why is my transponder car key not working?

This chip can be damaged, or the receiver for its signal can stop working. If anything is interfering with the signal between the transponder key and the car immobilizer unit, your car will not start. With two communicating parts, it is important to check both when the car key is not working. You likely have transponder car keys if…

Why does my car key not turn in?

A very common reason a car key won’t turn in the ignition is that the keyway of the ignition cylinder is a little jammed up. Just lubricating the lock may be enough to solve your issue.

Can a transponder key cause a car to not start?

If your key has a large casing on top of it that allows you to open the locks with the touch of a button, then your car has a transponder key. Note how this key could be the reason that your car won’t start, and what to do about it. 1. The key battery is dead

Why does my car key need to be programmed?

Like all computers, the chip inside your transponder key needs to be programmed so that your car’s engine can communicate with it. If you’ve recently had new keys made or are using a spare key of any sort, your key may need to be programmed so it can communicate with your car’s engine.

What should I do if my key fob is not working?

You should also consider that the problem may be with your car itself and not your key fob. You may want to examine the possibility that your car battery has died, which can cause similar issues. Using a spare key fob can be the best way to test whether the problem lies in the key or in the vehicle.

What to do if your car won’t turn on?

Try to use a spare key. If nothing works, your local dealer is the best place to call. If you turn the ignition on and no lights come on at the instrument panel means that there is no power coming from the battery. It could be a dead battery or often a bad ignition switch could cause this.

Why does my car not start when I Turn on the headlights?

It could be a dead battery or often a bad ignition switch could cause this. Turn the headlights on, if they work, means the battery has power, so the problem could be with the ignition switch or wiring between the ignition switch and battery.

What do the dash lights look like when your car won’t start?

Dash lights may look fine, dim, or flicker, if the battery is dead and the car won’t start. Alexandru Stoica / EyeEm / Getty.

What does it mean when my key will not turn in my ignition?

Inspect the key for damage. If your key won’t turn when you insert it into the ignition, it may be because the key has been damaged and no longer engages the correct pins to the depth necessary to spin the cylinder. Examine the key for signs of excessive wear, rounding or broken teeth.

What causes the key not to turn in the ignition?

5 Reasons Your Ignition Key Won’t Turn Bent or Worn Key. This is perhaps the most common cause of the key getting stuck or not turning. Locked Steering Wheel. The steering system has a locking mechanism which is activated whenever you take the key out of the ignition. Jammed Ignition Cylinder. Gear Not Properly Set. Bad Battery.

What if the key won’t go in the ignition?

Ensure the vehicle is in park. Vehicles equipped with an automatic transmission are designed not to start if the transmission is not in park or neutral.
it may be because the key has been damaged and no longer
Ensure there is nothing stuck to the key.

What to do if your key is stuck in the ignition?

If you believe that your key is stuck because of an obstruction in the keyway, lubricate the key and the ignition cylinder. Then use a broken key extractor tool to gently pull your key out. If this method is successful, you should make sure that you clean the keyway of the ignition afterward.

How often should I start my Dodge Dakota?

I have a 1994 Dodge Dakota SLT with the 3.9 V-6. The truck started fine during the spring, summer and fall. Ever since the weather has turned relly cold, it only wants to start about every two to three days. You can start it up, and drive it to hell and back, and it runs just fine… As long as you don’t cut it off…

How can you tell if your starter relay is bad?

The most obvious warning sign that a problem with the starter relay exists is when the vehicle won’t start when you engage the ignition process. As stated above, electronic keys do not have a manual ignition switch. However, when powered, it should send a signal to the starter relay once the key is turned or the starter button is pressed.

What are the problems with a 2006 Dodge Dakota?

Worst 2006 Dodge Dakota Problems #1: Engine Failure 2006 Dakota Average Cost to Fix: $2,100. Average Mileage: 71,000 mi #2: Transmission Makes Noise And Shakes 2006 Dakota Average Cost to Fix: $1,500. Average Mileage: 40,000 mi #3: Transmission Hesitates 2006 Dakota Average Cost to Fix: $2,300. Average Mileage: 92,000 mi

Why does my Ram 1500 not start up?

Turn the key, gauges radio everything but the starter comes on. The trick I found I’d if I hold the ignition switch to the starting position, 15, 30, a minute, sometimes longer, it’ll finally crank over and start. Not sure what’s causing this.

Do you hear a click coming from under the hood when you turn the key. If so does it happen every time you turn the key over or occasionally. If that clicking occurs when you turn the key over and the car starts but when you don’t hear the click the car doesn’t start. . .

Is there a problem with the ignition switch on a Dodge Ram?

Seems to be an ongoing issue with the same defective ignition switch in these vehicles as the Ford, Honda, Acura, Lexus, Toyota, and Infinity that all use the same bad parts. Change the ignition switch and consider yourself lucky you didn’t get cheated by crooked dealerships and dishonest manufacturers. 58 people found this helpful.

Why does my car make a clicking noise when I turn the key?

Most of us have had the unfortunate experience of walking out to our car in the morning, turning the key, and all that happens is click, click, click. Your heart sinks a little. You turn the key back and try again, hoping it will start this time. Sometimes, if we’re lucky, it does.

It’ll turn over or not. And if not, it’s likely a battery or starter problem. And if so, it’s most likely in the car’s electrical or ignition system. Originally Answered: My car won’t start and is silent when turning the key.

Although a clicking sound can come from other sources such as the suspension, the most frequent and familiar clicking comes after turning the key or pressing the ignition button. There might be a sluggish single click or there might be a jarring spray of clicking, and both are symptoms of parts asking for assistance.

Why does my car not start when I open the door?

The dash should light up with all the error/warning lights when in the key is “on” before you start it, or the dome light when you open the door. If the lights don’t come on, the battery is dead, or the main fuse (or wires) not working. If the lights work, but the starter doesn’t turn, then it could be a fuse, wire, or even an ignition problem.

The dash should light up with all the error/warning lights when in the key is “on” before you start it, or the dome light when you open the door. If the lights don’t come on, the battery is dead, or the main fuse (or wires) not working. If the lights work, but the starter doesn’t turn, then it could be a fuse, wire, or even an ignition problem.

Why does my Mercedes not start when I charge the battery?

This Mercedes-Benz is not starting because of a low battery. In this case, what you need to do is trickle charge your battery using any of these 12 volt battery trickle chargers. If you need help read this article on How to charge a Mercedes-Benz the right way. Mercedes won’t start, and it’s not the battery.

What should the voltage of a car battery be when not running?

If loose, tighten the connections. If the noise persists, use a multimeter to test the battery for the correct voltage. A fully charged battery should register 12.6 volts when the vehicle is not running. When the vehicle is running (not possible in this case), it should register approximately 13.7-14.7 volts.

What causes a car battery to not start?

Most auto parts stores will test a battery for free to see if it has enough voltage and cold-cranking amps to start the engine. If the battery passes the test, then it isn’t being sufficiently recharged. That could be caused by corrosion on the battery terminals, or a loose or faulty cable.

If your in any doubt about the correct starting procedure for a lawn tractor, check out – ” How to Start Husqvarna Ride-on Mower”. If you do hear a click sound when you turn the key, check out – ” Mower Wont Start Just Clicks”.

Why does my car not start after I replace the battery?

Evaluating Your Car’s Key Systems for Possible Failure. There are many other possible problems that could lead to the fact that, after you’ve replaced the battery, the car won’t start. One or more of several key systems might not run properly, or there could be a serious malfunction with the electrical system.

To be certain your car is in good condition, you need to turn on your headlights. The battery is in charge of the headlights and dashboard. So, if the headlight comes on while the car doesn’t turn over, then you have a faulty ignition switch. Another probability is that you have a damaged starter.

Why is the BMW key not recognizing the key?

A BMW may show the key symbol on the instrument cluster, PARK light stays on and the engine won’t start if the key is not being recognized. The key may have a slash, line, or exclamation line on top. This problem is because BMW is not recognizing the key which could be due to several reasons as outlined below.

What does it mean when car wont start but Lights Come On?

In plain English this means the ignition won’t attempt to engage the starter motor if the battery is low. A quick way to test your battery is to turn on your car headlights and your windshield wipers at full speed. If the lights seem dim and the wipers are slow, then you can be pretty sure your battery is flat.

Why does my Car Light Go Dim when I Turn on the starter?

Watch the light as you turn the key to the start position. If the dome light goes dim, it suggests power is going to the starter motor and that the starter is probably faulty. (See starter testing below)

All other lights are out. Car won’t start at all when i turned the key to ignition. A low pitched groan also comes from passenger side cabinet after I cycle the key back.

In plain English this means the ignition won’t attempt to engage the starter motor if the battery is low. A quick way to test your battery is to turn on your car headlights and your windshield wipers at full speed. If the lights seem dim and the wipers are slow, then you can be pretty sure your battery is flat.

Watch the light as you turn the key to the start position. If the dome light goes dim, it suggests power is going to the starter motor and that the starter is probably faulty. (See starter testing below)

Why do the lights on my car stop working?

Headlights, your car radio, and most of the electronics in your car draw very little amperage, while a starter can dump a 300+ amp drain on the battery all at once. In fact, you can also run into a situation where the lights will work, but the radio will stop working due to the dead battery, and other even stranger combinations.

What to do if your car wont start when you turn the key?

**FIX** car wont start, delayed, no ignition or sound when you turn the key fix! *Charger shown* – YouTube **FIX** car wont start, delayed, no ignition or sound when you turn the key fix! *Charger shown* If playback doesn’t begin shortly, try restarting your device.

Why does my car not recognize my key fob?

Reasons your car won’t detect the key fob If you try to use the push-button start, but the dashboard message appears that a key is not detected, it could be that the battery inside the remote is dead. the remote itself is broken or no longer programmed to your car.

What’s the best way to turn the key in a car?

Push the steering wheel in the direction that allows a little movement and then insert the key and try to turn the key again. You can put pressure on the steering wheel and also try shaking the steering wheel. As you do this insert the key into the ignition and try to turn the key. DO NOT TRY TO FORCE THE KEY IN THE IGNITION.

If you have this problem you will have to install a new / virgin EIS. You can not install a used unit because the EIS has to be paired / married to the car using Mercedes-Benz Star Diagnostic Software. They key itself may be the reason why the car doesn’t start. The key may open the doors, but it will not start the car.

Push the steering wheel in the direction that allows a little movement and then insert the key and try to turn the key again. You can put pressure on the steering wheel and also try shaking the steering wheel. As you do this insert the key into the ignition and try to turn the key. DO NOT TRY TO FORCE THE KEY IN THE IGNITION.

If you turn the key to the “Start” position, but the engine won’t crank; all you hear is a single click or repeated clicking coming from the engine compartment. Very often this could be caused by a low battery or poor connection between the battery and starter. Check the battery and the terminal cable connections.

Why does my car not start after I charge it?

The easiest one to rule out is the battery, which is why it’s a good place to start. If the battery tests low with a hydrometer, or it fails a load test, then it needs to be charged. If it accepts a charge, and the vehicle starts after it has been charged, then the problem is solved.

While it isn’t a good idea to just assume the battery is the problem and put a new one in without doing any diagnostic work, a dead battery — or especially a battery that won’t accept a charge — is definitely capable of causing a no-start condition where the lights and radio continue to work to some degree.

Why is my car cranking but not starting?

Started up and registered 13ish volts on the dash so I figured the alternator was still working, but possibly the battery was done. So I drove straight home, turned the car off and tried to restart the car but it wouldn’t start, cranked a little but then stopped.

Why is my car battery not starting properly?

As corrosion develops on the ports, the connection consistently grows weaker. There is less metal to metal contact and therefore it becomes harder for power to transfer from the battery to the starter. If you’re having battery problems, check your ports to see if they’re corroded.

Where does the power go from the battery to the starter?

There is a crimp in there somewhere though and I can’t remember if the power goes from the battery directly to the starter of if it jumps through the alternator first… But the grounds. Ground strap under rear seat. Clean all the connections – at battery and chassis. Then do your best to clean all the engine grounds.

What causes a car to not start in Park?

• The starter motor itself or a starter solenoid could be bad. • A problem with a neutral safety switch. If a car doesn’t start with the transmission in Park, but starts in Neutral, it could be caused by a problem with a neutral safety switch or the shifter cable. For example, see this video. Read more about starting system.

Why does my car turn on but won’t start?

If the car clicks when trying to start, but still won’t start, this can be caused by a weak battery, dirty battery terminals, a worn starter motor or a stuck solenoid. Here are a few tricks to try if the car doesn’t start: If your car turns on but won’t start, turn on the dome light and watch it while you try to start the engine.

When did car not start while in Park?

On August 1, car will not start on PARK, all lights on but no cranking. AAA came checked out battery fine. Later car started on PARK. I dropped off the car at Pep Boys

What happens when you turn the key on a car?

The higher rate of electricity gives the starter motor more “oomph” to turn the engine over. The process of starting the car begins at the ignition switch in the driver’s cockpit. The key turn completes a small circuit that tells the battery to release power to the starter solenoid.

if the lights are on and remain on when trying to crank but the problem is that the starter does not even attempt to engage then this points to a problem with either the ignition switch or the exciter cable, this is the narrow gauge cable attached to the starter which, when made live, engages the solenoid to begin the cranking process.

Why does my Hyundai Getz crank but not start?

Check the spark. Without spark to ignite the fuel mix in the combustion chamber, the engine will not start. It will turn over or “crank over” but will never actually run. Spark issues are not limited to the plugs. Check the spark plug wires, the distributor or module, and plug gap.

Why is my Mercedes Benz SLK350 not starting?

If nothing happens when you turn the ignition key to the “Start” position, it means that the starter motor doesn’t turn over the engine. Most commonly this could be caused by a low/dead battery or there is no connection between the battery and starter. Check the battery and the terminal cable connections.

Why does my Car Crank when trying to start?

This only applies when there is a 2 terminal starter solenoid as the bypass wire comes directly off of the ignition switch in that application. The ignition switch fails to make a connection between the 12 volt battery terminal and the resistor bypass terminal on the ignition switch in the crank or start position.

If the battery is dead and not working correctly, you will need to get a replacement or repair the battery. Sometimes, you need to decide if it is better to repair or replace the battery depending on your car’s value, and the cause of the “car won’t start, but lights come on” situation.

Without an adequate charge, a car battery will be too weak to start your vehicle when you turn the ignition key. Modern-day autos always are drawing a small amount of power from the battery, even when the car has been shut off.

What to do if your car loses all power?

Start by checking your ground wires, they run from the battery to the frame, and the engine. look for corrosion in the wires, and at terminal points. Make sure terminal points are not loose. Then also check the positive line to the starter and to the fuse/relay box. again looking for corrosion and loose connections.

What causes a car to lose electrical power?

Check for any loose ground wiring from the cab to the chassis frame and see if they are corroded, damaged, or loose. A bad battery or a loose wire can cause electrical issues within the vehicle.

What happens when a remote key is out of battery?

the most likely was due to your remote key out of battery.replace the batt then things will be normal again.your car’s security immobiliser was activated when the signal was faded. Even if the fob battery is dead, the immobilizer won’t keep the dome/courtesy lights from coming on. The immobilizer will only keep the vehicle from starting.

Start by checking your ground wires, they run from the battery to the frame, and the engine. look for corrosion in the wires, and at terminal points. Make sure terminal points are not loose. Then also check the positive line to the starter and to the fuse/relay box. again looking for corrosion and loose connections.

the most likely was due to your remote key out of battery.replace the batt then things will be normal again.your car’s security immobiliser was activated when the signal was faded. Even if the fob battery is dead, the immobilizer won’t keep the dome/courtesy lights from coming on. The immobilizer will only keep the vehicle from starting.

What to do if your riding mower loses power?

If it does, you have a bad wire grounding out somewhere in your wiring harness. You can run the mower with grounds disconnected from the coils, but it will shut off when you turn the key off, will have to choke it down, but it will start fine by the key.

What happens when you lose all electrical power?

All fine been driving as usual all of last week until today – came back to car, unlocked fine, all power fine and then electrics go completely dead just as I’m turning key to start engine. Thought I was scuppered this time, but then suddenly, again about 5 minutes later, all power came back and I was able to start engine and drive home fine.

So, if this happens the starting motor will have to be replaced. The most common problem with a starting motor is; when you turn your key and nothing happens. A solenoid or motor that has burned out or electrical issues may cause this as well. Furthermore, a dead battery can cause the same problem.

Do you know the signs of a failing starter motor?

Knowing the signs of a failing starter motor, can help you diagnose the problem. When Diagnosing starter motor problems, always start with the battery. So, for your starter motor to work properly, your car battery has to be in; excellent working condition and fully charged.

What happens when the ignition key is turned?

When the ignition key is turned a low amperage electrical signal, is sent to the anti-theft system and computer. The signal then continues to the starters solenoid, which activates the, high amperage side of the electrical system. As a result, engaging the starting motor.

Why does my riding mower click when I turn the key?

If you hear a click when you turn the key, a dead battery, bad starter solenoid, failed starter motor or a seized engine could be the cause. Our riding mower engine clicks but doesn’t turn over video will help you figure out what to fix.

Why does my riding mower not start when I Turn on the ignition?

The starter motor spins the flywheel to start the engine when you turn the ignition key to the start position. If the starter motor runs but doesn’t spin the flywheel, check the starter motor’s drive gear for damage. A defective drive gear won’t mesh with the flywheel teeth to spin the engine.

Why does my car make no clicking sound when I turn the ignition switch?

If the engine is not cranking over and there’s no clicking sound when you turn the ignition switch, the solenoid could be at fault. Put a voltmeter on the solenoid’s terminals and crank the engine.

If your key has a large casing on top of it that allows you to open the locks with the touch of a button, then your car has a transponder key. Note how this key could be the reason that your car won’t start, and what to do about it. 1. The key battery is dead

What to do when your car key fob is not working?

Once the above steps are performed, turn the ignition back to the ‘Off’ position to terminate the programming procedure. Take your key fobs with you and leave the vehicle and close all doors. Test to both unlocks with all your key fobs that got programmed to verify the function.

What does it mean when your car key won’t start?

This is a method to prevent unauthorized keys from starting the car. In other words, keys must be programmed into the car’s computer to start the car. If everything works fine, but the car won’t start, it means that either the key isn’t program or you have the wrong chip value for the key.

What to do when your van won’t start?

Turn the key – single click. So again, we called a tow truck. They called back to get some info and to tell us they were on the way and the van again, magically started. We drove it right to the dealer.

This chip can be damaged, or the receiver for its signal can stop working. If anything is interfering with the signal between the transponder key and the car immobilizer unit, your car will not start. With two communicating parts, it is important to check both when the car key is not working. You likely have transponder car keys if…

Is there a metal key to start the car?

The car has a push to start ignition. There is no metal key. There is no keyed ignition cylinder. Now that we have brushed over some of the differences in car keys, let’s dive right into some of the reasons why your car key might not be working.

If this does not work, rock the steering wheel as you jiggle the key in the ignition. You can mix and match with the methods of turning the wheel and moving the key. As soon as the key turns the steering wheel will unlock, and the car should start. If the key does not turn, then you may have a more severe issue.

Turn the key, gauges radio everything but the starter comes on. The trick I found I’d if I hold the ignition switch to the starting position, 15, 30, a minute, sometimes longer, it’ll finally crank over and start. Not sure what’s causing this.

What to do if your car starts cranking without a key?

I run outside and the start is cranking this time out of no where. Jump in the truck, put in the key turn to on and the truck starts but the starter continues to crank turn off the ignition and the start continues to run pull the positive terminal but only after the battery is fully drained.

Why is my starter cranking without the ignition key?

While putting it in I connected the ground then connected the positive (read different things about which to connect first, please advise) but when I touched the positive terminal to the battery the starter began to crank! Went inside to check and the key wasn’t even in the ignition.

I run outside and the start is cranking this time out of no where. Jump in the truck, put in the key turn to on and the truck starts but the starter continues to crank turn off the ignition and the start continues to run pull the positive terminal but only after the battery is fully drained.

While putting it in I connected the ground then connected the positive (read different things about which to connect first, please advise) but when I touched the positive terminal to the battery the starter began to crank! Went inside to check and the key wasn’t even in the ignition.

When do I go to crank my car the key stays in the start Posi?

Q: When I go to crank my car the key stays in the start position and the car is constantly trying to crank itself. When I place the key in the ignition and proceed to crank the car the key stays in the start position and the car is constantly trying to start itself up but never actually turns over.

Can a bad ignition switch cause a car not to start?

However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems.

So, if this happens the starting motor will have to be replaced. The most common problem with a starting motor is; when you turn your key and nothing happens. A solenoid or motor that has burned out or electrical issues may cause this as well. Furthermore, a dead battery can cause the same problem.

However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems.

Starter stays on after engine started. When you start your engine and release the key or stop pressing the starter button on a modern vehicle, the circuit is supposed to close, which will discontinue power to the starter motor.

Why does my Jeep gauges go crazy with the key off?

JUST NOTICED THAT WITH KEY OFF IF YOU HIT THE WINDSHIELD WIPERS THAT GAUGES WILL MOVE. JEEP DEALERSHIP CAN’T FIGURE IT OUT AND NEITHER CAN MY MECHANIC. MECHANIC THINKS ITS A ELECTRIC PROBLEM? WHAT ABOUT IGNITION? OBVIOUSLY THERE MUST BE SOME JUICE GETTING TO GAUGES WITH KEY OFF. ALSO, JEEP IS IN WON’T START MODE NOW.

JUST NOTICED THAT WITH KEY OFF IF YOU HIT THE WINDSHIELD WIPERS THAT GAUGES WILL MOVE. JEEP DEALERSHIP CAN’T FIGURE IT OUT AND NEITHER CAN MY MECHANIC. MECHANIC THINKS ITS A ELECTRIC PROBLEM? WHAT ABOUT IGNITION? OBVIOUSLY THERE MUST BE SOME JUICE GETTING TO GAUGES WITH KEY OFF. ALSO, JEEP IS IN WON’T START MODE NOW.

What happens if your key is stuck in the ignition?

No power. Key stuck in ignition. Battery good 2011 ram 1500. Turn key, nothing. No power. Key stuck in… My key fob is stuck in the ignition and it wont start the vehicle. It’s a 2011 dodge ram 1500 … read more Ford Motor Company Mast… Key fob stuck in ignition. It can mow. No issues with wear Nothing in the electric things work.

Why is the FOB on my Ram 1500 stuck?

Won’t turn to off position 2014 ram 1500 key fob is stuck. Won’t turn to off position and won’t start … read more Vocational, Technical or Tra…

Why does my Ram key fob not work?

Ram Key fob works but wont start the truck (solved!!!) – YouTube Ram Key fob works but wont start the truck (solved!!!) If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

Bad starter: This should be obvious from the response to the key. If nothing happens at all when you turn the key, the starter may have reached the end of its life. Ignition problem: This could be due to faulty contacts in the ignition switch, or in the wiring. If there is a grinding noise when you turn the key:

Is there a metal key in the ignition?

There is no metal key. There is no keyed ignition cylinder. Now that we have brushed over some of the differences in car keys, let’s dive right into some of the reasons why your car key might not be working. Keep in mind that if your car key is broken, or if you broke your car key off in the lock, the points below will not help you.

Why does my Car Crank when I push the key?

The car used to take 20 times of turning the key to crank. I then figured out that pushing the key in towards the wheel fairly hard and/or wiggling it will get it to crank. When it does crank it turns over and starts fine. I believe it’s a problem with the contacts in the ignition system or something.

Why does my car ignition key not work?

A quick guide to problems and solutions to why the ignition key won’t start the car. Possible reasons and solutions. There may be a few reasons why the ignition won’t start the car. Some of them are mechanical (such as a dead battery) and some of them are transponder key-related issues.

What to do if your car key won’t start?

However, before you assume that there is a problem with the car’s engine or even the starter, you might consider that the key you use to start your car could be at fault.

What kind of turn key makes no sound?

Ltx 1042 turn key makes no sound at all. It just did it One yr old troy bilt riding mower won’t start. Has gas, took One yr old troy bilt riding mower won’t start. Has gas, took battery off and did a slow charge (charged right up).

However, if the headlights continue to burn brightly as you turn the key to start and it still doesn’t start, you have a problem in the electrical feed to the starter. Possibly you have a bad solenoid or a bad starter motor. But don’t give up just yet, there’s one more trick.

What does it mean when your truck won’t start?

So your truck won’t start because it doesn’t have enough power to fully energize the electromagnet inside the starter solenoid. The magnetic field keeps on failing, so the solenoid spring keeps on snapping back. That’s what is making the click-click-click noise you hear.

How does a starter work on a truck?

What’s called the “starter” has 2 power connections – a large wire that provides power to the starter motor, and a smaller wire that powers the starter solenoid. When the key is turned to start the solenoid will engage the gear on the starter with the ring gear on the flywheel as well as trigger the starter motor to begin turning.

These trucks are notorious for ignition switches!! If it’s a bad starter though, you can turn and hold the key in the “start” position, while someone gives the starter a “whack” with a blunt object! It may start, if it does start, you will know that the starter is kapoot!

What to do if your car starter won’t engage?

The battery powers the starter, and if it is not working, the starter will fail to engage completely. Charge your car battery fully, and you can even try to replace the car battery if you have another one you know works.

Why does my starter keep running after I start the engine?

Starter Stays Running, After The Engine Started. When you start the engine and release the key the circuit will, discontinue the power to the starting motor. If this stays on after the engine has started, the main contacts in the solenoid, have most likely failed.

What kind of keyboard keys Start and stop working randomly?

I’m facing an unusual problem , three keys on my laptop keyboard (e , d , 3 ) start and stop working at random. Here is where it gets weird – when one of the keys stop working , all three start working .

Why do I turn the ignition on and off so many times?

Other times I just turn the ignition on and off about 5 or 6 times and it starts. I can detect a pattern to this problem as it seems to come and go. vehicle. If the engine does not crank, then you may have a starter problem. If the engine does not crank, and position, then this is most likely a problem in the Passlock system.

What should I do if my key won’t turn?

The ignition switch needs to have the small linkage from the back side of the key lock cylinder to turn the switch to start and run the vehicle. Have the ignition switch removed and inspect the linkage and switch to see if one or both switch and linkage needs replaced.

Why do I have to turn the key several times before starting the car?

You either have a very clogged fuel filter, or are in need of a new fuel pump. Fuel pressure should be checked, and should be no lower than about 55psi while running or key on. By turning the key several times, you are priming the fuel system up enough to start the vehicle, so you definitely have a fuel issue.

A very common reason a car key won’t turn in the ignition is that the keyway of the ignition cylinder is a little jammed up. Just lubricating the lock may be enough to solve your issue. You will say that WD40 is often the go-to example for lubrication of any kind, but I would not recommend it in this case.

If you cant turn on your headlights or use keyfob to lock unlock your door then battery is completely dead. Another possibility is your security system as the wire from key to starter relay is cut off by the alarm system. 9 lessons from millionaires who are good with money.

Why does my lawn mower make a click sound when I turn the key?

If you do hear a click sound when you turn the key, check out – ” Mower Wont Start Just Clicks”. To test a battery you need a volt meter, but if you don’t have one try this basic check. If your mower has hood lights, or dash lights go ahead and turn them on. If they light up and are bright, your battery is most likely not the problem.

How does battery drain when turning key to ” start “?

Instantly upon turning key to Start, fully charged battery drained to less than 4 volts – either of two batteries. Instantly! With everything off and all fuses and circuit breakers removed, get +9.5 volts between negative pole of battery and ground at alternator mounting frame. Same with either small wire disconnected from battery post on solenoid.

Why does my car battery not work when I start it?

The battery may not be fine. Lights are not high load,so having the lights work is not an indicator of how healthy your battery is Starter motor.

What should I do if I Turn Key to ” start “?

Have someone turn key to start position, check voltage at battery, and see if there is a drop, voltage drop should be minimal, if not there is a direct short somewhere in the ignition circuit, which I doubt because it would blow a fuse, unlss you have an external relay for the starter system. If you get the kill I would suspect relay.

When do you know if your car battery is dead?

After that half-hour, when you are stopped at home or in a safe place, do a little test. After you turn the engine off, wait at least a minute, then start it again. Wait another minute and start it another time or two to make sure that you won’t be stranded at the gas station or wherever you go next.

Why does MY BMW not start when I push the start button?

If your engine does not crank when you push the start button in your BMW, then you may be experiencing one of these problems: There could be a conventional electrical problem preventing your car from starting, such as: A bad starter motor. A failed or damaged starter motor will not be able to crank your engine.

Most auto parts stores will test a battery for free to see if it has enough voltage and cold-cranking amps to start the engine. If the battery passes the test, then it isn’t being sufficiently recharged. That could be caused by corrosion on the battery terminals, or a loose or faulty cable.

What should I do if my car starter is not working?

With someone listening under the hood, activate the starter, and have them listen for a click. If no click, the ignition to starter solenoid is likely the issue. There could be a failed starter, but they usually do not fail suddenly. The make/model/engine for your car would help better guide you to a starting solution.

Why is my electric key fob not working?

The most common culprit behind an electric key fob’s failure is, as you might guess, the battery. This is a relatively easy issue to fix, although you may need to get a ride to get to buy a replacement fob battery.

Why does my starter not make a sound?

Thus if you get zero sound then that means the starter is not trying to turn the engine over at all. Which means air/fuel/spark or even ecu/immobilizer is not your immediate problem. If this was your problem,while the engine may not start, you would at least hear the starter motor turning the engine crank.

Although a clicking sound can come from other sources such as the suspension, the most frequent and familiar clicking comes after turning the key or pressing the ignition button. There might be a sluggish single click or there might be a jarring spray of clicking, and both are symptoms of parts asking for assistance.

What does it mean when your alarm horn does not sound?

Symptom: Horn will not sound (note that the alarm horn is a seperate horn and may still sound even though the main horn will not). Horns not working correctly?

What to do if your car horn does not work?

If your horn does not work with direct power to it them you will need to replace your horn. -If you have a multimeter, disconnect the plugs on the horns and have a friend push on the steering wheel as if they were trying to activate the horn (note: ignition switch must be on).

What to do if your car won’t start?

Get a helper disconnect a sparkplug wire or 2 and ground it to the engine atleast 3/16 away from ground-have helper crank engine over-do you have a snapping blue spark? If so-you have a fuel related problem, Do you hear the fuel pump come On when you turn key on?

Can a PassLock system failure cause a no start?

Passlock system failures are a very, very common cause of no start conditions. OK, the list of possible things that can go wrong looks pretty long but it is rare to see (or have) two different components go bad from two separate systems at the same time.

Why does my car make a clicking noise when I try to start it?

If you hear a clicking noise (but nothing else) when trying to start your car, that means the starter solenoid or relay contacts are operating, but the starter isn’t cranking the engine. My Car Clicks But Won’t Start—What Does it Mean?

Is there a car that won’t start?

Car Won’t Start? Loud Clicking Sound? Always Check this first! – YouTube Car Won’t Start? Loud Clicking Sound? Always Check this first! If playback doesn’t begin shortly, try restarting your device.

Can you start a car with a dead key?

Fortunately, even with the dead key fob, there are two methods that you can use to start your vehicle. INFINITI’s patented Intelligent Key allows you to conveniently unlock your car door and start the engine all without using a key. With the key fob somewhere on your person, you can start your car with the single push of a button.

How can I Fix my Infiniti Intelligent Key?

So the simplest way to fix your Intelligent Key is by opening the key fob and replacing the button cell battery. Then you can easily start your vehicle. In case you don’t have or can’t get a replacement battery, there are two other methods to start your INFINITI car with a dead key.

What should I do if my key is locked in the ignition?

Gently turn the key in the ignition while you slowly jiggle the steering wheel back and forth. If this is the cause of the problem, the key should be able to be move out of the locked position, unlock the wheel, and then start the vehicle.

Why does the ignition not turn on when the car is in Park?

Another reason why the ignition will not go on when your key is inside is because the car may be in another gear. Some vehicles with an automatic transmission do not enable the key to turn unless it is in park or neutral. Make sure you’re in park mode before trying to turn the key. If that doesn’t work, check the battery.

Do you need a metal key to start a car?

Again, this solution only applies to vehicles with a traditional ignition key, meaning a metal key that actually inserts into an ignition switch and turns to start the car. If you’ve got an electronic key , you won’t have this issue.

What does it mean when your car has no lights?

If you have no dash lights or interior lights that means that either your battery is dead or there’s a break in the electrical circuit required to power your car. The test you need to do (or have someone else do) is to check the battery voltage.

The starter clicked a single time when I turned the key, and the lights on the radio came on, but nothing else happened. Several hours later, I attempted to start the truck again, and it started just fine.

The early signs are difficulty in starts before it fails. Most people make the mistake of repeatedly trying to turn the ignition on. Doing so will only lead to more problems. If you are in such a situation, you should not panic. Most starter problems occur in predictable places, and diagnostics are easy to run.

Why is my car not starting when I Turn on the ignition?

You pop into your garage in a hurry, but the car will not start when you turn on the ignition key. You can hear the starter spinning, but it’s not engaging with the flywheel. What could be wrong? Here is a more detailed list of the 5 most common causes why your starter won’t engage.

Press into switch and slightly turn to the right as if starting. Remove finger and now put your key in and turn. The switch is spring toggled when key is in place. Sometimes the spring doesn’t reset. This worked for me. Good luck. 20 people found this helpful. ICONHUSTLE- Did the lights still come on even tho wouldnt start?

What does it mean when your car won’t start with the key?

“MY CAR WON’T START WITH THE KEY” One conversation that comes up every year starts like this: A client calls in a panic and says, “I remote started my vehicle and when I went out to it, the engine shut off and now it won’t start with the key.”

What should I do if my car won’t start?

The ” engine continues to crank after I release the key” is actually normal on most new cars now. Turning the ignition key to the “Start” position, even momentarily- then releasing it, initiates a “start sequence”, which is computer-controlled, and runs the starter for a few seconds on its own.

Why is my Push Button Start button not working?

Often, when a key fob battery becomes weak, the key fob fails to communicate with the car. The solution is to place a key fob close to the start button, like in the photo or if there is a special slot for the key fob, insert it into that slot .

Why does my remote starter not turn on?

You inserted the key in the ignition and thought you turned it to the “on” position, but you did not. You then put your foot on the brake and took the vehicle out of park. The remote starter shut off because you pressed the brake pedal. You instinctively turned the key to start, and nothing happened.

How does the starter motor work on a car?

It starts the internal combustion of your engine. When the battery powers up after an ignition, electric current goes to the starter motor. In the starter motor, pinions move the engine.

Why does the motor just clicks when trying to start?

Cut them off and install new ends or replace the cables if necessary. Corrosiion represents resistance to current flow. Using a voltmeter or test light, have somehone turn the key to START while you measure voltage at the larger terminal on the starter solenoid that feeds the starter.

The car will not start when the ignition is turned all the way over. The battery is fine and I think it is a switch problem. Sometimes I can leave it alone for a few hours and it will fire right up. Other times I just turn the ignition on and off about 5 or 6 times and it starts.

Why is the battery on my Mercedes Benz not working?

Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars. How old is the battery on your Mercedes-Benz?

Is the battery on my Batt fully charged?

My battery charger says my batt is fully charged. The battery is less than a year old, but I had to jump start it about 3 weeks ago. Battery voltage is 12v. Nothing unusual happened yesterday except I washed it. It sat outside for 8 hours after the wash, and then I started it and put it in the garage. It started right up.

When your car won’t crank, won’t turn over, won’t start, and talks back with a single click or rapid-fire click, click, click, click, click, it’s likely the result of an issue with the electrical charging system and/or the starter. These symptoms could spell problems with the wire connections, battery, battery terminals, or alternator.

In other words, you turn the key and nothing happens since the engine won’t turn over. This usually due to a bad starter motor or a bad starter motor solenoid. Remember this article only deals with a no start condition.

How to troubleshoot a Ford 4.9L no start?

Part 1 -How to Troubleshoot a No Start (Ford 4.9L, 5.0L, 5.8L). Troubleshooting a no start problem on your Ford 4.9L, 5.0L, or 5.8L pick up, van, or SUV can be easily done, with the right diagnostic information and troubleshooting strategy and in this article I’ll provide you with some of both.

What causes a car to have no start?

1 The engine pistons and valves (and all the other related components like: timing chains, etc.) are the ones responsible for the induction of the fresh air the engine needs for 2 Although rare, internal engine mechanical problems can and do cause no start conditions. 3 Possible internal engine problems are: Blown head gasket. Blown engine.

Why does my Ford F350 not turn on?

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your F350 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

How do you program a new Ford key?

Once you have a replacement key, the steps you need to take to get it fully programmed are very simple and easy to understand. 1. First you need to open the door and put the vehicle key in the ignition. 2. Next you need to turn the key clockwise from the “off” position to the “on” position.

You could have a bad starter or relay. The starter is responsible for cranking your engine to start it—often as it goes bad it needs more and more power to turn the motor over—so when you turn the key, all you’ll get is a click or nothing. This shows that your battery is operating properly, but your starter isn’t cranking the engine over.

How can I get my Ford F250 to start?

Hook the multimeter to the small ignition switch terminal on the solenoid and have an assistant turn the key, you should get 12 volts. Hook the multimeter to the starter terminal on the solenoid and turn the key again, you should get 12 volts.

What to do if your truck is not starting?

The simplest way to diagnose that problem is to clean the battery terminals and the large starter terminal ( MAKE SURE TO DISCONNECT THE BATTERY + TERMINAL BEFORE DISCONNECTING THE STARTER CABLE OR YOU COULD GET A SEVERE BURN ).

Why does my car not start on the first attempt?

Car won’t start on first attempt, takes several tries the… The vehicle will turn over but will not start until after two or three attempts. When the key is in the ignition and turned all the way to the right and I let go of it it still stays there and attempts to keep starting without me holding the key.

Why do things stay on when the ignition switch is off?

Help would be appreciated. Two things can cause items powered by the key in the ON position to stay on with the key off. 1. First suspect is the IGNITION SOLENOID. Find it. It is “turned on/off” by receiving 12 VDC positive from the ignition switch.

Why is the ACC position on the ignition key not working?

About the ACC position on the ignition key runs those accessories, not to mention that my slides are powered up also not a good situation. Help would be appreciated. Two things can cause items powered by the key in the ON position to stay on with the key off. 1. First suspect is the IGNITION SOLENOID. Find it.

What happens when you turn the key to start a Dodge Caravan?

I have a 2002 Dodge Caravan when I turn the Key to start I get nothing, no lights, no nothing if the key is in the on or off position still nothing, no dash lights no headlights no nothing. nothing also with a battery charger on the battery.

What happens when the key is turned to the on position?

When the key is turned to the on position the relay is switched on and power is directed to the vehicle’s ignition and fuel system components, notably the fuel pump and ignition coils. When the relay fails or has an issue it can cause major problems with the operation of the vehicle.

What to do if your car key does not go off?

Just open the door with the keys in the ignition, look under the dash on the driver or passenger side. using you good hearing locate the chime and simply disconnect the plug from the back. Key fobs do not lock/unlock doors, horn or trunk release.

Is the ignition off but some things stay on?

The problem that I’m having is a little frustrating. The ignition stays powered up after you pull the key out. It does it almost all of the time. The diesel engine will shut down with no problem, but the GPS, blower fan, wipers and, at times, the cruise control will not function. And “yes” to the answer to your question.

About the ACC position on the ignition key runs those accessories, not to mention that my slides are powered up also not a good situation. Help would be appreciated. Two things can cause items powered by the key in the ON position to stay on with the key off. 1. First suspect is the IGNITION SOLENOID. Find it.

Why is my 2003 Ford F-150 not starting?

There are a number of issues that can go wrong with starting system and make your 2003 Ford F-150 car won’t start or hard time to start – This article guides you through some of the facts behind the starting system, and the components that may be to blame, and tells you what action you can take to try to remedy each situation.

What to do if your Volkswagen Passat won’t start?

Replace starter solenoid, starter contacts, starter assembly or repair starter circuit as required. If you turn the key to the “Start” position, but the engine won’t crank; all you hear is a single click or repeated clicking coming from the engine compartment.

If you turn the key to the “Start” position, but the engine won’t crank; all you hear is a single click or repeated clicking coming from the engine compartment. Very often this could be caused by a low battery or poor connection between the battery and starter. Check the battery and the terminal cable connections.

There are a number of issues that can go wrong with starting system and make your 2003 Ford F-150 car won’t start or hard time to start – This article guides you through some of the facts behind the starting system, and the components that may be to blame, and tells you what action you can take to try to remedy each situation.

If nothing happens when you turn the ignition key to the “Start” position, it means that the starter motor doesn’t turn over the engine. Most commonly this could be caused by a low/dead battery or there is no connection between the battery and starter. Check the battery and the terminal cable connections.

Why does my Honda S2000 not start up?

If nothing happens when you turn the ignition key to the “Start” position, it means that the starter motor doesn’t turn over the engine. Most commonly this could be caused by a low/dead battery or there is no connection between the battery and starter.

Can a 12V battery be used as a starter?

Like this one http://www.etrailer.com/static/images/pics/D/W/DW00254_2_1000.jpg Connections should be pristine. A battery can read 12 VDC, even 13+ VDC and however have not enough amps for the strong twist the starter demands, or just too weak to maintain the charge for a starter.

If there’s no power to the starter motor but power everywhere else you’d hear a “click!” noise when you turned to start but nothing else – ie. no whirring or cranking noises.

What should I do if MY Volt won’t start?

Except if the battery is dead and the car won’t start, not sure if the odb adapter will give you any info. If the car is awake enough to unlock via the door buttons, OBD is active for many PIDs, including 12V voltage. (It does not need to be started and in ‘ready’ state)

Why does my car not start when I jump the solenoid?

If your car won’t start and the problem is not caused by a dead battery, then you might need to jump the starter solenoid to get your car moving again. The starter solenoid is responsible for sending an electrical current to the starter motor.

What happens when you push the start button on a car?

When you turn the key or push the Start button, the engine should start and the circuit that controls the starter motor should close. If the starter remains ON even if the engine is already running, then this might mean that the main contacts of the starter solenoid are welded together in the closed position.

How to start a car with a bad ignition switch?

Jumper cables Open the hood of your car and locate the ignition coil and the battery. Then using a jumper cable, connect the positive terminal of the battery to the positive side of the coil. This will give power to the dashboard which is needed to start the engine.

If your car won’t start and the problem is not caused by a dead battery, then you might need to jump the starter solenoid to get your car moving again. The starter solenoid is responsible for sending an electrical current to the starter motor.

What causes a car to have a no start problem?

A blown fuse in the starter circuit could be the cause of a no-start problem. Broken or corroded wiring – Damaged or dirty wires to the battery or to the starter solenoid (or wires that are loose) can prevent sufficient power from reaching the starter.

Can a blown fuse cause a starter to not start?

Blown fuse – Sometimes the simplest explanation is the best one. A blown fuse in the starter circuit could be the cause of a no-start problem. Broken or corroded wiring – Damaged or dirty wires to the battery or to the starter solenoid (or wires that are loose) can prevent sufficient power from reaching the starter.

When you turn the key or push the Start button, the engine should start and the circuit that controls the starter motor should close. If the starter remains ON even if the engine is already running, then this might mean that the main contacts of the starter solenoid are welded together in the closed position.

If you hear a clicking sound, this often means the electrical components are not working. However, if there is no sound at all, and especially if you see the dashboard lights or dials come on when you turn the key, this often means the engine simply won’t even try to start since it’s not getting that needed signal from the key.

What to do if your car wont turn over but has power?

To determine why your car won’t turn over but has power, you need to disconnect the cable from your engine and let the engine run for 30 minutes to see if the alternator can charge the battery and power the car.

What is the objective of the starter motor?

The objective of the starting motor is to rotate the engine between 85 and 150 rpm’s. Basically There Are Two Main Parts In Every Starter; The primary motor; that turns your crankshaft and starts your engine.

When do I need to replace my starting motor?

The two components inside the starting motor, that commonly fail are the solenoid or the starting motor itself. So, if this happens the starting motor will have to be replaced. The most common problem with a starting motor is, when you turn your key and nothing happens.

Why does my Car start when I turn the key?

When you turn your key, an electromagnet forces the starter gear to engage the teeth on your flywheel. The motion of the starter gear sliding forward into the flywheel also engages electrical contacts which give power to the starter motor, spinning the starter gear and starting your engine.

The two components inside the starting motor, that commonly fail are the solenoid or the starting motor itself. So, if this happens the starting motor will have to be replaced. The most common problem with a starting motor is, when you turn your key and nothing happens.

What do you need to know about starter motors?

Starter motors are used to rotate an engine to, begin the starting process. But, for a engine to start, many things need to happen, simultaneously and in rapid succession. For the engine to fire, one of the most important factors is turning of the flywheel.

When the ignition key is turned a low amperage electrical signal, is sent to the anti-theft system and computer. The signal then continues to the starters solenoid, which activates the, high amperage side of the electrical system. As a result, engaging the starting motor.

Why is there no crank and no dash lights?

No crank and all the dash lights turned off. Now, when you turn the key there is no resistance like you normally feel when the ignition and starter are about to engage and none of the lights on the dash turn on and there is no crank. Assuming it is something in the ignition/starter assembly that is wrong.

Why is my car not working when I Turn on the ignition?

It turns out that the tab that sticks out of the bottom of the lock cylinder that is part of the metal lock/ignition housing has snapped. It is the thing that sticks out of the bottom of the lock cylinder and inserts into the back of the ignition switch. This little metal tab literally broke.

No crank and all the dash lights turned off. Now, when you turn the key there is no resistance like you normally feel when the ignition and starter are about to engage and none of the lights on the dash turn on and there is no crank. Assuming it is something in the ignition/starter assembly that is wrong.

Why does my car not turn over when I Turn on the ignition?

If you press this button or if you turn the key on a manual ignition switch and the vehicle does not turn over, it may be caused by a problem with the starter relay. This problem may be attributed to a circuit that has failed, so no matter how many times you turn the key, the vehicle will not start.

What are the symptoms of an ignition switch failure?

Careful car owners can recognize the symptoms of ignition switch failure before the problem leaves them stranded on the side of the road. An ignition switch performs several functions for a vehicle.

Can a bad ignition key cause a car to stall?

The cylinder may become stripped or damaged resulting in the starter key no longer fitting, or the key being unable to lock into the drive position. Problems with the lock cylinder may be intermittent with the position slipping while the car is operating which will cause sluggish acceleration and stalling.

Why is my Pats key not working on my car?

Devices that power up the PCM without powering up the PATS Control module can experience no-start concerns. Items such as foil stickers, brass key tags, other PATS keys, and other transponders used to purchase gasoline or other metallic objects can cause interference with the PATS key.

The cylinder may become stripped or damaged resulting in the starter key no longer fitting, or the key being unable to lock into the drive position. Problems with the lock cylinder may be intermittent with the position slipping while the car is operating which will cause sluggish acceleration and stalling.

Careful car owners can recognize the symptoms of ignition switch failure before the problem leaves them stranded on the side of the road. An ignition switch performs several functions for a vehicle.

Do you need to reprogram ignition keys for Pats?

Erasing and reprogramming ignition keys does not cure any known intermittent PATS no-start issues. Do not reprogram keys if a fault cannot be identified. Always verify that there are no aftermarket devices causing interference, such as alarms, remote starters or other devices utilizing transponders.

There are several reasons why this can happen, but if you turn the key and the engine does not even turn over, you have already eliminated some of those reasons: poorly tuned engine, empty gas tank, etc. When the starter does not even turn the engine, the problem is most likely in the electrical system or…

Why does my car starter not turn over?

Problem: Starter does not turn or turns over slowly when key is turned. Solution #1: Check the rest of the electrical system for the correct voltage, grounds, and wiring. Often, the starter is misdiagnosed as the culprit for electrical system problems when the problem really lies in some other area of the system.

Why does my starter dim when I turn the key?

If they dim when you turn the key to start, then voltage is being sent to the starter motor but either the starter solenoid is not engaging or the starter motor has failed. In this case, you will need to remove the starter motor/solenoid assembly and have it tested at an auto parts store.

Car Engine Doesn’t Turn Off When Removing Key or Pressing STOP It is a strange problem to have a car that won’t turn off when you remove the key from the ignition or press the Engine Stop button. Your engine will continue to run even when you remove the key from the ignition because the fuel pump is not shutting off.

Why does my starter not stop when I start the car?

But now a new, seemingly-related problem has begun. When I start the van, the starter motor doesn’t stop. It stays engaged and keeps trying to start the already-running engine. If I turn the key to the off position, the engine will stop firing but the starter keeps working.

What to do if your starter won’t start?

Clean all connections both at the starter and the battery to ensure there is no bad connection. You can often locate bad connections by feeling on the cable connection; it will create a lot of heat if there is a bad connection. You can identify the flywheel as the large wheel that is located between the engine and transmission.

Can a car have lights but no starter?

As 2002c230 notes, you can have lights but no starter. Call mb roadside assist (I think you may still have access, they just changed the rules) and they’ll come out and try to jump it properly.

When do you know if your car starter is bad?

There are a few known symptoms of a starter that is not engaging. Here are some of the most common ones. This is the most obvious sign of a bad starter. When a person turns on the ignition and electrical signal is sent to the starter relay.

What should I do if nothing happens when I turn the key?

Make sure that the car is in park or neutral. The engine won’t crank with the transmission in any other position. If you have a stick shift, make sure the clutch pedal is pushed to the floor. Turn your ignition on, then turn on the headlights. Check their brightness.

Make sure that the car is in park or neutral. The engine won’t crank with the transmission in any other position. If you have a stick shift, make sure the clutch pedal is pushed to the floor. Turn your ignition on, then turn on the headlights. Check their brightness.

What causes a Ford F-150 engine to turn off?

5.4 Triton Engine Failure of the Fuel Pump Driver Module This problem is typical for the Ford F-150 with a 5.4 Triton engine. Failure of the fuel pump driver module usually cuts off the petrol feed to the engine which, of course, causes the engine to turn off, thus cutting power to all essential systems.

Is it possible to damage a Ford key?

Like we mentioned earlier, the Ford’s keys are strong, sturdy, and well-made. However, there could be damage to the key or its in-built chip. If neither method works, try them with a second key that you might have of the car.

Where are the fuses located in a Ford E-350?

The fuse panel is located below and to the left of the steering wheel by the brake pedal. The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.

Can a bad ignition switch cause a car to not turn over?

The vehicle will not be able to turn over because the electrical wiring in the electric switch isn’t able to communicate with the battery, and the vehicle’s accessories will function poorly (lights dim or not working). Problems in the vehicle’s lock cylinder will impact the driver’s ability to insert the starter key into the lock housing.

Where is the relay module on a Ford e-250?

The instrument panel relay module is located behind the radio in the center of the instrument panel. The engine compartment relay module is located in one of two places depending on which type of engine your vehicle is equipped with: Gasoline engine: driver side of the engine compartment above the brake master cylinder.

Is there a way to turn off the power button?

To do this, go to Settings > Scheduled power ON/OFF, and set the options of “Power on” and “Power off”. There is seldom known fact: you can remap the functionality of a physical button to another, by programming or an app like Power Button to Volume Button. To resolve the problem perpetually, you’d better do some programming, i.e. the ADB way.

What happens if the ignition switch is off all the time?

If both large lugs have power all the time, even if you have the key off and remove the small signal wire, the solenoid is bad. 2. If, however, that small signal wire has power (12 VDC positive) all the time, you have a problem in the ignition switch or wiring.

Is there a way to restart my phone without the power button?

If your phone is still on, then you can easily take the assistance of various readily available applications to replace the usage of the power button. Afterward, you can easily restart the phone without the power button by substituting its action with any other key (like volume or camera key).

Why does my car not start when I change the battery?

Our professional locksmiths have seen many cases where changing the car’s battery results in erased keys, meaning the computer no longer recognizes the older keys that used to work just fine. Moreover, installing an alarm may result in the same as well as changing the ignition cylinder.

What does no start no crank no click mean?

If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that. In the old days, power flowed through the ignition switch and down to the starter solenoid. Not anymore.

Why does my car not crank when I start it?

This way when it’s time to fire up the vehicle the battery can be charged, tested and installed. If the vehicle will not crank when the battery is known to be good, we won’t have to backtrack and check it again. When it comes to vintage cars and batteries the biggest problem is when unexpected long-term storage occurs.

Automotive Forums .com Car Chat > Chevrolet > Avalanche | C&K | Silverado | Suburban | Tahoe > Silverado > Turn key and no start/crank…bat is good! Turn key and no start/crank…bat is good! Hi guys, Thanks in advance for any help, I have a 01 2500HD Crew cab with the 6.0. Tonight I stopped at the gas station to grab some milk.

Instantly upon turning key to Start, fully charged battery drained to less than 4 volts – either of two batteries. Instantly! With everything off and all fuses and circuit breakers removed, get +9.5 volts between negative pole of battery and ground at alternator mounting frame. Same with either small wire disconnected from battery post on solenoid.

Have someone turn key to start position, check voltage at battery, and see if there is a drop, voltage drop should be minimal, if not there is a direct short somewhere in the ignition circuit, which I doubt because it would blow a fuse, unlss you have an external relay for the starter system. If you get the kill I would suspect relay.

On starters with the solenoid on top (GM, most others) the solenoid grounds through the starter brushes, so when the brushes make bad contact you get the “silent treatment” when you turn the key. The small wire going to the starter solenoid should get 12 volts or so when the key is turned to “start”.

Do you have to have transponder key to turn on ignition?

Non-transponder key and a transponder key, that have the same keyway (meaning both will turn the ignition on but one won’t start the car since it isn’t a transponder key). You must make sure that if your car is transponder equipped, you have a transponder key.

What does it mean when Your starter clicks but wont start?

Today’s topic is “starter clicks but won’t start.” Here are the steps to check that you got a faulty starter. Number one. First start by checking for battery power. Turn on your headlights, and if the light is bright that means you got power. If it is not bright then you got a bad battery or a faulty alternator.

Why does my starter click when I turn the key?

It sounds like power is getting to the starter because I can hear a loud click when I turn the key. I’ve researched the topic thoroughly on this site but no one has seemed to have the same problem. In all the other cases there is click coming from the starter. Any help greatly appreciated. Thanks

Why does my car battery click when I start it?

Loose battery terminals Loose battery terminals on the car battery are another common problem. Someone could cause it by forgetting to tighten these properly after a reparation, and the contact between the connectors and the terminals becomes bad.

Why does my riding mower make a clicking sound when I turn the key?

So what’s the problem with a riding mower that won’t start just clicks? The most common reason for a clicking sound on a riding mower when you turn the key, is a flat battery. Other possible reasons include: Flat/Faulty Battery Dirty / Loose Battery Connection Faulty Solenoid Binding Starter Motor Excessive valve lash Hydro-locked Engine

What to do when your car clicks when trying to start?

Also, check the connector at the starter and the car battery to make sure the cable connector bolts are tightened and have a good connection. Feel on them after you have been cranking for a while, and make sure they are not warm. If they are warm, there is a bad connection there which needs to be cleaned.

In a no crank condition, the engine is not cranking when you turn the key to crank the engine. In other words, you turn the key and nothing happens since the engine won’t turn over. This usually due to a bad starter motor or a bad starter motor solenoid. Remember this article only deals with a no start condition.

What causes no start on a Ford pick up?

If no voltage is present, as your helper cranks the engine, then the cause of no fuel condition is due to either a bad fuse, fuel pump relay, or inertia switch. One of the most overlooked areas, when testing a hard to diagnose no start, is the mechanical condition of your 4.9L, 5.0L or 5.8L Ford car, pick up, van or SUV.

In other words, you turn the key and nothing happens since the engine won’t turn over. This usually due to a bad starter motor or a bad starter motor solenoid. Remember this article only deals with a no start condition.

Part 1 -How to Troubleshoot a No Start (Ford 4.9L, 5.0L, 5.8L). Troubleshooting a no start problem on your Ford 4.9L, 5.0L, or 5.8L pick up, van, or SUV can be easily done, with the right diagnostic information and troubleshooting strategy and in this article I’ll provide you with some of both.

How can I tell if my car won’t start?

One of the most overlooked areas, when testing a hard to diagnose no start, is the mechanical condition of your 4.9L, 5.0L or 5.8L Ford car, pick up, van or SUV. Checking the engine mechanical condition means an engine compression test.

This is because 9/10 a no start condition will be because of a bad battery, bad connections, or user error in diagnosing those both. I have started many friends cars that wouldn’t crank, or crank strongly, simply because I saw the battery terminals were loose.

You could have a bad starter or relay. The starter is responsible for cranking your engine to start it—often as it goes bad it needs more and more power to turn the motor over—so when you turn the key, all you’ll get is a click or nothing. This shows that your battery is operating properly, but your starter isn’t cranking the engine over.

Why does my Ford F250 not turn on?

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your F250 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

How can I tell if my Ford F250 is starting?

Hook the multimeter to the starter terminal on the solenoid and turn the key again, you should get 12 volts. On many of these trucks you don’t need to jack it up to reach the starter, so you can perform the same test by connecting to the starter itself and checking for 12 volts when the key is turned.

What happens when a starter goes bad on a Ford F250?

When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your F250, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it. There are a lot of issues that can cause your F250 to crank, but not start.

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your F250 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

Hook the multimeter to the starter terminal on the solenoid and turn the key again, you should get 12 volts. On many of these trucks you don’t need to jack it up to reach the starter, so you can perform the same test by connecting to the starter itself and checking for 12 volts when the key is turned.

When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your F250, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it. There are a lot of issues that can cause your F250 to crank, but not start.

Why does my car not start when I crank the engine?

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

What does it mean when your car key won’t turn?

If the car’s battery is dead, you will often notice that the key won’t turn. This isn’t unusual in higher end vehicles, which frequently use more complex electronic ignition systems. Check the life of your battery to verify this. Oftentimes, the problem is not with the related components of the car, but with the vehicle key itself.

If nothing happens when you turn the ignition key to the “Start” position, it means that the starter motor doesn’t turn over the engine. Most commonly this could be caused by a dead battery; here is How to check the battery. If the battery checks out OK, but the starter still won’t crank, there could be a number of possible reasons.

Why does my F150 battery not turn over?

This wire will only have power to it in the crank position, provided that the ignition switch and clutch switch are functioning correctly! The other two larger battery wires that are attached deliver battery voltage from the battery to the starter when the signal post receives power!

What causes a Ford F-150 key to not turn?

What are common reasons my Ford F-150 key won’t turn? While there are a variety of reasons your Ford F-150 key won’t turn, the most common 3 are a binding steering column/lock, an ignition switch issue, or a problem with the ignition key.

Sometimes I have to turn the key a few times before it starts. Other times, more and more frequently, I sit in the hot Florida sun turning the key repeatedly, often for over five solid minutes. When this happens, with each turn of the key, there is no click, no sputter, no turnover of any type.

What does it mean when your truck wont start?

When it will not start the lights, stereo, etc. will come on but the engine will click and not turn over. Other times it will start right up. By the way the truck runs just fine once started. I can jump start it every time problem is I cant find a hill to get it to roll start every time.

Why does my starter click when the key is turned on?

Hope this helps!!! Nope it’s not a dead battery the starter sounds like it wants to go but all it does is click. it almost sounds like what my old s10 did when the starter is over heated. what does a starter go for?

https://www.youtube.com/watch?v=4eTZr5rpUA0

Dash lights may look fine, dim, or flicker, if the battery is dead and the car won’t start. Alexandru Stoica / EyeEm / Getty.

What to do if your truck has no power?

Start by cleaning all the battery terminals. That way you know there is power that far. Then turn on the key and then jump the starter solenoid on the passenger fender. What you need to do is pull off a small wire and jump the heavy leads to that small terminal. I just use a screwdriver to make the jump.

Why does my Truck turn over but won’t start?

There are many potential engine issues when your truck turns over but won’t start indicating that your engine is not getting enough fuel, doesn’t have the appropriate compression or is not receiving fuel. Sources for this problem vary, starting with the ignition system’s issues to problems with the fuel supply system.

Why does my car not start without fuel in it?

While this might be obvious, your engine won’t start without fuel in your tank, and many people start panicking and searching for potential culprits when their fuel tank is empty. Even if your fuel gauge is showing some fuel in the fuel tank, this gauge might malfunction for various reasons.

What to do if your GMC Sierra won’t start?

Let sit for awhile, turn key, won’t start, turn key off, turn key again, starts up and runs great. A week later, same issue. I went to work everything great, went to go home, wouldn’t start. Tried to turn key a few times, won’t start, let sit about 15 min., turned key, started up. Stop to get gas 15 min. later, wouldn’t start. Stranded for 2 hours.

What to do when Your Truck turns over but won’t start?

Check your fuel tank When your truck turns over but won’t start, the first thing you need to check before any troubleshooting is your fuel tank. While this might be obvious, your engine won’t start without fuel in your tank, and many people start panicking and searching for potential culprits when their fuel tank is empty.

While this might be obvious, your engine won’t start without fuel in your tank, and many people start panicking and searching for potential culprits when their fuel tank is empty. Even if your fuel gauge is showing some fuel in the fuel tank, this gauge might malfunction for various reasons.

To determine why your car won’t turn over but has power, you need to disconnect the cable from your engine and let the engine run for 30 minutes to see if the alternator can charge the battery and power the car.

When does the anti theft system car wont start?

If the engine does not respond or dies immediately after cranking up, leave the key in that position for 10 minutes. When the security light goes off, turn the ignition off, wait 20 seconds, and then start the engine. These are the most popular ways to solve the problem of anti theft system car wont start.

What happens when I Turn on the ignition?

I have a 2006 Ford Focus and I recently replaced the battery. Everything comes on dashboard, lights, radio, etc. Then when I turn the key to ignition the lights kind of flicker and then nothing! Everything goes dead, I tried turning the key again after that happens and nothing all dead.

What causes no start on a Ford 5.8L?

Go to: No Start 2: Checking Fuel. CASE 2: Spark was NOT present in all of the cylinders A number of things can cause this no spark result. So this what I would suggest:

What can I use to fix my car key that wont turn?

Purchase canned air from a local retail or office supply store and insert the straw from the nozzle directly into the key hole. Spray the canned air into the key hole in short spurts. It should only take a few short sprays to clean out any debris. Do not spray the entire can into the key hole.

In a no crank condition, the engine is not cranking when you turn the key to crank the engine. In other words, you turn the key and nothing happens since the engine won’t turn over. This usually due to a bad starter motor or a bad starter motor solenoid. Remember this article only deals with a no start condition.

What makes a Ford 4.9L engine not start?

Without spark, the engine will crank but not start. Ignition control module (ICM). Depending on the year of your specific Ford, it’ll have a inner-fender mounted ignition control module or a distributor mounted ignition control module.

What’s the difference between no start and no crank?

Since a lot of folks confuse a no crank condition with a no start condition, I’ll clear it up right now: In a no start condition (also known as a cranks but does not start) your vehicle’s starter motor is cranking the engine but the engine is not starting.

What to do when your Ford key does not work?

Leave it in “on” until the light stops blinking. Set your foot on the brake and turn the key to start the car. The Intelligent Access (IA) key system from Ford is designed to make it easy to get in your vehicle and go without digging through pockets or purses for your keys.

What to do if your F450 truck wont turn?

Try starter solenoid or battery. If okay go to main dealer. If the LED illuminates for 4 seconds and the engine cranks but does not start, PATS is working correctly and the fault lies elsewhere. Check the Fuel Cut-Off switch.

What to do if your Ford FOB does not work?

Check your fob battery to make sure that it does not need replacement. If your battery dies, you can use the center console to “read” the key even without a good battery. Try using your secondary key to start the car. Do not use the backup key as it will only open the doors and the glove box.

What to do if your Ford starter won’t start?

If the reading is less than 12 volts, charge the battery and attempt to start the vehicle again. If the starter still does not kick in, move on to the next step. Turn on the headlights of your Ford then turn the key in the ignition. If the headlights dim, the ignition switch is sending power to the starter. In this case, move to the next step.

Why does my Ford F350 not start on its own?

If your battery no longer has enough charge to turn the starter, your F350 will not start. As a battery ages, it’s “cranking amps” decrease, leaving it with a diminished capacity for starting the vehicle. When this happens, you’ll often hear the vehicle crank slowly, but not start.

The Car Starter. Your starter is vital to your car because it is responsible for starting the engine. The battery sends it a jolt of electricity, which the starter uses to turn the engine over and get it to start. A broken starter will make a clicking sound when you turn the key. The car won’t start, but the dash lights are on.

Why does my car not start when I jump the alternator?

If jump starting gets your engine started and running, but the car will not start again once you turn it off, the battery is probably the problem. In this case, the alternator is doing its job of keeping the battery going once it has been jumped, but the battery can’t hold a charge when the alternator is shuts off.

When to replace battery, alternator, or starter?

When you check these three, always start with the battery. It’s most often the part that failed, and it’s also the cheapest part to replace. A car battery should last about four to five years. It is not made to hold a charge for that long, so it gets recharged by the car’s alternator while you drive.

How can I tell if my car starter has failed?

Signs the Starter has Failed: A broken starter will make a clicking sound when you turn the key. The car won’t start, but the dash lights are on. Jump starting your car or truck does not turn over the engine at all.

The Car Starter. Your starter is vital to your car because it is responsible for starting the engine. The battery sends it a jolt of electricity, which the starter uses to turn the engine over and get it to start. A broken starter will make a clicking sound when you turn the key. The car won’t start, but the dash lights are on.

Can a bad alternator cause a car not to start?

The alternator could have failed and the battery charge was all used up by the time the symptoms started. If your battery can be charged and the car starts, if the alternator is bad the batter will draw down again in a matter of hours or days, depending on your usage.

When you check these three, always start with the battery. It’s most often the part that failed, and it’s also the cheapest part to replace. A car battery should last about four to five years. It is not made to hold a charge for that long, so it gets recharged by the car’s alternator while you drive.

Signs the Starter has Failed: A broken starter will make a clicking sound when you turn the key. The car won’t start, but the dash lights are on. Jump starting your car or truck does not turn over the engine at all.

Can a Ford F-150 start with a dead battery?

There is a hidden compartment in every F-150 vehicle where you can place key fob and it will start your vehicle, it does not matter it has dead battery or even if there is no battery inside. You just have to place the original key inside this secret location.

Our professional locksmiths have seen many cases where changing the car’s battery results in erased keys, meaning the computer no longer recognizes the older keys that used to work just fine. Moreover, installing an alarm may result in the same as well as changing the ignition cylinder.

Where is the ignition key on a Ford F-150?

You just have to place the original key inside this secret location. After placing the key in the small compartment at the bottom of the cup holder in the center console, continue to press the push start button. The vehicle will then start without any problems.

What to do if your Ford car won’t start?

Therefore, if the car is winding over, but not firing up, then you can be certain you don’t have a Ford car key problem. However, if it won’t even try and start, then the key is worth looking at. There is an immobiliser light on early Fords. It’s always red and it’s normally a red dot, or a red padlock symbol.

What should I do if my Ford truck won’t start?

The best way to deal with this issue is to jump your truck using jumper cables, then drive it around for at least 15 minutes. Now with the truck running, use the multimeter again and test the voltage, which should be over 13 volts at idle. If you rev the engine, the volts should go up. If that checks out, your charging system is working okay.

Hook the multimeter to the small ignition switch terminal on the solenoid and have an assistant turn the key, you should get 12 volts. Hook the multimeter to the starter terminal on the solenoid and turn the key again, you should get 12 volts.

Why does my Ford truck won’t start?

Figure 4. Piston and rod from a hydro-locked motor. If the motor cranks but the truck won’t start, go to Step 4. It could be fuel starved. The 1980 to 1996 covers both carburated and fuel injected trucks, but they all still need air, fuel, and spark to run.

Why is my 2011 Ford F-150 not starting?

There are a number of issues that can go wrong with starting system and make your 2011 Ford F-150 car won’t start or hard time to start – This article guides you through some of the facts behind the starting system, and the components that may be to blame, and tells you what action you can take to try to remedy each situation.

Use the FastC method described above to start checking to make sure you have fuel, air, spark, correct timing, and compression. If you do not feel comfortable taking apart pieces of your car or working around gasoline and sparks please just have the car towed to a mechanic.

With someone listening under the hood, activate the starter, and have them listen for a click. If no click, the ignition to starter solenoid is likely the issue. There could be a failed starter, but they usually do not fail suddenly. The make/model/engine for your car would help better guide you to a starting solution.

What to do if your starter solenoid does not work?

Usually there is a fusable link or a large fuse for the starter solenoid. With someone listening under the hood, activate the starter, and have them listen for a click. If no click, the ignition to starter solenoid is likely the issue. There could be a failed starter, but they usually do not fail suddenly.

Usually there is a fusable link or a large fuse for the starter solenoid. With someone listening under the hood, activate the starter, and have them listen for a click. If no click, the ignition to starter solenoid is likely the issue. There could be a failed starter, but they usually do not fail suddenly.

If you can see the starter motor, tap on it firmly, but not with deadly force. Then try turning the key again. If still no luck, you can have somebody hold the key on start while you tap on the starter. Many times, that will jar a bad starter motor loose and make it start the engine.

Why does the ignition key stay in the ” start ” position?

Automatic column shift with cruise. When I start the truck, the key will stay in the “start” position. I have to manually turn it back to “run” so my starter won’t keep running. Also, when I turn the truck off, I now have power to accessories (radio, wipers, lights), just like I have the key turned to accessory.

What happens when you put a new battery in a car?

In some cars, it can last for as long as a decade without any repairs or maintenance. However, if the alternator does fail, the car can still run for a limited time on just battery power. Unfortunately, once the alternator stops charging, you will find that your car won’t start after a new battery has been installed.

What to do if your car battery won’t start?

If the replaced battery car won’t start, the first thing to check is whether you replaced the battery correctly. Are the cable clamps tight? Are the cables themselves in good shape?

You’ve come to the right place, and you’ll be cutting grass shortly. So what’s the problem with a riding mower that won’t start just clicks? The most common reason for a clicking sound on a riding mower when you turn the key, is a flat battery.

If the replaced battery car won’t start, the first thing to check is whether you replaced the battery correctly. Are the cable clamps tight? Are the cables themselves in good shape?

How to reset the anti theft system in a Ford?

1 Insert the key into the ignition and turn it on to the position where the accessories are activated but not the engine. 2 Leave the key in this position for at least 10 minutes. 3 Check the anti-theft light again. 4 Now try to start the engine. 5 Repeat the process at least a couple of times if it does not work the first time.

Why is my Ford Crown Victoria not starting?

If the engine’s ability to fire the spark plug at the right time is called “timing”. If the plugs are firing at the wrong time, or something has happened to cause the camshaft to no longer be in sync with the crankshaft, your Crown Victoria won’t start.

What happens if you have a classic car that won’t start?

One of the downsides of owning a classic car is they sit for long periods of time. As we head towards the automobile with the key in hand, we often wonder if she will fire up or not. Professional mechanics divide a no start condition into two main categories. There is the scenario where the engine spins over nicely but refuses to start.

What causes a car to crank but not start?

One of the biggest issues that causes a vehicle to crank but not start is ignition issues. When there is no spark, the engine will not start. You’ll probably have a misfire related code such as P0300, P0301, etc….. Ignition issues can be caused by many things, including bad spark plugs, bad coil packs, bad plug wires, computer issues, and more.

Why does my car make a whirring sound when I turn the key?

Without sounding too technical on the details, the starter solenoid is responsible for interlocking the pinion gear from the flywheel when you turn the key to start the engine. The whirring sound is caused by a worn or bad solenoid since the pinion gear is spinning the armature but is unable to start or crank the engine.

What are the symptoms of a bad starter?

Symptoms of a Bad Starter on a Ford Truck 1 Click. When the ignition key is turned to the start position and nothing occurs except a rather loud and heavy-sounding click noise, the starter may be seized up. 2 Motor Without Engine. The gear in the nose of a starter is known as a bendix. 3 Grind Aftershock. 4 Lock Up. …

Without sounding too technical on the details, the starter solenoid is responsible for interlocking the pinion gear from the flywheel when you turn the key to start the engine. The whirring sound is caused by a worn or bad solenoid since the pinion gear is spinning the armature but is unable to start or crank the engine.

Can a bad ignition switch cause a Lucerne not to start?

A bad ignition switch can cause your Lucerne not to start at all. And, it can keep your Lucerne from starting in a couple of different ways. The first is when the starter cranks, but the bad ignition switch doesn’t turn on the fuel pump or ignition. The engine will just turn over with no spark.

What happens when I Turn on the dash lights?

It comes on solid for about 5 seconds after the key is turned on then goes off. Yes it does. I just noticed that after it sits awhile it takes about 10 seconds after i turn the key for the dash lights and radio to come on. That all looks OK.

Do you have a test light when I turn the key?

Yes it does. I just noticed that after it sits awhile it takes about 10 seconds after i turn the key for the dash lights and radio to come on. That all looks OK. Just feeling around on the other relays the only one clcking is the run/crank relay when the key is turned on. Do you have a test light?

Why does my car make a clicking sound when I turn the key?

The most common reason for the clicking sound when you turn the key is a flat battery, other possible reasons include: Yes, it’s a long list, but you won’t have to check all of them, I’ll bet your problem is one of the first three, I have listed the likely causes in order of commonality.

You’ve come to the right place, and you’ll be cutting grass shortly. So what’s the problem with a riding mower that won’t start just clicks? The most common reason for a clicking sound on a riding mower when you turn the key, is a flat battery.

The most common reason for the clicking sound when you turn the key is a flat battery, other possible reasons include: Yes, it’s a long list, but you won’t have to check all of them, I’ll bet your problem is one of the first three, I have listed the likely causes in order of commonality.

Basically, with a fully charged battery, and with the key held in the “start” position, the starter is either getting power or it isn’t. With the key in the “start” position, if the starter motor is getting power but the starter doesn’t work, then the starter is condemned and replaced.

When your car’s engine won’t start and all you hear is a rapid clicking noise, you’re likely to mutter, “Darn” (or perhaps another four-letter word) and instantly think that something is wrong with the battery. You would probably be right.

Where is the starter on a car that won’t start?

To figure out why your car won’t start, it helps to know the difference between the starter and the ignition switch. The starter is an electric motor that cranks the engine, effectively starting the car. It is under the hood, usually on the passenger side at the bottom of the motor next to the transmission.

This only applies when there is a 2 terminal starter solenoid as the bypass wire comes directly off of the ignition switch in that application. The ignition switch fails to make a connection between the 12 volt battery terminal and the resistor bypass terminal on the ignition switch in the crank or start position.

To figure out why your car won’t start, it helps to know the difference between the starter and the ignition switch. The starter is an electric motor that cranks the engine, effectively starting the car. It is under the hood, usually on the passenger side at the bottom of the motor next to the transmission.

Q: When I go to crank my car the key stays in the start position and the car is constantly trying to crank itself. When I place the key in the ignition and proceed to crank the car the key stays in the start position and the car is constantly trying to start itself up but never actually turns over.

Inside the relay, a set of electrical contacts allows current to flow to the starter solenoid. If these contacts become corroded or extremely worn, they may not get the job done. An external starter solenoid, unlike the relay, carries high voltages.

Is there a fix for Ford no key detected?

Ford No Key Detected fix! – YouTube Ford No Key Detected fix! If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

Why does my Mercedes Benz engine not start?

However, when i turn the key all the way, the engine does not even try to crank. It almost feels as if only the starter is disconnected or something from the car entirely. (I know nothing about car engines)

What kind of car engine does not crank?

However, when i turn the key all the way, the engine does not even try to crank. It almost feels as if only the starter is disconnected or something from the car entirely. (I know nothing about car engines) I drive a 2004 C230 sedan.

Why does my old car battery not crank?

If the vehicle will not crank when the battery is known to be good, we won’t have to backtrack and check it again. When it comes to vintage cars and batteries the biggest problem is when unexpected long-term storage occurs. Sometimes we park our classics expecting to use them in the near future.

What to do when your car won’t crank?

The engine won’t crank with the transmission in any other position. If you have a stick shift, make sure the clutch pedal is pushed to the floor. Turn your ignition on, then turn on the headlights. Check their brightness. If they are dim (or not working at all), chances are the battery is dead and you’ll need a jumpstart.

The engine won’t crank with the transmission in any other position. If you have a stick shift, make sure the clutch pedal is pushed to the floor. Turn your ignition on, then turn on the headlights. Check their brightness. If they are dim (or not working at all), chances are the battery is dead and you’ll need a jumpstart.

How can I tell if my car starter is going bad?

Don’t worry quite yet. If you’re at home, there are three things you can test that will tell you what’s wrong—and you might have an inexpensive repair on your hands. The most likely problem is a dead or drained battery. If that’s good, then your battery cables might be dirty or your starter may be going bad.

What does Esc key do when I restart my laptop?

11-05-2012 08:22 AM When i RESTART my laptop [pavilion dv6c16nr] it says that press ESC KEY TO START UP MENU but when i press esc/escape key nothing happens pls help me solve this problem. thanks a lot to this site and more power!:) Solved! Go to Solution.

Why does my 2008 Ford Escape not start?

My 2008 Ford Escape won’t start. When the key is put into the ignition, the electrical devices work, windows, dash 2008 Ford Escape: wont start..electrical..windows, dash lights… No power to ssolenojid. Car died in parking lot shut it off Ford Senior Master Technic… Vocational, Technical or Tra… It appears to be locked out.

Why do I hear a click when I start my car?

If you get a single fairly loud click when you turn the key to “start”, but the starter doesn’t “ turn over “, you may have a bad starter solenoid. A solenoid is just a switch which is operated by electricity.

How can you tell if a car key is the problem?

This prevents someone from “hot-wiring” the car, or trying to start it by connecting ignition wiring under the steering column or forcing it to start with a screwdriver or fake key in the ignition. How can you tell if the problem is the key?

What happens when your car starter is not working?

Bad Starter: When you put your key in the ignition to start your car it’s the starter that gets the engine going. It transfers the power from your battery to the engine which allows the vehicle to get going. When your starter is not working, you’re not going to get a crank in your engine.

What to do if your ignition light is not working?

If wiring is not overheated, flood the ignition switch with switch cleaner or WD40 and likewise the local multi-plug connector. You might also be able to locate the source of the problem by wriggling the local connections mentioned whilst operating the switch.

The ” engine continues to crank after I release the key” is actually normal on most new cars now. Turning the ignition key to the “Start” position, even momentarily- then releasing it, initiates a “start sequence”, which is computer-controlled, and runs the starter for a few seconds on its own.

There are many potential engine issues when your truck turns over but won’t start indicating that your engine is not getting enough fuel, doesn’t have the appropriate compression or is not receiving fuel. Sources for this problem vary, starting with the ignition system’s issues to problems with the fuel supply system.

Non-transponder key and a transponder key, that have the same keyway (meaning both will turn the ignition on but one won’t start the car since it isn’t a transponder key). You must make sure that if your car is transponder equipped, you have a transponder key.

How do you reprogram a car ignition key?

First, you must verify that the key you have is a transponder key AND has the right value AND reprogram the key by an automotive locksmith or dealer. Below, two keys.

What’s called the “starter” has 2 power connections – a large wire that provides power to the starter motor, and a smaller wire that powers the starter solenoid. When the key is turned to start the solenoid will engage the gear on the starter with the ring gear on the flywheel as well as trigger the starter motor to begin turning.

Why does my car click when I Turn on the starter?

However, a broken wire between the ignition lock and the starter will in the most cases not cause a clicking noise. If the cable is broken, nothing will happen when you are turning the ignition lock. The most common problem is a faulty car battery when it comes to cars that click when turning the ignition.

I have a 2006 Ford Focus and I recently replaced the battery. Everything comes on dashboard, lights, radio, etc. Then when I turn the key to ignition the lights kind of flicker and then nothing! Everything goes dead, I tried turning the key again after that happens and nothing all dead.

Why does my car battery not turn on?

Since trying to jump the car didn’t work, I think the problem isn’t with the connection between the battery cables and the battery. Given that, the most likely place to start looking is where the battery cables attach to the car. Follow the cables and check the condition of the “other” end of the cables, if I’m right, one will be loose or corroded.

Why does my Ford F250 diesel not start?

They could not be functioning. The diesel engine doesn’t have spark plugs like most trucks, instead, it used glow plugs, which are designed to heat up and assist in starting the diesel engine. Although the glow plugs aren’t always essential for starting, they assist the process especially when the ambient temperature is very low.

What to do if your Ford F250 won’t start?

Clean the terminals and reconnect the batteries. Examine the cables for signs of internal corrosion. Check the ground connection from the battery cable to the chassis. Check the positive battery cable connection to the solenoid, and starter. Figure 1. Ford F250 is equipped with two batteries.

When did the Ford F250 diesel engine come out?

This article applies to the Ford F250 and F350 diesel engine (1994-2003). Trying to start your Ford truck and getting nothing can ruin your whole day, and make work on the job site grind to a halt.

What to do if your diesel truck won’t start?

Disconnect the negative (black) terminal on both batteries (otherwise you can’t test them individually). Test the voltage on each with your multimeter set to DC volts. Each battery should read over 12 volts. If one reads low, replace it. If both check out, one or both may still be bad and not able to deliver the proper power under a load.

Thus if you get zero sound then that means the starter is not trying to turn the engine over at all. Which means air/fuel/spark or even ecu/immobilizer is not your immediate problem. If this was your problem,while the engine may not start, you would at least hear the starter motor turning the engine crank.

Why does my Allison Transmission key not work?

Get a flash on the shift gear display on the key turn. Then dark. Dash gauges act normal. Sounds like a ground problem check and clean the chassis ground.

What happens if you don’t jump start your car?

If your battery has a physical problem with it, as in the case is broken or it was damaged in some way, then a jump start will not repair the battery. If it’s completely frozen, you don’t want to even jump start at all as that can cause your battery to explode.

Why does a car not start with a broken starter?

Your starter is vital to your car because it is responsible for starting the engine. The battery sends it a jolt of electricity, which the starter uses to turn the engine over and get it to start. A broken starter will make a clicking sound when you turn the key. The car won’t start, but the dash lights are on.

Why does my car not start after a jump?

When your starter stops working, it can’t “crank” the engine to get it started. Clicking or grinding sounds are clues that your starter might be the reason your car won’t start after a jump.

What does no crank no start car mean?

Mechanics refer to this as a no crank no start condition. Of course, the number one reason for an engine not the crank on any car would be a problem with the battery. Since classic car owners are familiar with how to treat a battery during long-term storage we’ll just touch on this briefly and then move on.

Where does the 12 V go in a no crank car?

With the ignition key in the on position, there should be power on the heavy gauge red wire and a strong ground on the black wire. When the ignition key is pushed to the crank position you should have an additional 12 V going into the relay and 12 V comes out on the wire that runs to the starter solenoid.

Why does my Mustang crank but won’t start?

If timing is too far advanced or retarded, this can cause hiccups upon startup. Ignition timing needs to be up to par as well. If the ignition timing is too far off then this can cause your starting problems as well. Everything we have covered so far has to have the spark to complete it all. Without spark, you will never have a running engine.

Why is the ignition timing off on my Mustang?

If the timing is off, there can be many different problems. If you have recently installed a camshaft or other valvetrain related components, you may want to go back over your install. If timing is too far advanced or retarded, this can cause hiccups upon startup. Ignition timing needs to be up to par as well.

What’s the best way to start a Mustang?

One quick way to start off with is to just pull a plug wire or coil and ground it out against the engine. This way you can physically see the spark if it is firing. As we mentioned earlier in the timing section, ignition timing has to be set correctly for the engine to start.

What causes a car to start but not start?

The ignition system normally has many different parts that can be the culprit. Distributors, coils, plugs, wires, sensors, computers, and the list can go from there. Your proper firing order will need to be correct. If not, then this can cause a no-start condition.

Why is there no power when the key is turned?

When that dead/dying battery was in place, the lights would power on dimly while the key was on, and I would hear a clicking sound while trying to start it, but it would not turn over. The battery was tested and needed to be replaced. Now, with a new battery that has been tested to be good, I don’t get any electrical power when turning the key.

Why does my ATV have no power when I turn the key?

When I installed the new battery, I didn’t noticed that there were two positive cables that need to be connected to the positive terminal. One of them had slipped back into the boot, and I only connected the other one. This is why the ATV had no power at all when I was turning the key.

What happens when I turn the key to CR?

If they are dim (or not working at all), chances are the battery is dead and you’ll need a jumpstart. Turn the key to III and check to see if the headlights dim. If they don’t, it means there’s a problem with the ignition or the starter. If they do dim (or go out), the problem lies with the battery.

What happens to a car battery when it is shut off?

Keeping electronic items plugged in and operating, even after the car has been shut off, can drain a car battery enough to prevent it from starting the engine again later. A car battery might lose some of its charge for other reasons.

What to do if your ECM power relay is failing?

For this reason, if you suspect that your ECM power relay may be having an issue, have the vehicle inspected by a professional technician, such as one from YourMechanic, to determine if the relay should be replaced. The most popular service booked by readers of this article is Vehicle Engine Electrical Inspection.

Can a car battery be drained when the engine is off?

Keeping electronic items plugged in and operating, even after the car has been shut off, can drain a car battery enough to prevent it from starting the engine again later. Other Sources of Trouble A car battery might lose some of its charge for other reasons.

Why does my car engine not turn off when I remove the key?

Your engine will continue to run even when you remove the key from the ignition because the fuel pump is not shutting off. This problem is typically caused by a faulty fuel pump relay or a defective ignition switch. In this article, we take a look at why your engine won’t turn off when removing the key and what you can do to stop the engine.

What does it mean when your car won’t turn off?

It can be very frustrating when it doesn’t. If the engine continues to run just as before you turned it off – as if you hadn’t turned it off at all – your ignition and fuel system are not shutting down. In that case, your car has an electrical problem that needs to be addressed.

Why does my car stop when I press the stop button?

On vehicles equipped with the Start/Stop convenience feature, the engine may not stop when you press the STOP button. A defective Push Start button can cause this problem. If the button stops working, it may need to be replaced.

How is the solenoid connected to the key?

It’s usually cylindrical, about 1-2 inches long and has a single wire connected to it. That wire is hot when the key is on and opens the valve, allowing it to close when the key is off. Disconnect the wire and turn on the key. Touch the connectors together and release them. You should hear the solenoid click as it opens and closes.

Why does my car engine not want to start?

If the engine still doesn’t seem like it wants to start, probably fuel is getting into the cylinders and your problems lies somewhere else. However, if the engine runs momentarily and dies, then the problem is that fuel is not getting to the cylinders. Check for a clogged fuel filter, or a bad fuel pressure regulator.

Why does my Chevy Truck start and idle?

Not sure why this test caused a better and longer gas flow than the above test of just putting the ignition in the ON position and seeing how much gas comes out of the line before the fuel filter. Last test says to start the vehicle and remove the relay.

What should I do if my GMC Sierra won’t start?

GM Mechanic: FIXITMAN, Master Technician replied 12 years ago Okay. You need to first see if there is power going to the relay from the vehicles computer. If there is then the relay is the problem. If there is not then there is a problem in the circuit. Start by checking to see if the vehicle will start if you put it in nuetral.

What causes a GMC Sierra 1500 key to not turn?

What are common reasons my GMC Sierra 1500 key won’t turn? While there are a variety of reasons your GMC Sierra 1500 key won’t turn, the most common 3 are a binding steering column/lock, an ignition switch issue, or a problem with the ignition key.

Is there a GMC Sierra that won’t start?

I have a 2010 GMC Sierra 2 door pick up that won’t start ans is saying to service theft deterant system. I replaced the battery and the truck started and ran fine. No it won’t start again. Any ideas?

Can a unworn key turn an ignition cylinder?

Or, an unworn key may not turn a worn ignition cylinder, as they haven’t “worn together.” How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders.

Why does my car not start in cold weather?

Car won’t start in cold weather. If the engine is flooded, holding the pedal down (the throttle plate open) while you crank will pull a lot of air through the cylinders and remove the excess gas. When the mixture is close to right and the spark plugs are no longer too wet to fire, the engine will start.

If this does not work, rock the steering wheel as you jiggle the key in the ignition. You can mix and match with the methods of turning the wheel and moving the key. As soon as the key turns the steering wheel will unlock, and the car should start. If the key does not turn, then you may have a more severe issue.

Why does my car not start in the winter?

Winter weather is tough on cars, and on their drivers. The temperature drops below freezing and you have to deal with snow, sleet and slush. Then, to top it all off, you get in one chilly morning and turn the key, only to find your vehicle won’t start. What are you supposed to do?

What kind of truck won’t start in cold weather?

Discussion in ‘ General Truck Info ‘ started by duckandbuck, Dec 11, 2011 . My 93 suzuki carry won’t start………. We are having a some cold weather here in OK for the past week and i have been working on my truck trying to figure out its sputtering.

What should I do if my car won’t start in the Cold?

Keep your vehicle warm. Starting with a car that is at above-freezing temperatures will eliminate just about all of these cold-weather starting problems. If you have a heated garage, use it. Even an unheated garage can help, and if you use it safely, a small electric or kerosene heater can fend off the cold.

Why does my car not start when I turn the key?