Why does my 2005 LLY Duramax not start?

– Fixya Duramax won’t start! My 2005 LLY duramax became hard to start a few days ago. Then today it wouldn’t start at all. Turns over but wont start. The fuel filter primer loses pressure after priming it.

What should I do if my check engine light is still coming on?

Put the keys in your ignition and turn your ignition on and off consecutively after a second in each step. Once it is done, see if the engine check light is still coming on or not. If the check light is off, you are ready to go, but if it is still coming on, get ready by reading the codes with a scanner instead. Let it Go Off Itself

What causes a fuel injector to stop working?

Over time the nozzle of the injector can become dirty and partially blocked. When you shut off your engine the injector will, soak up the heat of the engine. This causes any fuel left in the injector to evaporate, leaving behind hard deposits, inside the injector. Over time, these will eventually block the injector.

What’s the number on the glow plug on Duramax?

The only code showing up is a number three glow plug, but that code has shown up on and off for a while, and shouldn’t make it impossible to start. Clicking this will make more experts see the question and we will remind you when it gets answered.

What’s the Check Engine light on a Duramax?

Started up fine. Only thing i noticed was that the oil pressure was pegged out at 120 and the battery was around 10 or 11 marker on the gauge. Ran and drove fine. Keep in mind the temp was around 18F this morning when i left for work. You will need a scanner to pull the codes.

Are there any problems with the LLY Duramax?

In terms of LLY injector problems, GM had sorted out the internal failures with the 2004 ½ redesign, but the LLY Duramax would occasionally exhibit a trouble code for the injectors, but in most cases it turned out to be an issue with the injector harness rubbing through and causing a short or open in the wiring.

Why is my Duramax diesel engine not working?

The trucks computer keeps track of how much fuel needs to be added or subtracted from each individual cylinder to make the engine run smoothly, and this value is called the balance rate. If one cylinder is contributing too much or not as much as the rest, the cause is usually a bad injector and the cure is a replacement.

Where is the CP3 injection pump in a Duramax?

The CP3 injection pump sits in the valley of the engine between the cylinder heads and is driven by the camshaft gear, and it has two main jobs: get fuel from the tank up to the engine, and pressurize the fuel to 26,000psi and ultimately inject it into the engine.

When did the first Duramax V8 engine come out?

Duramax Engine LB7 2001 to 2004 The first Duramax V8 was introduced in 2001 and was given the code name LB7. The introduction of common rail injection powered by the Bosch CP3 injection pump made the LB7 Duramax stand apart from other diesels of the day with excellent power and efficiency.

Can you get an oil change on a Duramax?

Yes, you can do most of the maintenance yourself: oil changes, fuel filter changes, air filter, tire rotations, etc. The Duramax V8 holds 10 quarts of oil. The extra oil and the fuel filter add cost to the equation. Getting the oil change done at a dealership or a shop will run $100 at a minimum.

Are there any issues with the Duramax fuel pump?

The new injectors available from us and others are updated and do not have the cracking issue. Fuel Filter Housing Oring Leaks – The Duramax fuel system does not have any sort of low pressure fuel pump pushing fuel to the engine from the tank. The injection pump sucks all the fuel from the tank.

What to do if your Duramax cooler goes bad?

Lastly we replace a fair amount of glow plug controllers as well. You will usually get a diagnostic trouble code for the cooler when they go bad. Head Gaskets – As these truck reach the 100,000-150,000 miles we are seeing more and more head gasket issues. The Duramax has a multi-layer steel head gasket.

What causes a fuel filter to leak on a Duramax?

Fuel Filter Housing Oring Leaks – The Duramax fuel system does not have any sort of low pressure fuel pump pushing fuel to the engine from the tank. The injection pump sucks all the fuel from the tank.

What are the problems with a Duramax diesel engine?

Both of these issues result in fuel leaking from the injector which can then enter the crankcase. This can lead to more serious problems, as diesel fuel doesn’t offer the same lubrication properties as oil. You’ll also experience loss of power, excessive smoke, rough idling, and engine misfiring.

Can a leaking O ring cause a Duramax to hard start?

If you’re going to own an LB7 Duramax over an extended period of time, the odds are you will experience this problem. A leaking o-ring not only results in a fuel leak, but air can also enter the fuel system. This causes various performance issues, hard starts, and even engine codes.

What causes a Duramax crankcase to leak fuel?

The ball seat can deteriorate over time, resulting in an incomplete seal, and ultimately, injector leaking. Both of these issues result in fuel leaking from the injector which can then enter the crankcase. This can lead to more serious problems, as diesel fuel doesn’t offer the same lubrication properties as oil.

Why did my 2004 Duramax engine not start?

My 2004 Duramax started and then died like it was out of fuel. Now it won’t start. I have about 1/4 tank of fuel, tried priming it until the batteries died.

Why did my Chevy Duramax lose power under load?

Follow diagnostic chart, test system pressure, relief valve failed” so they replaced the FPRV. More limps and a year later there was a P0101 code indicating the Mass Air Flow (MAF) sensor failed so I had it replaced. The air filter was changed then too.

How many versions of the Duramax diesel engine are there?

All told, there are six different iterations of the Duramax diesel engine: LB7, LLY, LBZ, LMM, LML, and L5P spanning from 2001 to the present day. Each version of the engine has its own issues and quirks, and some are less problematic than others.

Are there any major problems with the L5P duramax?

Mechanically, the L5P Duramax is stout and very few major problems have been reported. One common problem is with the MAP sensor however, as it tends to clog with soot and throw a check engine light, but a simple MAP sensor spacer and a can of electrical cleaner can get you back on the road worry free and prevent the soot from building up again.

What happens when a Duramax engine goes down?

Not only does this mean game-over for the engine, but it results in a truck that’s down for weeks (if not months) and a huge chunk of change missing from your wallet. The failure is most common in higher horsepower engines, but can still occur in moderately modified and even stock power plants.

Which is the best 6.6 Duramax engine to buy?

Just like the LBZ was the best pre-emissions 6.6 Duramax engine, the L5P is the best post-emissions Duramax. All the problems associated with emissions system and injection pump have been taken care of, and for 2017 GM switched suppliers of the injection pump from Bosch to Denso.

What was the code name for the Duramax in 2011?

In an effort to keep up with the ever-tightening emission regulations, GM redesigned its Duramax for the 2011 model year, and this time the code name was LML.

Are there any problems with the Commons 6.6L Duramax Diesel?

Common Problems with the 6.6L Duramax Diesel. The 6.6L Duramax has been in production since 2001 and has proved, on a large scale, to be a relatively reliable and durable platform. While various versions of the engine have surfaced over the years, all generations of the Duramax are based on the same foundation.

What should I do if my Duramax won’t start?

Very slight. Drove 5 miles, had dinner, came out, crank but no start. Held throttle down and still no start. Checked prime, fuel squirted out of vent when loosened. Cranked and held throttle down, started after about 10 seconds.

Are there any issues with the Duramax primer button?

Under the primer button there are some orings that fail on a regular basis. This can produce long cranks and hard starts. Glow Plug System Issues – Nearly half of the check engine lights that come in for the Duramax pickups are for glow plugs.

Are there any problems with the Duramax engine?

The failure is most common in higher horsepower engines, but can still occur in moderately modified and even stock power plants. Not specific to one version of Duramax in particular (ex: LB7, LLY, LBZ, LMM or LML), the problem exists across all generations.

What was the problem with the LBZ Duramax in 2006?

Glow plug failure was a concern on the 2006 model year LBZ and LLY Duramax models, but the problem should have been long corrected for owners of these years. The concern was that the glow plug module would over cycle the glow plugs, creating a scenario in which the tip of the glow plug could actually deform and/or break off in the engine.

Are there any problems with the Duramax LMM?

One problem can rear its head when you are pushing the power of the LMM to a level GM never imagined, and that’s with the pistons. Simply put, they can crack under pressure. There are a lot of factors which dictate the power level where a piston bites the dust, but it’s usually north of 600 horsepower.

In an effort to keep up with the ever-tightening emission regulations, GM redesigned its Duramax for the 2011 model year, and this time the code name was LML.

Why does my 04 LB7 engine not start?

Now engine wont start anymore. Went to start my 04 LB7 this morning to let it warm up before going to work. As I shut the door and walk away, the engine died. I tried to fire it back up but it just spins over and doesnt start. The truck has 144k, has about 3.5k on new injectors installed by dealer, fuel filter was replaced around the same time.

What causes a truck to start then die?

Click to expand… The fuel filter head issue will cause it to stop after its been running, the problem is usually pronounced when your parked on a hill. My filter head is bad and my truck does the same thing, truck starts then dies, pump the pumper, then it fires and all is glorious.

What to do if your Duramax crankshaft is weak?

The ultimate fix for the weak factory crankshaft is to replace it with a stronger unit that’s been internally balanced. The billet Callies crankshaft available through Wagler Competition Products is machined from triple heat treated 4330V steel and features reduced rod journal widths for improved strength (which calls for narrower rods).

How can I Keep my Duramax Diesel pump healthy?

However, there are measures you can take to keep the pump happy and healthy, the first being to always buy your diesel from a high-traffic, reputable filling station that’s known to dispense good, clean fuel. Second, always change the fuel filter at or before the recommended service interval.

Why does my 2005 Chevy 2500 HD not start?

My 2005 Chevy 2500 HD won’t start. Engine won’t turn over with key at all. Batteries are hot. You can take a power probe and shoot 12v to starter solenoid wire and it will crank and run fine. I traced that wire back to the fuse panel under the hood on the driver’s side. There is a CRANK fuse as well as a starter relay in that panel.

Why does my Chevy Duramax not turn over?

Engine won’t turn over with key at all. Batteries are hot. You can take a power probe and shoot 12v to starter solenoid wire and it will crank and run fine. I traced that wire back to the fuse panel under the hood on the driver’s side. There is a CRANK fuse as well as a starter relay in that panel.

Where is the crank fuse on a 2005 Chevy Duramax?

I traced that wire back to the fuse panel under the hood on the driver’s side. There is a CRANK fuse as well as a starter relay in that panel. When you turn the key to start, the fuse gets 12v but the starter relay is not getting voltage to the solenoid wire. Also noticed that the tow/haul button isn’t working and it was before the issue.

What causes a Chevy Silverado to not start?

There are really two main ways that a vehicle will not start. The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your Silverado won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

When to take your GMC Duramax to the dealership?

It’s hard to pinpoint what the problem is without running more tests and the only way to run those tests is with the computer the dealership has. Just so you know your injectors are still under warranty until 100,000 miles. Most likely you will have to take it to the dealership to get you truck fixed.

What causes a car to start but not keep running?

The engine requires the right amount of air and fuel to mix together for ignition. If there is a fuel leak somewhere, then the correct amount of fuel may not make it to the combustion chamber. This might be enough to allow the engine to start, but not keep running.

Can a bad starter relay be a solenoid problem?

Sometimes the starter itself is the problem. Electrical issues can be annoying and inconvenient. They can also be hazardous and can cause damage. If you run into symptoms of a bad starter relay or solenoid with your car, truck, or SUV, make sure to have a trusted technician to diagnose the specific problem.

Are there any problems with my 2003 Duramax?

Thaks for the help. injectors,water pump,headgaskets,injectors again,instrument cluster,steering shaft,pinion seal,and injectors again. I have on 03 with 66,000 on it and know problems. Friend of mine has 03 asmost same truck and know problems with 145,000 on it. Sure love mine. P:S Injectors should be warrantied to 200,000.

When to submit a repair order for a 2003 Duramax?

Claims with repair orders prior to May 25, 2004 must be submitted to the Service Contract provider. For 2003 vehicles covered by Vehicle Service Contracts, all eligible claims with repair orders on or after October 10, 2006 are covered by this special policy and must be submitted using the labor operation codes provided with this bulletin.

Can a Duramax diesel engine be kept warm?

Huge no-no for modern diesel engines as your grid heater in the intake and glowplugs stay on until the truck is “warm”. Also sometimes rebuilding the filter head isn’t enough, you have to replace it. Click to expand… Yeah I wasn’t to fond of spraying it.

How to stop a Duramax truck from losing Prime?

Tried running fuel line from injection pump to tank of diesel.. No go Pressurized the fuel tank primed it and tried starting.. Nothing Pressurized fuel tank sprayed soap water on lines.. No leaks found Tried having someone prime while I cranked. Truck will run off starting fluid through airbox but dies when you stop spraying.

Why did my truck engine shut off going down the road?

That was because the top started to rust out, not from failure. When it went in my 98, I was out hunting and it died driving down the road. Replacing it on the truck wasn’t bad, I didn’t even attempt it on the Yukon. Try crawling under the truck and whack the fuel tank with a rubber mallet while someone tries to start it. Click to expand…

What to do if your car won’t start?

If so then it is a fuel issue, it will not throw any codes for that so your taking a chance of wasting time/money. If it fires then either drop the tank or lift the bed up, check for power/ground as these were noted for harness problems at the module. If you have power/ground then replace the module.

Is there a crank fuse on a Duramax?

Batteries are hot. You can take a power probe and shoot 12v to starter solenoid wire and it will crank and run fine. I traced that wire back to the fuse panel under the hood on the driver’s side. There is a CRANK fuse as well as a starter relay in that panel.

Why is the tow / haul button not working on my Duramax?

When you turn the key to start, the fuse gets 12v but the starter relay is not getting voltage to the solenoid wire. Also noticed that the tow/haul button isn’t working and it was before the issue. Any suggestions? swap the relay with another in the box and see if the relay is the problem. 5 people found this helpful.

What happens if the crankshaft on a Duramax goes bad?

Perhaps the most devastating of all Duramax failures is a broken factory crankshaft. Not only does this mean game-over for the engine, but it results in a truck that’s down for weeks (if not months) and a huge chunk of change missing from your wallet.

Why is my generator not starting after a month?

If you didn’t drain the carburetor before putting your generator away for a month or more of storage, this is likely the culprit for why you’re having starting issues now. Old gasoline will form clogs in the carburetor, making it impossible for new fuel to get through.

Can a Duramax engine crank but won’t start?

Drove home 5 miles. came out several hours later, engine cranks normally but won’t fire. Held throttle down and it started. Had slight surging. Very slight. Drove 5 miles, had dinner, came out, crank but no start. Held throttle down and still no start.

Is the Dodge 2500 hard starting when cold?

2003 dodge 2500, 5.9 4×4. Hard to start when cold, replaced fuel heater and fuel filters. If the outside temp is about 5 celsius, it will not start unless the block heater is on for an hour. This is t … read more

Can a 2003 Cummins have a hard start?

One of the most common calls we get are from customers with a 2003-2007 Cummins that have developed either a hard start or no start condition. In order to help out, we had our very own Tyler Lucas, put together this step by step tutorial that you will hopefully find insightful.

What causes a ram truck to not start?

First off, let’s get this out of the way, Ram trucks NEVER had the best luck with lift pumps. A lack of lift pump flow will not only cause a no start issue, but depending on how it failed, can cause other issues that we will discuss further into this post. The factory lift pumps on the 2003-2007 Cummins produce a dismal 10-11.5 PSI at idle.

What makes a Duramax LB7 diesel so special?

The introduction of common rail injection powered by the Bosch CP3 injection pump made the LB7 Duramax stand apart from other diesels of the day with excellent power and efficiency.

Why does my vertical top load washer not start?

Vertical modular top-load washers signal a component problem in a unique way. This type of top-load washer locks the lid during the cycle because it spins the basket at a high rate of speed in the spin mode. A vertical modular top-load washer flashes the Lid Lock light instead of a code when the washer won’t start.

What are the symptoms of a failed front load washer?

A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining. If you or a service technician determine that the machine control board has failed, this repair guide shows how to replace it.

What does it mean when your washer won’t start?

The wash cycle won’t start if the direct-drive washer doesn’t fill or the water-level pressure switch doesn’t detect that the washer filled. This video shows how to troubleshoot a top-load, direct-drive washer that won’t fill.

Is the Duramax 08 DMAX a good car?

Those being the only 2 things but i’d buy one again in a heart beat! From what I’ve heard, the 08 Dmax is pretty damn good, aside from less fuel mileage than the LBZ, but that’s to be expected with the emissions that all of the big 3 have to meet. I just can’t bring myself to embrace the new body style.

What kind of car is a 2008 GMC Duramax?

Friend is looking to buy a 2008 GMC Duramax 2500 crew, 4×4 auto. Are there any problem areas that he should know about? Thank you for the input is here and there.

What to do if your Duramax won’t start?

If the fuse is o.k. if you have a test light or multi meter test the terminals the fuse plugs into,there should be two terminals in the fuse box.Test for power on one of these terminals while someone is trying to start the vehicle.If you have power then the start circuit is good and the fault is in the starter itself.

Can a 2006 Chevy C5500 start without a key?

I have a 2006 Chevy C5500 with the duramax. Its a bus and I am going to turn it into a dump truck….hopefully. My issue as i said is no crank no start from the key. I was able to get it started by turning the key on and crossing a screwdriver over the terminals on the starter but I am not able to start it with the key.

What’s the name of the truck that won’t start?

My 2008 duramax will not… My 2008 duramax will not start, won’t even turn over all the dash lights come on and the head lights come on, it’s really cold here but this truck normally starts with no problem, can you help please?? Submitted: 8 years ago.

How can I tell if my car starter is at fault?

You can test at the starter as well but it can be difficult to gain access to.The large wire on the starter should have power at all times and the smaller purple wire should have power on when trying to start the vehicle.With power here this indicates the starter is at fault causing this here.

What kind of Chevy truck won’t start?

In this video we encounter a condition where a 2002 Chevy Silverado ( Similar to GMC Sierra ) pickup has a symptom of the engine cranks over but won’t start…. In this video we encounter a condition where a 2002 Chevy Silverado ( Similar to GMC Sierra ) pickup has a symptom of the engine cranks over but won’t start….

Why does my truck not start in the morning?

Windows do not work. Lights to not work. Locks, overhead lights, etc etc. The truck is a 5000 lb. paper weight. So a this point I am scratching my head. I pop the hood and check the starter fuse and starter relay. Fuse looks OK.

Can a Duramax 6.6 start without a fuel pump?

My son has a 2011 duramax 6.6 that will not start on fuel but will start with a shot of either and runs like a top. He has replaced the fuel pump, … read more Vocational, Technical or Tra… Vocational, Technical or Tra… Vocational, Technical or Tra… I was low on fuel and drove to station to get more but never ran out.

Can a Silverado HD 6.6 turn over but no start?

Once it starts running it … read more ASE Certified Master Techn… Turn over but no start. 2007 silverado hd 6.6. Checked turn over but no start JA: Will the headlights turn on? Is the battery fully charged? Customer: yes JA: What is the model/year of your Chevy? … read more

Why does my 2007 Chevy Silverado not start?

– YouTube 2007 Chevy Silverado Will Not Start? Thought It Was A Battery Problem? If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

What kind of truck has a 6.6 Duramax?

I have a 2009 chevy 2500HD with the 6.6 Duramax. I started the truck with my remote while I was opening my shed it ran for a couple of seconds … read more 2017 Duramax will not idle and I kill it and restart it might run normal or I might have to keep killing and restarting till it runs. Once it starts running it … read more

Why does my 2015 Duramax high country not start?

I have a 2015 2500 High Country with 45k Miles. I was in line at a drive through and the lady asked me to turn off my engine cause she couldn’t understand my order. I did and when i tried to start it back just turns over but wont start. Pushed it to a parking place and notice diesel coming from the fuel filter where the water seperator screws in.

Why does my Duramax engine keep losing Prime?

Its usually getting the air out out of injector lines on mechanical injection systems after pump and or injector replacement. Don’t leave the key on and allow the grid heater/ glow plugs to get hot. Spray either, turn key and start immediately. Key is don’t be a an idiot and spray half a can.

What causes a Duramax injection pump to fail?

As a result (allegedly), the lack of lubrication in the fuel can cause a premature failure of the injection pump, to a point where it won’t allow the LML Duramax to run. You can be driving down the road and everything seems normal, and when the pump fails, the truck just shuts off.

What should I do if my Duramax engine wont start?

With the engine OFF, loosen fuel filter assembly plastic bleed screw a turn or so, and depress the round priming pump on top of FF assembly until fuel squires out of vent. CAREFULLY close plastic vent nut with fingers or nutdriver. Depress pump until firm. Barely finger tight with nutdriver is all you need.

Why does my 2005 LLY Duramax not start?