Why are my brake lights not working on my GMC Canyon?

Brake lights are not working. Hey Everyone! Enter your ride HERE to be a part of this months Ride of the Month Challenge! Over the weekend my brake lights have quit working. The reverse lights and turn signals work still? Would it be a fuse? Help please. If neither are working, check the fuse, and by check I mean I would just replace.

Is it dangerous to drive with brake lights not working?

Driving at night with either brake lights or tail lights not working is dangerous for you and other drivers on the road. It takes a long time to notice when the brake lights not working but tail lights are or vice versa. It is so because you won’t know what is happening in the backside while driving until someone points it out.

How to fix a 2005 Chevy Colorado door lock?

Click to expand… I also have a 2005 Chevy Colorado with the exact same problem. I followed the advice given, that is removing the negative battery cable and holding it against the positive terminal on the battery for 30 seconds to completely discharge the BCM (body control module) and waiting 6 hours then reconnecting the battery cable.

Why does my Colorado window lock not work?

The resistor and connector is an easy fix with the link ssgjurista gave you. I think the problem is the contacts between the two most times rather than the resistor itself.

Why is my brake light not working on my Silverado?

Sounds like the classic signs of a bad multi-function switch. Usually the middle brake light is tied directly to the brake switch so if that light works it indicates the brake switch is doing its’ job and power is good past the switch.

What should I do if my brake lights dont work?

My back up lights and running lights work. ive checked all my fuses replace the bulbs. ive replaced my brake light swicth and also my tail lamp circuit board. ive have not lost ground to my brake light sockets but not getting 12volts. See if the hazard flashers work.

Where is the brake light switch on my car?

Fuse Box and Light Switch. You have to find the fuse box or the power distribution center (PDC). You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm.

The resistor and connector is an easy fix with the link ssgjurista gave you. I think the problem is the contacts between the two most times rather than the resistor itself.

Why are rear lights not working but brake lights are?

If the rear light lights up correctly but does not become bright when the brake is applied then the switch of the brake is faulty. This circuit is connected with the brake pedal – if the switch is out of place or connected incorrectly then the pedal may not be able to complete the circuit correctly.

Are there any problems with my GMC Canyon?

I have a 2005 Canyon 4X4 crew cab with the 5 cylinder. It has been great. Now have 93K miles. No problems at all. It has never been back to a shop except for alignment and normal tire rotation and oil changes. Do my share of 4 wheeling too but no abuse, just back country driving and pulling a small camp trailer.

What to do if you have a brake light problem?

Owners with the brake light problem can get free repairs but must return to a dealership when the newly designed parts become available. The inspection and replacement part will both be free. Owners can contact Chevrolet at 1-800-630-2438, GMC at 1-866-996-9463, and Isuzu at 1-800-255-6727 or the NHTSA vehicle safety hotline at 888-327-4236.

Why are the brake lights not working but the tail lights are?

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.

Where are the brake lights on my car?

You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm. Any problem with the fuse box and light switch will affect the brake lights.

Why are the rear lights on my car not working?

The causes for dysfunctional rear lights are: 1 Burnt bulbs 2 Blown out fuse 3 Damaged wiring 4 Electrical issues

What to do when your brake lights are not working?

Insure that the switch is indexed to the plastic retainer. Push the switch in all the way and rotate the switch clockwise until it “clicks”. Failure to hold the brake pedal all the way aft when doing this can result in dragging brakes. You mean by rearward is to push down or pull towards your self?

Where is the control switch for the dashboard lights?

Most vehicles have a dashboard lights control switch that will dim the dashboard lights, as well as turn them off. Check the control switch, which should be located on the console near the steering column or part of the headlight switch. [ [Image:Fix Dashboard Lights That Won’t Light Step 1 Version 3.jpg|center]]

What to do if your dash light does not work?

#Test the dashboard light bulbs. If the fuses are working properly, check for a blown bulb in the dashboard. Following the manufacturer’s instructions, disconnect the battery while working on the dash, remove the faceplate covering your vehicle’s dashboard gauge panel. Remove the screws holding the plate on. Carefully remove the faceplate.

What kind of warning lights are on a GMC Yukon?

They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are over 40 of them, so search carefully! Models examined include Acadia, Savana, Sierra, Terrain, and Yukon.

Why are the lights on my dash not working?

Flip the switch or turn the dial or knob up and see if the lights on your dash come on or get brighter. If adjusting the switch doesn’t work, you may have a blown fuse or bad lightbulb. Or, the entire switch may be faulty, in which case, have it replaced by a certified mechanic.

Where are the lights on the dashboard located?

Most vehicles have a dashboard lights control switch that will dim the dashboard lights, as well as turn them off. Check the control switch, which should be located on the console near the steering column or part of the headlight switch. Tail lights and dash lights are connected through the tail light (and/or brake light) fuse.

How long does it take to remove brake light switch?

I had first checked the fuse but this was ok. The brake switch was removed from a peugeot 406 but this is the same type of switch fitted to many makes of cars. Initially the job looks impossible but as you will see it only takes less than a minute to remove the switch. Loading…

Can a brake light burn out at the same time?

Two brake lights burned out are likely to get some attention. The majority of drivers never check their lights until they get stopped by a cop. Very true. That would explain both going at the ‘same’ time.