Easy tips

Where are the fuse panels on a Chevy Blazer?

Table of Contents

Where are the fuse panels on a Chevy Blazer?

Here you will find fuse box diagrams of Chevrolet Blazer 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 and 2005, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

What are the Illuminations on a Chevy Blazer?

Cluster Illumination, Radio Illumination, Heater Lamp, Four-Wheel-Drive Illumination, Chime Module, Fog Lamp Illumination, Rear Wiper Switch, Rear Defog Switch Illumination, Liftglass Release Switch Illumination, Overhead Console Illumination

When was the second generation Chevy Blazer Made?

In this article, we consider the second-generation Chevrolet Blazer, produced from 1995 to 2005.

Here you will find fuse box diagrams of Chevrolet Blazer 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 and 2005, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

Cluster Illumination, Radio Illumination, Heater Lamp, Four-Wheel-Drive Illumination, Chime Module, Fog Lamp Illumination, Rear Wiper Switch, Rear Defog Switch Illumination, Liftglass Release Switch Illumination, Overhead Console Illumination

How can you tell if there is a fuse in your car?

The wiring circuits in the vehicle are protected from short circuits by fuses. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.

In this article, we consider the second-generation Chevrolet Blazer, produced from 1995 to 2005.

Where is the fuse block on a GMC Sierra?

The fuse block access door is on the driver’s side edge of the instrument panel. Pull off the cover to access the fuse block. Instrument Cluster, DRL Relay, Lamp Switch, Keyless Entry, Low Coolant Module, Illuminated Entry Module, DRAC (Diesel Engine)

Why are my turn signals blinking so fast?

1 Bad Shape of Ground Connection If the combination switches are dirty and need cleaning, this clearly indicates that the ground connections are in bad shape. 2 Faulty Bulb Even when you encounter a bulb failure in the headlamp then, also the turn signals start blinking fast. 3 Insufficient Voltage

How can I Change my Turn signal Flasher?

Change the Turn Signal Relay One of the easiest repairs ever, you can also do it on your own (if aware of the system). To start with it, find the relay cluster and the turn signal relay in your car. Next, replace the old signal flasher relay with the new one and the very next minute, your car is back to normal blinking.

What happens when a turn signal fuse fails?

Learn more – To locate the fuse consult the owner’s manual or search Google Images. Step 3 – When a turn signal flasher or relay fails the blinkers will not operate or come “ON”, but not blink. A direction signal system is designed to operate with a flasher or blinker unit which interrupts the signal which created the blinking action.

What to do when your turn signal is not working?

Step 2 – Locate the power distribution center (PDC) or fuse panel to check all system fuses. Learn more – To locate the fuse consult the owner’s manual or search Google Images. Step 3 – When a turn signal flasher or relay fails the blinkers will not operate or come “ON”, but not blink.

Why is my blinker not working on my Turn signal?

A direction signal system is designed to operate with a flasher or blinker unit which interrupts the signal which created the blinking action. Learn more – Locate turn signal flasher in Google Images. Step 4 – When a turn signal switch fails the system will short or go “open” causing the blinker not to operate.

Where is the blower relay on a fuse block?

Pull the blower relay out of the fuse block. The blower relay is located near the front of the fuse block and is labeled “Blower.” Inspect the center of the relay. If the metal rod inside is broken, the relay will need to be replaced.

Where is the fuse block on a Honda Accord?

The fuse block is located in the upper corner of the engine compartment, and the cover can be removed by hand. Pull the blower relay out of the fuse block. The blower relay is located near the front of the fuse block and is labeled “Blower.” Inspect the center of the relay. If the metal rod inside is broken, the relay will need to be replaced.

What happens when a flasher relay goes bad?

While they are a very simple component in both design and operation, flashers play an important role in the overall driveability of a vehicle, and can compromise safety when they fail. Usually a bad or failing flasher relay will produce a few symptoms that can alert the driver of a potential issue. 1. Turn signals or hazards do not function

Pull the blower relay out of the fuse block. The blower relay is located near the front of the fuse block and is labeled “Blower.” Inspect the center of the relay. If the metal rod inside is broken, the relay will need to be replaced.

When do you need to replace the blower motor relay?

If the blower motor does not function, car fuses are blown, or relays are melting, you may have to replace the car blower motor relay. 1. Blower motor does not function 2. Blown fuses 3. Melted relay The blower motor relay is the electrical switch that is used to supply the power for the vehicle’s blower motor.

The fuse block is located in the upper corner of the engine compartment, and the cover can be removed by hand. Pull the blower relay out of the fuse block. The blower relay is located near the front of the fuse block and is labeled “Blower.” Inspect the center of the relay. If the metal rod inside is broken, the relay will need to be replaced.

What are the safety features of the Chevy Blazer?

Blazer offers advanced safety technologies to help you detect potential hazards, helping give you the added confidence you deserve every time you get behind the wheel. Safety or driver assistance features are no substitute for the driver’s responsibility to operate the vehicle in a safe manner.

What kind of cargo area does Chevy Blazer have?

The perfect fit. Whether you’re traveling light or packing for a big trip, Blazer offers a spacious, flexible cargo area that can be reconfigured to fit your needs. Room for the big stuff. An available Adjustable Cargo Fence helps prevent items like luggage and groceries from shifting.

What kind of infotainment system does a Chevy Blazer have?

Chevrolet Infotainment System functionality varies by model. Full functionality requires compatible Bluetooth and smartphone, and USB connectivity for some devices. Map Coverage available in the United States, Puerto Rico and Canada. Read the vehicle Owner’s Manual for important feature limitations and information.

What kind of tailgate does a Chevy Blazer have?

Do these parts fit your vehicle? Find out now. 1969 – 1972 Chevy / GMC Blazer, Jimmy Lift Gate Hinge Covers – 4 Pc Set w/ Hdw. Only 1 left!

What kind of LS Mount do I need for a 1972 Chevy?

This kit shown is PN 4008, and allows the installation of LS power into your 1968 to 1972 GM A-body. UMI’s LS mount places the engine in the factory location, but it also gives you the ability to relocate the engine rearward up to ¾-inch, or forward ¼-inch.

Where are the fuel pump and AC relays located?

The AC relay is located in the same under-hood fuse/relay box the fuel pump relay is in (see illustration above). Locate the fuel pump and AC compressor relays in the under-hood fuse and relay box. Swap the relays .

How to troubleshoot a GM fuel pump relay?

The following tutorial may be of help: Troubleshooting The Fuel Pump (GM 4.3L, 5.0L, 5.7L) (at: troubleshootmyvehicle.com ). The following links will help you comparison shop for the fuel pump relay:

How to test a GM 4.3L fuel pump?

More GM 4.3L, 5.0L, and 5.7L Tutorials. It’s very important that you start off your fuel pump relay diagnostic by first testing the fuel pump pressure with a fuel pressure test gauge. If the fuel pump relay IS NOT activating the fuel pump, the fuel pressure test gauge will register 0 PSI when cranking the engine.

What kind of Fuse is in Oldsmobile Bravada?

Oldsmobile Bravada (1990-1994). The wiring circuits in the vehicle are protected from short circuits by fuses. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse.

Why does my GM 4.3L engine not start?

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

Why does my 1999 Chevy Blazer not start?

I have a,1999 blazer I put a new battery in. And now it the three or four times to start after I get it started in don’t have a problem starting it all day New fuel pump, pressure is good. New programed ecm, new delco spider. , still injectors are not emitting fuel. Starter fluid will fire the engine but won’t stay running.

What is the fuse box on a Chevy Blazer?

A/C Compressor Relay, Cluster Chime Module, DRL Relay Coil, Four-Wheel-Drive Indicator Lamp, DRL Module, Rear Defog Timer, Transfer Case Control Module Ignition, SIR Redundant Ignition \\ RKE Ignition, fuel Sender

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

What causes a Chevy Blazer to shut off while driving?

Sudendly looses power and shuts off while driving… Coolant or antifreeze Oil Fuel pump Fuel filter Battery Fuses For two week’s prior to incident when i shut off the truck i could hear a boiling like sound coming from the coolant resivoir.

What kind of wiring is in a 1983 Chevy Blazer?

WIRING INFORMATION: 1983 Chevy S-10 Blazer WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT RED Ignition Harness STARTER YELLOW OR PURPLE Ignition Harness IGNITION PINK Ignition Harness ACCESSORY ORANGE Ignition Harness POWER DOOR LOCK (5-wire reverse polarity) LT.

Where are the fuses on a Chevy S-10?

Chevrolet S-10 (1993 – 1994) – fuse box diagram Year of production: 1993, 1994 Instrument panel The fuse block is in the instrument panel on the driver’s side. Fuses/Circuit Breaker Name Circuit protected A PWR ACCY Power Door Locks B PWR WDO Power Window 1 STOP/HAZ S Stop Lamps, Hazard Lamps, Chime Module 2 HORN/DM Dome Lamp, …

What kind of wiring does a K5 Blazer use?

Wiring Diagram For 85 K5 Blazer Wiring Library 87 K5 Blazer Wont Start Page 2 Gm Square Body 1973 1987 Gm 88 K5 Blazer Wiring Diagram Automotive Wiring Schematic Electrical Symbols Electrical Diagram Electrical Wiring Engine 73 87 Chevy Truck Wiring Harness 1984 S10 Fuse Box Unlimited Wiring Diagram Blazer Motor Diagram Wiring

What to do when Your Fuse goes out on your car?

To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure to replace a bad fuse with a new one of the identical size and rating. Fuses of the same amperage can be temporarily borrowed from another fuse location if a fuse goes out.

When to replace a fuse on an Oldsmobile Bravada?

Oldsmobile Bravada (1990-1994). The wiring circuits in the vehicle are protected from short circuits by fuses. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.

Can a broken fuse be replaced with a new fuse?

Do not repair fuses and never replace a blown fuse with one that has a higher amp rating. This can cause damage to the electrical system and fire. Never replace a broken fuse with anything other than a new fuse.

Where is the fuse box on a GM Truck?

IMPORTANT: The fuse box illustration and fuse descriptions cover the vehicles in the ‘Applies To:’ box on the right column. The fuse box is located on the driver side of the dash. Rear Intermittent Wiper/Washer Switch. Master Window Switch. Fog Light Relay. Rear Defogger Switch. Right Front Door Lock Switch. Power Mirror Inline Fuse.

Where are the fuses on a 1993 GM 4.3L?

In the table below you’ll find the fuse location and description of the fuses of the fuse box on 1993 4.3L, 5.0L, 5.7L TBI equipped 4.3L, 5.0L, and 5.7L pickups. IMPORTANT: The fuse box illustration and fuse descriptions cover the vehicles in the ‘Applies To:’ box on the right column.

Is the Chevy Blazer a full size truck?

Now, however, an automotive artist has drawn up a full-size Blazer model that looks ready to tackle to the trail. Posted to Instagram by user @wb.artist20, the new full-size Chevrolet Blazer rendering is based on the Chevrolet Silverado pickup truck, specifically the off-road-oriented Trail Boss trim level.

What kind of wiring is in a 1985 Chevy Blazer?

WIRING INFORMATION: 1985 Chevy S-10 Blazer WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT RED Ignition Harness STARTER YELLOW OR PURPLE Ignition Harness IGNITION PINK Ignition Harness ACCESSORY ORANGE Ignition Harness POWER DOOR LOCK (5-wire reverse polarity) LT.

Where is the fuse box on a 1998 Chevy S-10?

Chevrolet S-10 (1998) – fuse box diagram. Year of production: 1997. The fuse block is in the instrument panel on the driver’s side.

Why are my brake lights not working on my 1997 Chevy?

Pull the plastic cap off the fuse chassis and you’ll see a square relay fuse switch and replace it for the brakes. It’s only $13 bucks and is the predominant issue with 1997 Chevy Trucks and the brakes not working especially if you reverse and blinker lights do work. Was this answer helpful? Its the taillight circuit board or a broken wire.

WIRING INFORMATION: 1985 Chevy S-10 Blazer WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT RED Ignition Harness STARTER YELLOW OR PURPLE Ignition Harness IGNITION PINK Ignition Harness ACCESSORY ORANGE Ignition Harness POWER DOOR LOCK (5-wire reverse polarity) LT.

What are the symptoms of a bad Flasher relay?

Another symptom of a faulty flasher relay is hazards or turn signal lights that stay on. If the flasher has any sort of internal short it may cause the hazards or signals to stay on when they are activated, instead of flashing.

What happens when a turn signal Flasher is not working?

1. Turn signals or hazards do not function 2. Turn signals or hazards stay on 3. Additional lights are not working The hazard and turn signal lights found on the vast majority of road going vehicles are controlled by a flasher, which is commonly referred to as a relay.

Is there a problem with the turn signal hazard relay?

While issues with the turn signal hazard relay will not normally affect the driveability of the vehicle, they can cause problems that can compromise vehicle visibility and safety. While flasher relays are not complicated components, they can sometimes be difficult to diagnose due to the highly complicated nature of electrical systems.

What happens when your turn signal Flasher stops working?

If your turn signals have stopped working, it’ll be doing one of these things: blinking rapidly, coming on without blinking, or nothing at all. The good news is that all of these symptoms point to two possible issues, a bad turn signal relay or a dead bulb. If the signal blinks really fast, you have a bulb out on that side.

Is there a way to bypass GM security system?

Scouts Troop 980 of Utah cheers as their ’92 Olds Toronado is coming back to life. Thanks to the NEWROCKIES Full Bypass Module! How to FULLY bypass VATS Passkey and Passlock Security Systems in GM Cars. Has the dreaded GM Security system just hit you?

What happens when you close the hood on a car?

So, here’s a new tip for those who hate the system. As it turns out, engine auto-stop-start does not operate if the car is started with the hood open. Moreover, the system remains off even after the hood is closed, effectively disabling the system from functioning until the next key cycle.

Why is my Chevy Blazer 98 not working?

Description: This Chevy Blazer 98 4×4 w New venture 233 transfer case had the 4×4 not working. The system can be viewed in 2 parts, the computer controlled parts, which actuate the transfer case and locks the front drive shaft in. And part 2, the mechanical, which involves vacuum actuated and controlled parts.

Why is the 4 wheel drive light blinking?

The 4-Lo engaged the low-range transfer case for rough and challenging off-road driving. Fast forward a few decades and, enter the Actuator. The actuator is a component found mostly on modern four wheel drives and is designed to electronically engage 4 wheel drive.

Oldsmobile Bravada (1990-1994). The wiring circuits in the vehicle are protected from short circuits by fuses. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse.

What is the fuse box diagram for a Chevy truck?

Chevy Truck Fuse Block Diagrams – Chuck’s Chevy Truck Pages Chevrolet truck fuse box diagrams. 1973 – 1979 fuse box diagram. !980 – 1987 fuse box diagram. Great resource if the lettering is worn off yours

Why is my abs light on on my Chevy Blazer?

There have also been reports of an illuminated anti-lock braking system (ABS) light due to ABS control unit failure. While some did not experience any drivability issues because of this, others report one of the brakes locking up, causing the vehicle to pull over to one side.

What kind of fuse box does a Chevy S-10 have?

Alternator Field, A/C Compressor Relay, Cluster Chime Module, DRL Relay Coil, Four-Wheel-Drive Indicator Lamp, DRL Module, Transfer Case Control Module Ignition, SIR Redundant Ignition, RKE Ignition Oxygen Sensor Heater, Exhaust Gas Recirculation, Cam Sensor, CANN.

When did the first Chevy Trailblazer come out?

In this article, we consider the first-generation Chevrolet TrailBlazer, produced from 2002 to 2009.

How to fix Chevy S10 / Blazer light problem?

Chevrolet S10 / Blazer light problem fix! How to fix headlights, tail lights or dash lights If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

What are the warning lights on a Chevrolet?

The following are warning lights and indicators found in vehicles built by Chevrolet. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are nearly 50 of them so search carefully!

What are the warning lights on my dashboard?

So, what is that light on your dashboard? What follows is easily the most complete list available of symbols and warnings that may appear in and on your car’s dashboard or instrument cluster. The following are warning lights and indicators found in vehicles built by Chevrolet. Click a link to learn more about each one.

Where is the underhood fuse / relay center located?

The underhood fuse/relay center is located in the rear of the engine compartment near the brake fluid reservoir. WARNING: Terminal and harness assignments for individual connectors will vary depending on vehicle equipment level, model, and market.

Where do I find the fuse box diagram?

However, sometimes the wire may look intact even in the blown fuse. Fuse box diagrams presented on our website will help you to identify the right type for a particular electrical device installed in your vehicle. Use our website search to find the fuse and relay schemes (layouts) designed for your vehicle and see the fuse block’s location.

When do you need to replace a fuse box?

Inspect a metal strip (fusible element). A damaged one means the fuse has blown. If so, you need to replace it. However, sometimes the wire may look intact even in the blown fuse. Fuse box diagrams presented on our website will help you to identify the right type for a particular electrical device installed in your vehicle.

The wiring circuits in the vehicle are protected from short circuits by fuses. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.

When did the Chevy Blazer come out in the US?

Every Manual available online – found by our community and shared for FREE. Enjoy! The Chevrolet Blazer was a mid size SUV from General Motors between 1983 and 20 0 5. It was based on Chevrolet S-10 and technically the twin of GMC Jimmy.

Where is the fuse box on a Chevy S-10?

The fuse box is located on the driver’s side of the instrument panel, behind the cover. Dome Lamps, Cargo Lamps, Visor Vanity Mirror, Cigarette Lighter, Inside Rearview Mirror Lamp, Overhead Console Lamps, Glove Box Lamp, Horns, Horn Relay, IP Courtesy Lamps, Power Outside Rearview Mirror, Liftglass Release Motor, Illuminated Entry Module

What are the symptoms of a bad turn signal Flasher?

1. Turn signals or hazards do not function. The most common symptom of a bad or failing turn signal / hazard flasher is hazards or turn signal lights that do not function. If the flasher breaks or has any internal issues it can cause the lights to malfunction, or not respond at all when the turn signal lever or hazard light button are pressed.

While they are a very simple component in both design and operation, flashers play an important role in the overall driveability of a vehicle, and can compromise safety when they fail. Usually a bad or failing flasher relay will produce a few symptoms that can alert the driver of a potential issue. 1. Turn signals or hazards do not function

How many sensors does a 1997 Chevy Blazer have?

Four-wheel, disc-brake model Blazers have four sensors. Rear-drum-brake models have only two. Apply the parking brake on the 1997 Chevy Blazer.

Is there a disc brake on a 1997 Blazer?

Rear-wheel disc-brake models of the 1997 Blazer have speed sensors connected to the rear wheels the same way they connect to the front wheels. Rear-drum models do not employ rear-wheel speed sensors on the rear ABS system. Apply the parking brake on the Blazer.

What is the variable speed sensor on a blazer?

The variable speed sensor is responsible for the speedometer reading in the Blazer. The other type of speed sensor on the Blazer is the antilock brake system (ABS) wheel speed sensors. These sensors read the individual wheel speeds to communicate with the ABS system.

What are the specifications of a 1997 Chevy Blazer?

Trans Description Cont. Again Electronic Manual lap/shoulder safety belts for outboard front seat… Child seat locking latch – all outboard passenger seating… Looking for other models of the Chevrolet Blazer?

The fuse box is located on the driver’s side of the instrument panel, behind the cover. Dome Lamps, Cargo Lamps, Visor Vanity Mirror, Cigarette Lighter, Inside Rearview Mirror Lamp, Overhead Console Lamps, Glove Box Lamp, Horns, Horn Relay, IP Courtesy Lamps, Power Outside Rearview Mirror, Liftglass Release Motor, Illuminated Entry Module

Are there any problems with the Chevy 4.3 Vortec engine?

The 4.3 Vortec engines made from 1996-2002 (L35 and LF6) have been reported to have engine knock problems. In a properly functioning engine, fuel burns in even pockets instead of all at once. The pockets burn in even timing, in sync with engine cycles. Engine knock occurs when the fuel burns unevenly and out of sync with the engine cycles.

WIRING INFORMATION: 1983 Chevy S-10 Blazer WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT RED Ignition Harness STARTER YELLOW OR PURPLE Ignition Harness IGNITION PINK Ignition Harness ACCESSORY ORANGE Ignition Harness POWER DOOR LOCK (5-wire reverse polarity) LT.

How do you replace the instrument cluster on a trailblazer?

Disconnect all three of the wires at the rear of the instrument cluster and pull the cluster out of the TrailBlazer. Install a replacement cluster and attach all three wires to the new cluster. Reinstall the four cluster screws and the dash trim. Reattach the three screws to the dash trim.

Why does my car not start when I put the key in?

Putting the key in the ignition switch and starting the car feels like second nature. However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems.

Can a unworn key turn an ignition cylinder?

Or, an unworn key may not turn a worn ignition cylinder, as they haven’t “worn together.” How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders.

How to reset an anti-theft radio on a Chevy?

Press the “AM/FM” button until “SEC” appears on the radio display. Press the “ON” button on the radio. The radio is now reset. Press the “Minute” and “Hour” buttons slowly until the security code matches. Going too fast may cause you to skip over the correct numbers of the security code. Store your radio security code in a safe place.

What kind of FM radio does a Blazers use?

Please note that Blazers use both mounts depending on the body. This is a truck slide mount. We also have this radio as a Car Mount. This radio is a remanufactured AM FM CD GM Code UNO as used in Chevrolet and GMC Trucks from 1995-2005. This radio is professionally rebuilt including all of the light bulbs in the face.

Is the factory radio in a 98 Cavalier?

This is the same radio as was in my 98 Cavalier, and it cost me $500 extra as an option when I bought the car, so I consider this stereo a real bargain. This refurrb’d unit hooked right up to the factory wiring harness, and it performs beautifully.

Press the “AM/FM” button until “SEC” appears on the radio display. Press the “ON” button on the radio. The radio is now reset. Press the “Minute” and “Hour” buttons slowly until the security code matches. Going too fast may cause you to skip over the correct numbers of the security code. Store your radio security code in a safe place.

When did the Bussmann brothers start making fuses?

With greater than 21 billion in revenue and customers in more 175 countries, we have the capability to make a difference and we do every day. It’s been more than 100 years since the Bussmann brothers first started producing fuses from the basement of their home.

Can a fuse be borrowed from another amperage?

Fuses of the same amperage can be temporarily borrowed from another fuse location if a fuse goes out. Replace the fuse as soon as possible. Before replacing a fuse check that the key has been removed from the ignition and that all the services are switched off and/or disengaged.

Why is my Fuse Box making a clicking noise?

This can be caused by a computer failure, resistance in the ground wire for the control side of the relay or high resistance in the power supply to the control side of the relay. To find out the source of the problem, you’ll need to run some quick tests using a multimeter.

What happens when the brake light switch fails?

It also sends a signal to the vehicle computer when the brakes are applied. In newer vehicles, this information is used for push-button start, anti-lock brakes, and vehicle stability control, but these features may not operate if the brake light switch has failed.

How to wire a headlight enhancement relay kit?

This video is a detailed walkthrough of the American Autowire headlight enhancement relay kit. Our kit includes separate relays for the high and low beams as well as upgraded GXL wire to make fresh connections to your lights. It’s available in both standard (pn/ 500403) and weatherproof (p/n 500431) form. Loading…

What causes hesitation and surging on Blazer 4.3L?

Fix Hesitation and surging on Blazer 4.3L If you have Hesitation and surging on Blazer 4.3L and it’s driving like a dog—poor acceleration, hesitation, or a surge and you suspect a fuel problem, you may be partially right.

Why is my Blazer 4.3L driving like a dog?

If you have Hesitation and surging on Blazer 4.3L and it’s driving like a dog—poor acceleration, hesitation, or a surge and you suspect a fuel problem, you may be partially right. But before you start replacing really expensive components like the fuel pump, try this: Disconnect the electrical connector to the MAF sensor and take it for a drive.

Author Image
Ruth Doyle