When using a forklift what does the term fall zone refer to?

When using a forklift what does the term fall zone refer to?

The forklift fall zone refers to the area that the pedestrian should leave between them and the lift truck. The fall zone helps make sure that the pedestrian does not get injured in the event that cargo was to fall from the lift truck.

When depositing a load forks should be lowered to the point that there is slack in the chains?

Check behind the truck, sound the horn, and slowly back away. When the forks are safely disengaged from the load, stop the truck and lower the forks 4 – 6 inches above the floor. Be careful when lowering a load to avoid over-lowering the carriage to the point where there is slack in the chains.

How can you decrease the likelihood of injuries while using forklifts?

How can forklift injuries be prevented?

1. Slowing down the forklift whenever turning a corner and maintaining the reduced speed throughout the turn.
2. Lowering the forks and tilting them back for better stability when carrying a load.
3. Never overloading the truck and removing unstable loads.

When you’re driving a forklift you should position the forks?

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.

What is the safe distance from any suspended load?

At a minimum, stay at least 10 feet radius from where a suspended load could fall if there was failure. If a load is suspended higher, increase the radius. Remember that a suspended load can be anything moved using such equipment as a crane, forklift, hoist or tractor bucket.

How would a worker driving a rough terrain forklift prevent it from tipping over?

There are many things that forklift operators can do to avoid tip-overs, including:

1. √ Drive slowly and safely.
2. √ Keep the load tilted backward.
3. √ Avoid sudden braking.
4. √ Avoid exceeding the lift’s maximum load capacity.

What are the 4 main causes of injuries when using forklifts quizlet?

The main causes of injuries when using forklifts are overturns, striking pedestrians, being crushed by a forklift, or falling from one.

How low should forks be driving forklift?

Travel with forks as low as possible from the floor and tilted back (usually within 10-15 cm (4 to 6 inches) above the floor). Match speed to, load, presence of pedestrians, obstructions, and driving and workplace conditions, including slippery surfaces.

Why are forklifts considered to be work equipment?

The law requires that workplaces are maintained in a condition that is safe and without risk to safety and health. Vehicles must be kept safe and fit for purpose and the driver must be able to get in and out of the vehicle safely. Forklifts also are classed as work equipment.

What should I wear to work on a forklift?

Employees have legal duties to use work equipment in a safe manner in line with procedures developed by their employer. Always: ✓Wear appropriate personal protective clothing as provided by employer. Hard hat, protective footwear and high visibility clothing are recommended as a minimum when working around forklifts.

What’s the proper way to Park a forklift?

Park the forklift in a safe place, on level ground; never on a slope Leave the forklift with the mast tilted forwards and the forks fully lowered, with the tips on the floor Apply the parking brake, select neutral, switch off the engine and remove the key Return keys or other activating devices to their place of safe-keeping

What should the fork position be on a forklift?

While different loads require unique angles, a slight tilt is all that is needed on most lift trucks to help retain loads when a fast stop is required. Unstable, round, liquid or loose stacked loads may require higher degrees of tilt back.

Can a person walk under a raised forklift?

Don’t let anyone walk under raised forks or load. If given a load to handle and someone is required to hold or position the load while the lift truck is moving –STOP. There is something wrong. If unable to handle the load alone, change the load or the equipment. Otherwise, someone will eventually be hurt badly. Don’t take this risk.

Can a forklift be used to elevate an employee?

Consequently, OSHA prohibits the use of such equipment to elevate personnel. If the owner’s manual for the equipment is silent on whether the equipment may be used to elevate personnel, the employer must determine if the forklift was designed for such purposes.

Can a fork be left on the ground?

Forks on the ground are a trip hazard. However, if the forks are on the ground, you get an opportunity to lift your foot as you trip to recover balance. If a fork tip or heel is left up, a pedestrian stepping over can hook her foot underneath and fall. This is referred to as a “hook fall”.