When does the Ford Explorer engine shut off?

The vehicle will just shut off at anytime. It’s not the auto start feature, all power will turn off at anytime. It has happened numerous times while driving waiting at a red light or to make a turn. It always happens while driving in the city. See all problems of the 2020 Ford Explorer .

What are the problems with a 2004 Ford Explorer?

See all problems of the 2004 Ford Explorer . The contact owns a 2016 Ford Explorer. While driving approximately 40 mph, the engine shut off. The contact turned off and restarted the vehicle, and the check engine indicator illuminated. The vehicle was taken to a local dealer where it was diagnosed that the throttle body needed to be replaced.

What causes a car to stop while driving?

The crankshaft sensor is a necessary part to make your car engine running on a lot of car models. On some car models, you do also have a camshaft position sensor, which the car uses if the camshaft sensor is faulty. In this case, a faulty crankshaft position sensor may not cause the car to stop entirely.

Can a faulty crankshaft sensor cause a car to stop?

The crankshaft sensor is necessary for your car engine to run on most car models. You also have a camshaft position sensor on some car models, which the car uses if the camshaft sensor is faulty. Here, a faulty crankshaft position sensor may not cause the car to stop entirely.

Why does my car shut off after I stop driving?

If you car shuts off after you stop it is because the engine is very sensetive at the idle. This can be caused by a lot of things but is usually caused by a lean fuel mixture, causing the idle to drop too low. A faulty throttle body can also cause this.

Why does my Ford 4.0L explorer not start?

So, when your Ford 4.0L Explorer (Aerostar, Ranger or Mountaineer) Cranks but Does Not Start, it’s because one of these components is missing from the mix.

What does the theft light flashing on a Ford Explorer do?

The THEFT light flashing is a passive system that shuts off the fuel pump (cranks but won’t start or starts and dies). Does your key have a chip in it? You might try another (chipped) key if it does. You may need to hook up scan tool to see what is going on with the theft deterrent system.

What kind of car shut off without warning?

Tl the contact owns a 2012 Ford Explorer. While the contact’s wife was driving 65 mph, the vehicle shut off completely without warning.

Can a Ford Explorer have a no start condition?

Testing a Cranks but Does Not Start condition on your 4.0L Ford Explorer (Aerostar, Ranger, Mountaineer) doesn’t have to be hard. In this tutorial, I’ll go into the basics of a no start condition and show you some of the step-by-step tutorials that’ll help you get to the bottom of the problem.

What makes a Ford 4.0L engine not start?

This tutorial is geared toward a Cranks but Does Not Start Condition. To successfully troubleshoot the cause of the no start condition of your Ford 4.0L equipped car or mini-van, you need to know that there are three very basic components the engine needs to start and they are: Air. Fuel.

What should I do if my car wont start?

When the security light goes off, turn the ignition off, wait 20 seconds, and then start the engine. These are the most popular ways to solve the problem of anti theft system car wont start.

Tl the contact owns a 2012 Ford Explorer. While the contact’s wife was driving 65 mph, the vehicle shut off completely without warning.

What causes a car to start but not keep running?

The engine requires the right amount of air and fuel to mix together for ignition. If there is a fuel leak somewhere, then the correct amount of fuel may not make it to the combustion chamber. This might be enough to allow the engine to start, but not keep running.

Why does my Car start then immediately shut off?

Compustar and Arctic Start systems monitor voltage or tachometer signals from your vehicle to know exactly when the vehicle has started. Use this field to document the answer to the question discussed in the Knowledge Article. The most common reason for a vehicle to start, then immediately shut off is engine checking.

Why does my Ford Explorer not lock the door?

The car will not be safe for parking, especially in public places, as the key fob cannot lock the doors. Door ajar malfunction is a common problem for Ford explorer users. Some of the issues: The door ajar sensor in the door hatch may get stock and malfunction. The door sensor may be faulty.

What to do if your Ford Explorer door is ajar?

There may be problems with the wires connecting the sensor to the car computer. Spray a WD-40 spray liberally on the door hatch. Open and close the door a couple of times to free the mechanism. If you discover a faulty sensor, you can contact your dealer for a replacement. Check for broken wire among the door wire and fix it.

How did Ford Expedition engine shut off without warning?

By time engine turned back on, acknowledged reverse, engaged reverse, responded to accelerator being pushed, gear engaged, the truck was about to hit me as driver did not see me. Luckily driver noticed and slammed on brakes. By this time, vehicle was still trying to move so if truck did not stop, I would have been hit.

What are the problems with a 2005 Ford Expedition?

See all problems of the 2005 Ford Expedition . Engine just shuts off, especially at a stand still & a/c on. Not as often if a/c is not on. Driving down state highway when the battery gauge went to “l” and the abs light came on. The engine was still running. Pulled into apartment complex parking lot and the engine shut off.

Why does my Ford Escape shut down while driving?

The problem started last year with the Engine Coolant Low light coming on, then graduated to the Engine Temp Dangerously Hot – Stop Safely as the car goes into limp mode. Numerous times it has been to the shop, sometimes towed, and sometimes driven.

How can I tell if my Ford Explorer is running?

ThAnkyou Tracy, , best u can tell fuel is pumping, air filters brand new and seems ok, spark plugs have fire, intrigued by the computer and anti-theft device, after the fact, post checking all the other basics, theft warning light stared to flash intermittently and was no longer able to lock/unlock doors thru the key alarm…

Is there a problem with my 2013 Ford Escape?

No one has added a helpful site for this 2013 Escape problem yet. Be the first! Read reviews of repair shops in your area. Enter your zip code: Like many others, this Escape stalls out at idle and when pulling out into traffic. We have had it into the shop 5 times for this problem and it still has not been fixed.

How many times has Ford Expedition engine shut down?

This relay has been replaced twice in our 2003 Ford Expedition. We were on the interstate when our vehicle shut down completely and had hard time maneuvering it. Vehicle would turn on and off.

Why does my Ford Expedition stall out while driving?

It now stall out 10 minutes on the DOT after starting… after idle or driving. That tells me its not mechanical and must be something electrical getting hot and shorting out or losing contact. Usually its starts back up and I floor it to wherever I have to go with no problems but past two weeks it wouldnt start back up and had it towed twice.

Why is my Ford Explorer key stuck in the ignition?

All vehicles equipped with automatic transmissions have a lock that keeps the key from being removed from the ignition while the vehicle is in gear. This prevents your Explorer from “rolling off”. When the vehicle is in any other gear than park will act like neutral and roll away without the parking brake on.

What happens when you turn off the ignition key?

When you switch off the ignition key, the ignition relay should also shut off power to all engine components; otherwise, it will drain the car battery when you let the car stands over the night. When the ignition relay fails, it can cause the ignition system to be activated constantly, even when you have removed the keys from the ignition.

Can You unbind a key from a Ford Explorer?

Manipulating your Explorer’s steering wheel can unbind the key. Bent – Over time and repeated use, a key can bend. If this is the case, you’ll need to get a new one. This issue often happens with cheap duplicated keys. If you do massage the key out, go ahead and throw it away.

Why is my ignition not working on my Ford Explorer?

Unseen cause triggers the event. The contact owns a 2010 Ford Explorer. While driving various speeds, the contact heard a rattling noise coming from the engine. In addition, the key failed to eject from the ignition switch. The vehicle was taken to the dealer (irvin motors in san antonio, TX), but was not diagnosed or repaired.

Why are the lights coming on in my Ford Explorer?

Test drove with a tech to show problem of ignition switch causing the interior lights to come on while car is being driven. While test driving and moving the ignition switch, the interior lights did come on. On the third example, the car cut off.

Why did my fuel gauge stop working on my explorer?

I hooked up a trailer that was wired incorrectly and it blew the trailer battery power fuse. At the same time, the fuel gauge seemed to st … read more Today, all the sudden, the fuel gauge, power windows and radio, all stopped working on my 2004 ford explorer. everything else seems to work fine.

How can I tell if my Ford Explorer has no power?

Ask Your Own Ford Question Ford Mechanic: Ron, ASE Certified Technician replied 10 years ago Check and see if you may have left one of you power wires off the positive battery side of the solenoid, all power to the car starts there. Ask Your Own Ford Question Customerreply replied 10 years ago

Where does the power come from in a Ford Explorer?

All your power comes from the battery cable side of this solenoid, the positive battery cable runs to the solenoid, and there should be 3 or 4 other small fuse linked wires also hooked to this side, this is the power wires going into the truck. The other side is the cable down to the starter.

What was the battery problem on my 1994 Ford Explorer?

Ron : The 1994 had known issues with a bad end on the positive battery with the connection on the smaller red wire coming out of the connection at the positive post on the battery. I would start with eaither reeplacing the cable end or the complete cable. JACUSTOMER-3ao1dpav- :

Why does my Ford Expedition shut off while driving?

Ford vehicle shuts off sporadically with multiple warning lights while driving and stationary. The brakes also seize up to the point where they over heat and could catch fire. The most recent event happened may 15th after picking the car up from my local repair shop to try and repair what Ford dealerships has not been able to repair.

What should you do if your car shuts off while driving?

When your car shuts off while driving on the road randomly, the first thing you should check is your car fuel tank. An empty fuel tank happens to most of us. Of course, you can not drive a car with no fuel. Thus, looking at the fuel gauge may definitely save you from standing on the roads for hours and hours.

Why is my reverse not working on my 4L60E?

Valve Body Issues- A bad valve body can make the reverse gear not work in the 4L60E. If the valve body ends up warped, or if the gasket fails, it’s entirely possible that the gear won’t engage. Booster Valve- A bad booster valve can leave you without reverse in a hurry. Sun Shell- A broken sun shell will cause the 4L60E to lose reverse.

https://www.youtube.com/watch?v=2wiN8MV278A

Where can I get a Ford Explorer that will not start?

The contact stated that after multiple attempts to start the vehicle, the engine would not crank, as the check engine light illuminated. The contact had the vehicle towed to jim click Ford Lincoln 6244 e 22nd st, tucson, az 85711 where the dealer was unable to diagnose the vehicle.

What are the problems with the 2013 Ford Explorer?

See all problems of the 2013 Ford Explorer . Tl- the contact owns a 2013 Ford Explorer. The contact stated that after multiple attempts to start the vehicle, the engine would not crank, as the check engine light illuminated.

What are common reasons my Ford Explorer won’t start?

What are common reasons my Ford Explorer won’t start? While there are a variety of reasons your Ford Explorer won’t start, the most common 3 are a dead battery, an alternator problem, or failed starter. How is a no-start diagnosis fixed?

Why is my Ford Expedition engine cutting off while driving?

Shortly after the engine would stutter and sometimes stall and would restart. Took back to our guy and we were having a devil of time repeating the experience. Eventually he finds a lose ignition wire and believes that was the fix.

Can a Ford Explorer shut off at any time?

Also please check out the statistics and reliability analysis of Ford Explorer based on all problems reported for the Explorer. The vehicle will just shut off at anytime. It’s not the auto start feature, all power will turn off at anytime. It has happened numerous times while driving waiting at a red light or to make a turn.

Are there any problems with the Ford Explorer?

Ford Explorer owners have reported 46 problems related to engine shut off without warning (under the engine and engine cooling category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Ford Explorer based on all problems reported for the Explorer.

How do I Turn Off anti theft light on my 2002 Ford Explorer?

Get into the Explorer and insert the known correct key into the ignition and turn it. If you use the wrong key, such as one that was cut to open the doors, the system will remain armed. If the car then starts, then you have disarmed the anti theft system.

What happens if you use the wrong key on a Ford Explorer?

If you use the wrong key, such as one that was cut to open the doors, the system will remain armed. If the car then starts, then you have disarmed the anti theft system. If not, move on to this: Ford Explorer keys have large black plastic, or molded rubber, heads.

This relay has been replaced twice in our 2003 Ford Expedition. We were on the interstate when our vehicle shut down completely and had hard time maneuvering it. Vehicle would turn on and off.

Why does my Ford Explorer shudder when driving?

Loss of power: while driving my 2015 Ford Explorer XLT with 3. 5l v-6 engine on the highway (10/04/18), the wrench light came on and the car started to shudder and lose speed. Pushing down on the accelerator had no affect and the car rapidly decelerated. The engine was running very rough with heavy vibration.

Is the 2001 Ford Explorer Sport for sale?

The 2001 Ford Explorer Sport has not been tested. Like what you see? Find the best deal on a Ford Explorer Sport today. There are for sale near you. Certified child passenger safety technicians conduct hands-on tests of a car’s Latch system and check the vehicle’s ability to accommodate different types of car seats.

Why does my Ford F350 shut down while driving?

If your Ford F350 is shutting down while driving, it’s a real safety hazard. Vehicles are a lot harder to control without power brakes or steering. Directly below is a list of the most common reasons why your F350 would randomly die while driving. It may help you in your diagnosis.

Why does my car shut off while driving?

The most common reason that a vehicle shuts off when driving is a lack of fuel. The most likely cause is an empty fuel tank aided by a fuel gauge that’s not as accurate as it looks. Even if it says there is fuel in there, bang on the tank. If it makes a hollow sound, it’s probably empty. 2. Fuel Pump or Filter

Where is the viscous coupling on a Ford Explorer?

Here’s a quick ditty about the viscous coupling: Ford first introduced the viscous coupling in the 1997 Ford Explorer and Mercury Mountaineer AWD vehicles. The viscous coupling is a completely sealed torque distribution device located inside the transfer case and is connected to the front and rear output shafts.

Why is the transfer case not shifting in my Ford 4×4?

These motors do malfunction on occasion and are the most common cause of the transfer case not shifting. The relay modules behind the dash also malfunction and will sometimes melt the harness connector at the yellow and orange wires that feed the shift motor.

Why does my Ford Explorer crank but not start?

Spark. So, when your Ford 4.0L Explorer (Aerostar, Ranger or Mountaineer) Cranks but Does Not Start, it’s because one of these components is missing from the mix.

How to disable the door ajar light on a Ford Explorer?

Why Is The Door Ajar Light Still On Even After All Doors Are Firmly Closed? 1 Spray a WD-40 lubricant liberally into the door latch. 2 Open and close the door firmly a couple of times to help work the grease in the mechanism. 3 Replace defective door switches 4 Fix structural causes, if any.

Why does my Ford Explorer not start when cold?

Engine Fails to Start When Cold If your engine seems to give you trouble only when cold, there are some specific components to look at. Using a voltmeter, check for battery power. Make sure fuel is reaching the injections and the fuel filter is not clogged.

What happens when the ignition switch is off?

Generally speaking, in the “OFF” position, the ignition switch doesn’t connect anything; in the “ACC” position, the radio or fan may be energized; in the “RUN” position, the engine control module is energized; and finally, in the “START” position, the starter relay is engaged. (These generalizations, depend significantly on year, make, and model.)

What happens if you have an incorrect ignition code?

The chip in the key transmits a specific code, of which there are millions. If this code matches the ones programmed into the vehicle, engine starting is enabled. An incorrect key code, such as from an unprogrammed key or damaged key, would prevent engine starting. Code “confusion,” such as having multiple keys can also occur, preventing ignition.

Why is my car not turning on when I Turn on the ignition?

Of course, if you access the car itself with your key, you likely won’t be able to turn on the ignition because of all those extra tumblers. And on the off chance that you do turn the ignition cylinder, the immobilizer won’t allow you to start the car, because it’s protected by one-in-millions of transponder codes.

What to do if your ignition cylinder is worn out?

How To Fix It: Fortunately, this is an easy fix. Just turn the wheel back and forth until the ignition cylinder is freed. It’s a fact of life that mechanical things tend to wear out, and the same goes for mechanical keys and key cylinders used in your car’s ignition system.

Why does my explorer lose power during acceleration?

My explorer seems to bog down during acceleration, mainly on days when it’s raining or when it’s hot outside. Had this problem last year and replaced the spark plugs and wires which seemed to solve the problem, however a year later it is happening again. Any suggestions on what it could be? helpful?

What should I do if my torque converter is not working?

Torque converter (automatic transmission only) may not be locking at the right time, or it may be slipping. The fix: Check lock up circuit or have the torque converter replaced. This is not a DIY job. There may be a vacuum leak. The fix: Check and replace vacuum lines as required.

When does a car lose power while driving?

Here’s one of the most expression you often encountered in car loses power while driving situation. You often encounter this situation when suddenly running at an unusually high speed. The soot in the combustion chamber fell into the mouth of the valve so it could not be closed, the machine died suddenly.

Where is the overide light on a Ford Explorer?

Put the key in the ignition, and turn forward all the way just before cranking. Then within 5 seconds, locate, press and hold in the valet/overide button, found under the dash area, (push button, spring loaded) until the installed LED (the blinking light) in your dash area goes on solid, and the siren chirps once.

What’s the problem with my 2002 Ford Explorer?

My 2002 ford explorer won’t start I changed my starterd and my battery and my alternater it still won’t start now my 2002 ford explorer won’t cut off when I turn the key ignition switch off what the problem please help me out 10 people found this helpful. Roll driver window down, get out lock door with key, remove key.

What are the symptoms of a Ford Explorer overheating?

Your Explorer will be equipped with a temperature warning light and/or a temperature gauge. The most common symptom of overheating is the temperature light coming on. If this light does come on, make sure that you get off the road quickly and safely. Driving while overheating can cause long term engine damage. 2. White Smoke

What to do if your Ford Explorer is stolen?

Take off the top cover of the steering wheel or theres a little square cover you can pop open with a screw driver. Put the screw driver in the opening and push down on this piece that is spring loaded and pull down on your shifter. Put your car back in Park and start your car! Hope this helps you guys! 10 people found this helpful.

How do you unlock 4WD in Ford Explorer?

171 people found this helpful. If that doesn’t work, try starting the truck put the transmission gear selector in neuteral. Then put the 4×4 switch/button into 4 low for a few seconds. Now put the 4×4 switch into 4 hi and then 2wd. Now put the transmission gear selector into drive or reverse move the truck 20-30 feet and it should be ok.

How does 4 wheel drive work on a Ford Explorer?

If that doesn’t work, try starting the truck put the transmission gear selector in neuteral. Then put the 4×4 switch/button into 4 low for a few seconds. Now put the 4×4 switch into 4 hi and then 2wd. Now put the transmission gear selector into drive or reverse move the truck 20-30 feet and it should be ok.

What causes your car to shut off while driving?

When the ignition switch is frazzled, this will lead to a loss or power to your engine due to vibration such as hitting a round patch of street. The loss of power causes the engine of your car to die suddenly while you are driving on the road. Check out this video to see more details:

What causes Ford Explorer engine to stall while driving?

This happened multiple times until our mechanic finally found what caused the plug to the computer to melt. See below: Sick to death of all the problems. Ford just throws these things off the assembly line and then says “Oh, so sorry, it’s out of warranty”. We actually won a lawsuit regarding a 2002 Explorer.

How to disable Auto Start / Stop feature in Ford Explorer?

Ford Explorer DISABLE Auto Start/Stop Feature – Toggle ON and OFF permanently! – YouTube

Why does my car run when the ignition is turned off?

With the ignition turned off and the car continuing to run, simply remove the plug from the alternator (DO NOT TRY AND REMOVE THE BATTERY POWER WIRE FROM THE POWER STUD!) and the car should shut off if the alternator is creating the problem. If it does not stop running, your feedback problem is coming from something other that the alternator.

What happens when I take my foot off the accelerator?

The engine dies when I take my foot off of the accelerator. Hello. If the engine runs fine when you are holding the accelerator pedal down and dies when you release it then you may have a couple of possible issues. I would first check the vacuum hoses going to the engine.

Why does my engine die when I take my foot off the gas?

This caused your engine to raise high up and make the engine fully extend the engine mounts. When… This can be caused by a number of things such as low coolant levels, a faulty thermostat, or a failing coolant fan switch. As you may know the coolant fan switch helps to maintain the proper coolant temperature by turning…

Can a Ford Explorer stall at any time?

Stalls can happen at any time, and it can be incredibly jarring when it does happen. Before troubleshooting any automotive issue, including stalling issues with the Explorer, make sure that you check the vehicles trouble codes with an OBD2 scanner.

Can a low oil level cause a car to shut off?

Can low oil cause a car to shut off? Low engine oil level does usually not cause your car to shut off. However, if it is too low so your oil pressure is getting low – the car can shut off the engine for safety reasons. This is often in newer cars, though.

What makes your car turn off while driving?

If there is something clogging in the pump or filter, it will make your car turns off while driving on the roads suddenly. So, it is always mandatory to check and clean the fuel pump, filter before driving a long distance.

What’s the problem with my Ford Explorer 1995?

Explorer 1995 – 1996, A by-pass kit should be fitted. The kit consists of a distribution element, reducer element and modified coolant hose. Problem: Overdrive (O/D) warning lamp flashes with or without diagnostic trouble codes (DTCs) P0741 and P1740, or both, in memory.

When does Ford Explorer hesitate during acceleration inspection?

Ford Explorer Engine hesitates during acceleration Inspection at your home or office. Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM. Our certified mobile mechanics can come to you now. Ford Explorer Engine hesitates during acceleration Inspection costs $89 on average.

Why does my Ford Explorer not accelerate when the RPM goes up?

Here are the most common cause of acceleration with the RPM’s going up: 1. Transmission Fluid Low If your Explorer is too low on transmission fluid, it’ll will no longer be able to transfer power to the rear wheels. The power goes to the torque converter, and that’s the end of the line. You should check the transmission fluid immediately.

What happens when you turn on cruise control on a Ford truck?

one more thing that occurs while you are driving on some fords is that the cruise control is defective and when turned on the truck will immediately shut off. The fix to this can be very very expensive, however, a quick fix is to turn the overdrive off in order to operate the cruise control and the truck will not shut off.

How big is a Ford 4.0 SOHC engine diagram?

Description : Parts® | Ford Piston Rings, Ranger, Part Of Piston. – 4.0L throughout Ford 4.0 Sohc Engine Diagram, image size 600 X 820 px, and to view image details please click the image. Here is a picture gallery about ford 4.0 sohc engine diagram complete with the description of the image, please find the image you need.

What causes the Check Engine light to turn off?

The error codes should be deleted which will cause the engine light to turn off. (Note: this method may not word on all car computers). In case, the car battery is disconnected and the light comes right back on, this may show an active problem and should be addressed and fixed.

What’s the best way to reset a check engine light?

In such a case, it is highly recommended to check the codes with a scanner instead. Switching the ignition on and off is also one method of hard reset without disconnecting batteries. Put the keys in your ignition and turn your ignition on and off consecutively after a second in each step.

How to disable the Check Engine light permanently?

Turn the automobile on and off thrice. To disable the check engine light permanently in some automobile, they will robotically reset the problem codes that triggered the earliest fault after the car is put on and off thrice in progression. You have to turn on your ignition.

Why are the interior lights not turned off in my Ford Explorer?

It use to be the little button down by your foot on older model vehicles which would be depressed when the door is closed. The switch is down (inside the door) by the lock mechanism. Sometimes it sticks and results in the interior lights not being turned off when you close the door.

What should I do if my Ford Explorer does not shut off?

There should be a plastic spacer (usually gray) around the post. If it is missing that is the cause of your problem. Check the other door strikers and compare them. On earlier model explorers the plastic insert can only be purchased for the tailgate, the entire striker needs to be replaced on the doors.

Why does my check engine light keep coming on?

A code reader can help you by manually allowing you to clear the fault code that has caused the check engine light to illuminate (in case it was stuck on due to an error in the car’s computer), or if there truly is something mechanically wrong then it can give you the “error code” that your car is producing.

What to do if your Ford Explorer is stalling?

Before troubleshooting any automotive issue, including stalling issues with the Explorer, make sure that you check the vehicles trouble codes with an OBD2 scanner. Trouble codes are always a great place to start diagnosing problems on today’s modern computer controlled vehicles. Without them, you are in the dark. These codes are vital to diagnosis.

Where is the gas cap on a Ford Explorer?

The gas cap was located behind the license plate and on every single Grenada, the spring on the license plate broke so they all drove around with their license plate facing the ground, wide open. We have no idea why the Check Engine light stays on. No idea why the back passenger windows quit working years ago.

When did Ford Explorer XLT have an oil leak?

2002 Ford Explorer XLT – WEIRD EXPENSIVE REPAIRS! Purchased used in 2004. Clear CarFax, 1-owner, under 50,000 miles. 2 mths later Oil Leak, output seal leaking, replaced seal.

What should I do about my 2002 Ford Explorer?

In ’06, replace leaking axle seals, May ’07 loose front driver’s side wheel bearings, rear noise inspected on lift, differential removed to find cause, replaced both front wheel bearings; noise STILL there.

Can a Ford Explorer have a failed transmission?

Because ford put a sealed transmission with this SUV, there is no way for regular person to check the ATF fluid level. With all these done, you won’t have a failed transmission. Recently I drove this car from Austin Texas all the way to Buffalo NY, and back to Austin, never failed.

Is the Ford Explorer good for gas mileage?

Decent gas mileage for an older SUV, keep it serviced at the Ford dealership and have had to put the usual front hubs and upper contol arms on it, which they are known for but aside from that, just routine maintenance. Great looking, relaible and reasonable cost to own! Was this review helpful? (14) (0)

What to do if your Ford Explorer starts stalling?

Thats out of the 180,000 Explorers sold during 2006. Mark. Yep, a bummer if you are one of the 4. A technique I have used before that worked is this; Take it to your friendly Ford dealer. Ask for the Service Manager. Tell him your problem, and leave him the car.

What causes a car to have no start?

The engine pistons and cylinder head valves (and all the other related components like: timing chains, etc.) are the ones responsible for the induction of the fresh air the engine needs for the combustion process. Although rare, internal engine mechanical problems can and do cause No Start Conditions.

Why does my Ford Explorer engine not start?

This is caused by engine heat transferring to the fuel and creating bubbles. You will notice the engine stalls, lacks power or it is hard to start or does not start at all. Inspect the feed and return lines and see if any are touching a hot engine part. Sometimes, the starter motor will operate but the engine will not turn.

What to do if your Ford Explorer starts Hot?

Then troubleshoot the engine coolant temperature sensor and engine control system. If the starting system only gives you trouble when the engine is hot. check the fuel filter and make sure the fuel injection system is receiving fuel. In rare cases, the fuel system may be experiencing vapor lock.

Why does my Ford 4.0L not turn over?

No Crank Condition The engine does not turn over when you turn the key to start your Ford vehicle. This is usually due to: Failed starter motor. Failed neutral safety switch. Failed ignition switch. Locked up engine.

What to do when your car won’t start?

When attempting to start the engine, make sure the transmission is in Park (P) or Neutral (N). Also, check the starting circuit for broken, loose or disconnected wires and cables from the battery to the starter solenoid, the ignition switch and the starter motor.

What does it mean when your Ford Explorer won’t start?

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your Explorer won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

Why does my Acura TLX engine not start?

When there is no spark, the engine will not start. You’ll probably have a misfire related code such as P0300, P0301, etc….. Ignition issues can be caused by many things, including bad spark plugs, bad coil packs, bad plug wires, computer issues, and more. 3. Engine Timing

What should I do if my Ford Explorer heater is not working?

Ford’s answer is the replace the entire heater box. That’ll mean removing the dash, discharging the A/C and replacing the entire module. Figure about $1,500 for that. Or, you can buy a blend door replacement kit from Dorman. The dorman part is 902-202. It fits the following applications:

What kind of air conditioning does Ford Explorer have?

2001 Ford Explorer Manual Air Conditioning; w/Floor Console Blower 2001 Mercury Mountaineer Manual Air Conditioning; w/Floor Console Blower 2000 Mercury Mountaineer Manual Air Conditioning; w/Floor Console Blower 1999 Mercury Mountaineer Manual Air Conditioning; w/Floor Console Blower

How to reset the fuel switch on a Ford?

FORD FUEL RESET SWITCH LOCATION. FORD DOES NOT START FIX. HOW TO RESET FUEL SWITCH – YouTube If playback doesn’t begin shortly, try restarting your device.

Can a bad ignition switch cause a car to not start?

by Jonathan Lister. The ignition switch in Ford vehicles is responsible for handling the electrical signals related to starting the vehicle. A failing ignition switch can cause system-wide problems ranging from the ability of the car to start, to maintaining speed and even keeping the radio turned on.

How to fix Internet Explorer shut down unexpectedly error?

Run Internet Explorer performance troubleshooter to fix IE shut down unexpectedly error 1. Press Windows key and click Search > Type: troubleshooting and select the topmost search result. 2. Click View all > Select Internet Explorer Performance > Advanced > Apply repairs automatically. 3.

What should I do if my computer won’t restart?

1) Go to “Power and Sleep” settings. Tell the computer to Never sleep. 2) Disable “Fast start”. 3) Shut down computer and reboot. 4) Do a restart from Windows.

What to do when Internet Explorer shuts down?

1. Run Internet Explorer > Click Manage Add-ons on Tool menu. 2. Click the name of add-on and click Disable to disable all add-ons > Close the Internet Explorer. 3. Restart IE browser to see if the problem has been fixed or not. 4. Click Manage Add-ons in Internet Explorer tool menu > Click and disable one add-on at a time.

What causes the engine to cut off while driving?

After doing some investigation he lands on the BCM or what Ford calls the GEM, after testing it he says it is okay but then finds his way to the ECM, electronic control module. He removed it had it tested and the read was it was shorting out causing the engine stutter and engine cutting off.

What causes a Ford fuel pump to shut off?

If your Ford ever fails to start or stalls on you suddenly, the first thing to check is the inertia fuel shut-off switch. The switch is designed to trip and cut power to the fuel pump in the event of a collision, but you can also trigger it by hitting a large bump or pothole as well.

Where is the shut off switch on a Ford truck?

If you own one of Ford’s pickup, SUV or van models, you can find the shut-off switch under the dashboard on the passenger or driver side, depending on what year it was built. If you own one of Ford’s car models, you may find it located in the trunk compartment.

Why does my Ford Explorer make a chugging sound?

My extremely used Explorer was driven off the lot, and ran like a champ for 3 months. One morning, I started it up, and noticed a chugging sound. While backing it out of the driveway, the truck felt like it was going to rattle apart.

How long does it take to stop at 60 mph?

You may want to use our Vehicle Stopping Distance Calculatorto do actual model calculations. 60 MPH = 88 fps. (fps=1.467 * MPH). If the vehicle deceleration rate is 20 fpsps (rather than the previously calculated 15 fps), then stopping time = 88/20 = 4.4 seconds.

Can a Ford engine be cut off completely?

Ford’s Auto Start Stop Engine Feature | Can it be cut off completely? – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

Why does my Ford Explorer engine cut out while driving?

Others had commented that the engine at low speed cruise would kick into overdrive at low speed and just wind up going too slow to keep running. With the overdrive off I monitored the tach and saw that it would come down to around 800 rpm or lower when going downhill so it makes some sense that with overdrive on it might kill the engine.

When does the a / C stop working in a Ford?

Ford E-Series Questions – A/C quits working when engine is under load. – CarGurus A/C quits working when engine is under load. When accelerating, my A/C stops blowing and only sometimes resumes blowing when a fairly low speed is attained. At highway speeds, it practically never runs.

Why does my AC quit working on my Ford E-450?

Normal operation. When the load or the throttle position reaches a predetermined point the AC compressor will automatically shut off until the load or the throttle backs off then it will kick back in. 5 people found this helpful. So, I’ve also had this problem in an E-450 can on my class C motor home. Took it to Ford.

Why does my car not start when I crank the engine?

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

Why does my Ford F150 not start up?

STARTING PROBLEM I have a 2000 ford f150 5.4L the truck cranks but will not start some times. if i spray starter fliud into the booster in will start up. but other times the truck will start then just idle off. There is good fuel psi, just changed the fuel pump relay. the problem stop for a while then started again.

What to look for when your engine won’t start?

Check for a blown fuse that may be preventing a circuit from working properly, like the fuel injection or computer system. To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition).

What’s the difference between no crank and no start?

There’s a big difference between a No Crank and a No Start Condition. Here’s a brief description of both conditions: No Start Condition: The engine cranks (turns over) like it wants to start but it never does. The usual culprits are: Failed crank position sensor.

What causes a car to crank but not start?

One of the biggest issues that causes a vehicle to crank but not start is ignition issues. When there is no spark, the engine will not start. You’ll probably have a misfire related code such as P0300, P0301, etc….. Ignition issues can be caused by many things, including bad spark plugs, bad coil packs, bad plug wires, computer issues, and more.

Is it unsafe to drive a Ford Explorer?

It is unsafe to drive though because the brake pedal could fail and you would have no brakes all if you still have the problem. The complete job cost me 1400 dollars and I am very unhappy about that.

When was the last time my Ford Explorer had a brake problem?

Very same problem on 2010 Explorer Eddie Bauer. Last time it happened several times in stop and go traffic in December 2017. Had it in the garage several times prior to this Recurring incident. It is in the garage now.

Why does my 2004 Ford Explorer stop running?

I read about this on the forum because my 2004 ford explorer was shutting off on me. after replacing the fuel pump, and Tune-up it when I decided to do some research. Many people have this problem and not even the ford dealers know how to fix it. People spend thousands of dollars due to this issue.

It is unsafe to drive though because the brake pedal could fail and you would have no brakes all if you still have the problem. The complete job cost me 1400 dollars and I am very unhappy about that.

Are there any brake problems with Ford Explorer XLT?

I have a 2005 explorer XLT. I have had the same problems. Driving slow push on brakes and they seize up and loud noise sounds like coming from ABS. Dealer to me the same thing, can’t find anything wrong.

Are there any problems with the 2002 Ford Explorer?

What causes a Ford Explorer to stall out?

If you don’t own/want to buy a scanner, most local parts stores will run a scan for you at no cost (they want to sell you the parts). Here are some of the issues that cause the Explorer to stall out. Remember, a vehicle needs air, fuel, and spark to run.

What does the fuel pressure regulator do when the engine is shut off?

Slow or No Start Part of the fuel pressure regulator’s job is to maintain fuel pressure at the fuel injectors at all times, including when the engine is shut off. Under acceleration, the vehicle should accelerate smoothly no matter how hard or light the gas pedal is depressed.

Why does Ford Explorer make noise when driving?

As a ford tech I have replace both rear and front wheel bearings on 02 and up explorers for that noise. mostly rears though. hope this helps. As a ford tech I have replace both rear and front wheel bearings on 02 and up explorers for that noise. mostly rears though. hope this helps.

What should I do about the front hubs on my explorer?

Front hubs aren’t so bad to do, but the rear ones require removal of the knuckle and hub assembly, and a press to put the new hub on the old knuckle. You can find instructions on Ebay on some listings for the bearings.

Why is idle speed not coming back up?

If the ISC system is working correctly, the PCM should adjust idle speed to keep the engine from lugging down when the A/C compressor engages. If idle speed drops down and does not come back up, the ISC system is not responding the way it should.

What to do when engine stall Idle Stop?

Aim for the little air bypass holes in the throttle opening. Use the small plastic tube that attaches to the nozzle on the aerosol can to aim the cleaner directly into the bypass port (s). Let the cleaner soak for at least 10 minutes before giving it another blast of cleaner.

How does the idle speed of an engine work?

The engine’s idle speed is controlled by how much air is allowed to bypass the throttle via the idle bypass circuit in the throttle body. The PCM monitors idle speed and operates a solenoid or small electric motor to move a valve that regulates airflow through the air bypass circuit.

What causes an engine to stall at idle?

If the ISC valve is gummed up with fuel varnish or dirt, it may stick, preventing the engine from maintaining the proper idle speed when the throttle closes. A faulty idle speed control circuit may also allow the engine to stall when idling if it fails to compensate for idle loads placed on the engine by the charging system or A/C compressor.

When did the transmission on my Ford Explorer start slipping?

Love this truck but forking out this kind of money for a new transmission is crazy this soon. Bought a 2007 Ford Explorer with 43,000 miles 2 years ago. In March with 71,250 miles the transmission began to slip. Now it’s to the point that I will need to repair.

When do I slow down and stop the car, engine shut off?

Ford Escape When I slow down and stop the car, engine shuts off Inspection at your home or office. Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

How does auto start stop affect engine life?

For most people, auto start-stop will have no effect on engine life. For some, it may actually extend it. If you spend hours idling in congested streets, you’re likely damaging your engine.

Is the door panel on a 2015 Ford Explorer coming loose?

With a car that is a 2015 Limited, the door panel should not pull loose. It is only 2 years old. I have had Fords my entire life and have had several Explorers. I have never had this problem. Apparently there is a quality control problem at the plant and they need to do a recall and have this fixed.

Help? Loading Curious how the 2015 Explorer compares to other years? Check out our Ford Explorer overview to see the most problematic years, worst problems and most recently reported complaints with the Explorer.

Is the steering wheel on a 2015 Ford Explorer?

THIS IS NOT SOMETHING THAT SHOULD HAVE TO BE REPAIRED ON A 2015 VEHICLE WITH LOW MILEAGE. TL* THE CONTACT OWNS A 2015 FORD EXPLORER. WHILE DRIVING AND ATTEMPTING TO TURN, THE STEERING WHEEL SEIZED AND THEN RETURNED TO ITS NORMAL POSITION.

See all problems of the 2013 Ford Explorer . The intermediate shift bracket sheared off/broke at the transition where it mounts to engine. Vehicle shakes violently while braking at higher speeds. . . Lesser movement at slower speeds while braking.

What to do if your crankshaft sensor is not working?

Issues with the crankshaft sensor can quickly lead to problems that affect the drivability of the vehicle. For this reason, if you suspect your crankshaft position sensor has an issue, have the vehicle inspected by a professional technician right away. They will be able to diagnose your car and replace your crankshaft position sensor if necessary.

Are there any problems with the Ford Explorer XLT?

2020 Ford Explorer XLT purchased new from dealer 04/2020. On two separate occasions the starter would not activate to start the car. When the brake is depressed the starter button and exterior lights flash. The car was towed to the Ford dealer, but the car started immediately according to technician. No issues were found.

Why did my 2020 Ford Explorer catch fire?

The contact owns a 2020 Ford Explorer. The contact stated that while at a drive thru window, the vehicle caught on fire under the hood.

Why does my riding mower run for 30-45 minutes then stops?

I have a Craftsman 18.o HP electric start lawn tractor model number 917.273752. A few days ago I began having a problem. The mower will run for 30-45 minutes and stop. After waiting 10 minute or so I can restart it and the whole process is repeated.

Why does my Ford Explorer engine Rattle all the time?

The number one rattling culprit in your Explorer’s exhaust system is the heat shield. They can get a little loose as the vehicle ages and accumulates mileage. Once this happens, it’ll rattle all of the time. It’s particularly noticeable when you rev the engine in neutral and let off of the gas pedal.

What is the emissions code on a Ford Explorer?

When the catalytic converter does fail, it’ll often give you code P0420, or P0430. If your check engine light is on, you may want to see if you have an emissions related code.

Adding insult to injury, the 2002-2005 Explorer also has a massive problem with the rear panel cracking. While it’s a minor annoyance compared to transmission failure, ironically the crack usually goes right through the Ford logo. Click on a category below for details. Help? Loading Curious how the 2002 Explorer compares to other years?

Why does my Ford Explorer stall at red lights?

18 people found this helpful. just tried the fuel relay. instead of spending approximately $20 in a new one, I switched the A/c relay with the Fuel relay to test it. so far, my truck is not stalling when I stop at a red light. since my truck is only shutting off on me once a week, I am going to keep it like this for about three weeks.

When did Ford Edge lose power while driving?

I they can’t find the problem. just on Sunday Aug 01, 2013 loss of power backing out of family member driveway no power to back out had to shut the car off and reset to get power to back out of small incline driveway. This is BS big time to sell the general public a vehicle that has problems that put your life in danger out on our roadways !

Why is the air conditioner not working on my Ford Explorer?

Like the radiator, the air conditioning condenser on Ford Explorer sits at the front of the vehicle and is responsible for releasing the heat from the refrigerant into the ambient air. Over time, grime, bugs and other small particles can build up on its surface and in the gaps of its mesh.

Why is the pollen filter on my Ford Explorer not working?

The pollen filter, also known as the cabin filter or microfilter, is a central component of the ventilation system in your Ford Explorer. A dirty filter causes the overall ventilation of the interior to deteriorate resulting in reduced cooling, heating and air flow.

Why is my Ford Explorer stalling at stoplights?

These were just some of the most common ones. A dirty throttle body can lead to stalling in your Explorer. If you let off of the gas coming to a stoplight and it stalls for a second or two and recovers itself, it very well could be a dirty throttle body that is causing the problem.

Ford Explorer DISABLE Auto Start/Stop Feature – Toggle ON and OFF permanently! – YouTube

Why does my Ford F 250 stop running?

A little over 50,000 miles. The truck would stop running while driving down the street, not start after driving, stop shut off and then would not start. Some times it may not start for several days then all of a sudden it would start up again and be fine for weeks then would start the whole process over again.

How often does a Ford F250 shut off?

The contact owns a 2003 Ford f250 super duty. While driving 70 mph, the vehicle shut off. The contact lost control of the power steering and brakes. The failure occurs at least forty times per week. The contact stated that he must turn off the vehicle and give it time to restart.

What causes a Ford Explorer to stop running?

And this other source talked about this because it can also cause the engine to shut off..

Where is the throttle position sensor on a Ford Explorer?

Your Ford Explorer uses a series of complex sensors to report what is going on to the ECU. The ECU then uses this information to adjust the timing, air fuel mixture, and more. When one of them goes wrong, it can lead to stalling for sure. Throttle Position Sensor – The throttle position sensor is typically located on the gas pedal.

Why did my car stop moving in the middle of the road?

About 10-15 minutes later while driving the car, it just slows down as if I took my foot off the gas, but I had not. The car was still running but had stopped moving. Luckily I was back home and was able to coast into a parking spot. Not sure what caused this because there were no warning signs of a failing transmission at all.

What happens when your car stops moving but is still running?

Q: In the middle of driving my car stops moving but is still running. I was at a traffic stop and when the light turned green I put my foot on the gas but the car would not move it just revved up. I got the car towed home, because it wouldn’t go into gear.

What causes a Ford F150 to shut down while driving?

The engine needs a strong ground to the chassis in order for your F150’s various electrical systems to work. If that cable is corroded, there could be problems such as misfiring, slow/no starts, or even the engine dying while driving. This is a common cause of many “gremlins”. 5. Bad Alternator

Which is the worst model of Ford Explorer?

However, the 2006 Explorer is the worst-rated model due to the high repair cost and extra problems at lower mileage. The Ford Explorer has numerous problems in different categories that are a part of your vehicle.

How can I tell if my Ford Explorer transmission is failing?

The transmission failure in your Ford can be noticed by the car jumping gears without warning, slipping in and out of gears while you’re driving, or preventing you from going into any gear. These are all signs that your transmission has failed, or is currently failing.

What’s the average rpm of a Ford Explorer?

I have a 2003 Ford Explorer that hasn’t been idling well lately. It normally idles around 800 or 900 rpms, but lately it will slow down to 400 or 500, then burst up to 1100 and repeat the process again. It doesn’t do this all the time, maybe only half-time.

Is there a way to reset the Ford fuel shut off?

To reset your Ford’s inertia switch, press down on the reset button. Although the location of the shut-off switch varies by year and model, Ford has stuck with a few common spots over the years.

How to tell if your air flow sensor is bad?

Therefore the most common signs of a bad mass air flow sensor usually appear in the form of an engine that is performing badly. Here are some of the most common bad mass air flow symptoms that you will typically come across. 1. Check Engine Light appearing on the dashboard

What happens if the mass air flow sensor is not working?

The job of the mass air flow sensor is to keep track of the amount of air coming in through the air filter, so that the ECU can adjust the amount of fuel getting into the engine. If the mass air flow sensor isn’t working properly then you will be faced with one or more symptoms such as lack of power and bad fuel economy.

Where does the vacuum go in a Ford E series?

There’s a black plastic vacuum tube from the intake that runs along the top of the engine on the right side. There is a Check Valve a Tee, and a vacuum reservoir. One end of the tee goes to the reservoir and the other through a grommet through the firewall to your AC controls.

What causes a 1993 Ford F150 to stall out?

Check for the following conditions: Poor connection at PCM or IAC motor. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection. Refer to Diagrams. Damaged harness. Inspect the wiring harness for damage. Restricted air intake system.

How much does it cost to replace a Ford Explorer transmission?

The 2002-2005 Explorer has a very well-established record of expensive transmission failure at under 100k miles. The Explorer has an enclosed transmission which is typically replaced with a rebuilt transmission at a cost of almost $3,000.

What to do if your Ford PCM is not working?

Without a properly working PCM, the Ford will not run. At times, you may want to perform a reset of the Ford PCM for basic troubleshooting. This can often resolve small issues that you may experience with the Ford. Open the hood of the Ford. Loosen the lock nut located on the negative battery cable connector with a socket and ratchet.

Why is my engine not responding to my ECM?

This can happen for any number of reasons, but usually, it’s a problem with your engine timing. While that function is directly controlled by the ECM, your PCM may also be at fault, since the ECM requires feedback from the PCM to adjust timing. 6.

Can a new starter cause an ECM to fail?

Installing a new starter can also cause ECM failure. This is because they often bypass the surge protector on the ECM, leading to a power surge when you start the vehicle. The same thing can happen if you get your wires crossed while jumping your car. A failing battery can also cause ECM failure.

Can a knock sensor cause a car ECM to fail?

There’s also a knock sensor on the engine itself. While these sensors aren’t likely to cause any catastrophic problems, failures in these areas can cause your ECM to make unnecessary adjustments that affect your car’s performance. In these cases, though, the problem is usually with the sensors, and not with the ECM.