What should I do if my Chevy 350 engine is not running?
What should I do if my Chevy 350 engine is not running?
Check for a fuel problem by spraying carburetor cleaner into the carburetor. Start the vehicle. If the vehicle starts, there is a fuel problem. If you have a mechanical fuel pump and the lines are not clogged, replace the mechanical pump. If you have an electric fuel pump, check the relay. If the relay is bad, replace it.
What is the cooling system on a Chevy 350?
The cooling system for the Chevrolet 350 engine consists of a water pump, a radiator and a thermostat. It is of vital importance that the cooling system work properly, as a cooling problem can lead not only to an engine which overheats, but also to more serious problems such as a damaged head gasket or a cracked cylinder block.
What to do if your Chevy 350 overheats?
Pull any insects out of the fins with tweezers. Severe clogging will prevent air from passing through the radiator and cooling the antifreeze, resulting in overheating. Twist off the radiator cap after allowing the engine to cool, then look into the radiator to observe the level of antifreeze.
What should voltage be to start Chevy 350?
If the voltage is below 12.00, the battery needs to be charged before further testing. Start the vehicle after charging the battery. Touch the battery terminals with the respective voltmeter leads as outlined in the previous step. If the voltmeter shows 13.50 to 14.75 volts, the alternator is charging properly.
How to troubleshoot an overheating Chevrolet 350 engine?
Twist off the radiator cap after allowing the engine to cool, then look into the radiator to observe the level of antifreeze. Pour antifreeze into the radiator until full if necessary. With the radiator cap off, start the engine and look through the radiator opening while the engine warms.
Where does the Chevy 350 crate engine come from?
Made in the U.S.A. Our famous “Hum Baby” Chevy 350 crate engine! She’s a smooth running machine that is suitable for a practical enthusiast looking for a higher quality engine than what GM offers. We took the “Hum Baby” engine and added more performance parts, bigger cam for that extra sound, and more performance without losing dependability!
The cooling system for the Chevrolet 350 engine consists of a water pump, a radiator and a thermostat. It is of vital importance that the cooling system work properly, as a cooling problem can lead not only to an engine which overheats, but also to more serious problems such as a damaged head gasket or a cracked cylinder block.
What kind of engine does a Chevy 350 have?
Fits trucks and SUV’s from 87-95. An easy installation, lots of power, street-friendly for daily driving and light towing this guy does it all! Fits full size trucks and SUV’s from 96-02, also known as a VIN “R” engine.
Why is my GMC Sierra 1500 stalling and dying?
There is no code given. Have changed the injectors, timing, fuel tank, fuel pump, fuel pump, map sensor, cooling temp sensor on front of block, rebuilt the tbi, air idea valve. None of this hasite helped. The truck starts and dies. Have to give a little gas to keep running. While driving have to 2 foot it so it won’t die.
Why does my 1993 Chevy TBI stall at idle?
Timing is steady and not jumping all over. It is a fuel issue. The only code that ever sets is a P044, lean exhaust, and the exhaust is really lean. We have swapped PCM/PROM with a same year Suburban, no change. Both vehicles run the same as this did using the other’s PCM.
There is no code given. Have changed the injectors, timing, fuel tank, fuel pump, fuel pump, map sensor, cooling temp sensor on front of block, rebuilt the tbi, air idea valve. None of this hasite helped. The truck starts and dies. Have to give a little gas to keep running. While driving have to 2 foot it so it won’t die.
Why did my GMC truck engine die while driving?
The positive battery cable was coroded and chewed up. Replaced it and all has been well.
Why does my Chevy truck shake at idle?
While the truck is idling with 02 lean, a quick shot of carb spray in the throttle body will cause the 02 to go rich. And when the truck sometimes starts shaking at idle it will smooth out with carb spray. I jst don’t understand why the computer is not trying to richen the mixture up based on the 02 saying lean.
What’s the fuel Gage on a 1993 Chevy truck?
Fuel gage never wavered at 12-13 psi. MAP around 2.9v when PW 2.8MS when truck seemed to be falling a little flat under brake torque. This thing is really close to getting a carburetor on it.
Check for a fuel problem by spraying carburetor cleaner into the carburetor. Start the vehicle. If the vehicle starts, there is a fuel problem. If you have a mechanical fuel pump and the lines are not clogged, replace the mechanical pump. If you have an electric fuel pump, check the relay. If the relay is bad, replace it.
Why does my Chevy 350 backfire when I accelerate?
If you hear a pop sound under the hood when you accelerate it is most likely running lean (Not enough fuel) from either a vacuum leak or the fuel pump failing (low fuel pressure). The 90 degree elbow in the PCV Valve hose at the base of the throttle body to the PCV valve is common to either fall off or have a hole in it.
What causes an engine to run too rich in fuel?
If this is faulty and telling the engine control module to add more fuel, even if the air-fuel ratio is good – it may cause a rich fuel mixture. A faulty O2 sensor can cause the engine to run too rich.
Can a faulty fuel pump cause poor mileage?
Poor Mileage. A faulty fuel pressure regulator can also be to blame for a sudden decrease in fuel mileage. Alternatives. These symptoms can also occur with a plugged fuel filter, failing fuel pump, or faulty PCM. In the event you have these symptoms, it is best to have the entire fuel system inspected by a qualified Ford fuel system technician.
How to know if your engine has no spark?
First Confirm Your Engine Has No Spark. 1 Disable the fuel system by removing the fuel pump fuse or relay. 2 Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. 3 Finally, Have someone crank the engine and watch for spark.
What causes a fuel injected engine to get wet?
Wet fouling is less common on modern fuel-injected engines, but can happen due to a number of mechanical failures, states AA1Car.com. One example is a leaking cold start injector. This would lead to the creation of a rich start up mixture in the engine compartment that would cause the plugs to foul.
What causes oil to come out of fuel pump?
Where the fuel pump mounts to the timing case cover a gasket provides a tight seal. Although this gasket is usually reliable, engine vibration can cause the bolts to come loose. When this happens, oil can seep out around the fuel pump.
First Confirm Your Engine Has No Spark. 1 Disable the fuel system by removing the fuel pump fuse or relay. 2 Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. 3 Finally, Have someone crank the engine and watch for spark.
Why does my 350 Chevy truck not start?
350 chevy truck cranks but won’t start – Maintenance/Repairs – Car Talk Community Truck ran fine with no indication of problem. When outside temp. dropped in teens one morning it wouldn’t start.
Why does my spark plug smell like oil?
Oil fouled spark plug Heavy black deposits with an oily appearance. These are the result of oil entering in the combustion chamber, probably past worn valve guides, guide seals or rings.
Why does my GM pickup engine not start?
How To Test The Fuel Pump On GM TBI Fuel Systems (for throttle body fuel injection fuel system equipped vehicles). A failure in one of the Passlock system’s components will cause the engine to start and then stall after a few seconds. This is due to the fact that the PCM, in your GM pickup or SUV, has disabled the fuel injectors.
What to do if your Chevy truck won’t start?
Would crank normally but not start. Found no spark. Replace HEI distributor and no start. Have replaced spark plugs, had starter and battery tested. All are good. Edelbrock 600cfm carb is 6 months old. Truck was completely restored 20000 miles ago so mechanically it’s a new truck.
Pull any insects out of the fins with tweezers. Severe clogging will prevent air from passing through the radiator and cooling the antifreeze, resulting in overheating. Twist off the radiator cap after allowing the engine to cool, then look into the radiator to observe the level of antifreeze.
Why is my Chevy truck cranking but not starting?
Too slow is either a starter motor problem or a electrical supply issue. Too fast can indicate a broken timing chain for example. Not sure why you changed the starter motor unless it was turning the engine over too slowly. If it cranks normally, it’s not the starter motor… How did you verify spark?
Is the 98 Chevy 5.7 misfire running right?
I have a 98 chevy 1500 5.7. The truck doesnt run right at all. Msifres bad under acceleration. Idle ok when misses when reving and accelerating. I did a full tune up including plugs, wires, cap rotor and a new distributor. With key on i have about 60psi fuel pressure but idleing i only had 50psi.
How to fix a 98 Chevy 5.7 Vortec?
I had same problem 97 5.7 vortec. Replaced cam and crank sensors repaired wiring to crank sensor, much better. I put it on co. Outer and it said can and crank sensors were not in sync with eachother adjusted timing got it down to 2 degrees, it can be – 2 or +2 but no more than 2 16 people found this helpful.
What’s the misfire code on a 1998 Vortec?
Can someone please help with what I should check next, I have a 1998 Chevy K1500 5.7 Vortec with a misfire, P0300 code for 3 months. runs a little rough, while driving under normal conditions it sputters, hesitates, and also will backfire, under heavy acceleration no noticeable skip, no sputters, and does not hesitate or backfire.
What kind of fuel injector does Chevy Silverado use?
Chevy Silverado Misfire , Dirty Injector ,.This 1999 Chevy Silverado was running badly and had a misfire. The Chevy Silverado hooked up to the Scanner showed a misfire on number eight cylinder .The 5.3 in the chevy Silverado is easy to switch ignition coil and plug wire with another cylinder.
Why does my car have dirty fuel injectors?
Dirty fuel injectors can be diagnosed through an exhaust gas analyzer because restricted injectors create higher hydrocarbon and carbon monoxide readings. By using an injector cleaner additive regularly, you prevent this situation. Once the injectors are clogged or restricted, an injectable solution will need to be introduced into the system.
What causes hesitation and stumbling in a 1990 Chevy c1500?
An expert that got 10 achievements. Re: 1990 chevy c1500 hesitation and stumbling during… Based on what you said, I would say the engine is starving for fuel. The computer has to be disabled to set timing – there should be a procedure for that. I would start with checking fuel pressure at the throttle body.
An expert that got 10 achievements. Re: 1990 chevy c1500 hesitation and stumbling during… Based on what you said, I would say the engine is starving for fuel. The computer has to be disabled to set timing – there should be a procedure for that. I would start with checking fuel pressure at the throttle body.
How does the ignition work on a Chevy 350?
The engine’s ignition system is triggered by an electronic driver which signals the ignition coil when to fire. By design the resistance it takes to fire the coil via the spark plug is figured into the system.
What should fuel pressure be on 350 truck?
from 250hp to 260hp the fuel pressure should be bumped up to 13-14psi on stock 350 truck injectors which will change their flow rating to 60lb/hr From 270hp to 340hp you need to change the fuel pump as the stock pump can’t maintain pressure over 270hp and you need to run 18psi on the 350 truck injectors for a flow rate of 72lb/hr
Why does my GM 4.3L engine not start?
No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.
What should the fuel pressure be on a Chevy Cheyenne?
93 Chevy Cheyenne k3500, if it is running the Chevy vortec engine the fuel pump pressure is way too low, should be 56 psi+ depending on CSFI/CPI system or it will not start or open injectors, with out the aid of starting fluid. The factory manual specifies that the fuel pressure for the CSFI system should be between 56-62 PSI.
Can a lack of fuel cause a car to not start?
CASE 1: If the engine started and ran for a few seconds: This means that the reason your pick up (or SUV) is not starting is due to a lack of fuel. Now that you have confirmed that the ‘no start’ problem is due to a lack of fuel, you now need to actually confirm how much pressure the fuel pump is producing with a fuel pressure gauge.
Why does my fuel pump not turn on?
You don’t hear the fuel pump making a buzzing sound as you turn the key to the On position or crank the engine. You don’t see the fuel injectors spraying gasoline. Although the above list is a not a very complete list of symptoms, the theme that runs thru’ them, and any other related symptom, is that the engine will crank and crank, but not start.
Why does my 93 GM 3500 box truck not work?
I have a 93 GM 3500 Box Truck, it is a van chassis. Fuel pump quit working, now headlights aren’t. Battery has 13.1v in it. Cranks over and starts with ether, but no gas. I thought fuel pump was out so I bought a new one but haven’t tackled dropping the tank. Watched a youtube video about weak battery causing fuel pump to not work.
93 Chevy Cheyenne k3500, if it is running the Chevy vortec engine the fuel pump pressure is way too low, should be 56 psi+ depending on CSFI/CPI system or it will not start or open injectors, with out the aid of starting fluid. The factory manual specifies that the fuel pressure for the CSFI system should be between 56-62 PSI.
Why does my Chevy 350 backfire under load?
When high performance turbo engines are under load they use an excessive amount of fuel which then is transferred into the exhaust system once the throttle is let up on and the engine is de-accelerating. This is a normal event and there is no problem with this condition.
Why is the fuel pump on my Chevy 350 not working?
The mechanical fuel pump was replaced from the original C20 due to space restrictions (4 x 4) with a new fuel pump. Not sure, maybe it doesn’t have enough volume than the previous one. The fuel pump works fine while revving the engine at idle. I’m guessing it’s fine if it’s just based on a specific fuel pressure.
When did Chevy stop using the 350 engine?
Get the facts on the history and specifications of the Chevy 350 engine, finding replacements parts, and finding Chevy 350 crate engines for sale. Beginning in 1985, Corvettes featured a fuel-injected version of the Chevy 350 engine; other passenger cars equipped with the 350 engine continued to use a four-barrel carburetor.
When did fuel injection become standard on Chevy 350?
Computer-controlled emissions systems became standard on all Chevy 350 engines in the early 1980s, with throttle body fuel injection becoming standard around 1988.
What’s the engine code for a Chevy 350?
The majority of engine codes begin with the letter L — L31, for instance. Long considered one of the easiest engines to rebuild, the Chevy 350 is commonly modified for increased performance with a plethora of aftermarket parts, including high-performance intake and exhaust components.
Get the facts on the history and specifications of the Chevy 350 engine, finding replacements parts, and finding Chevy 350 crate engines for sale. Beginning in 1985, Corvettes featured a fuel-injected version of the Chevy 350 engine; other passenger cars equipped with the 350 engine continued to use a four-barrel carburetor.
What kind of ignition system does a small block Chevy use?
There are a lot of fancy ignition systems available for the small block Chevy but the simplest and most cost effective is still the HEI—but it needs a little hopping up to get the job done. A custom built Performance Distributors unit takes care of that.
The majority of engine codes begin with the letter L — L31, for instance. Long considered one of the easiest engines to rebuild, the Chevy 350 is commonly modified for increased performance with a plethora of aftermarket parts, including high-performance intake and exhaust components.
Computer-controlled emissions systems became standard on all Chevy 350 engines in the early 1980s, with throttle body fuel injection becoming standard around 1988.
What does it mean when your engine idle does not increase?
Use the command in the scan tool to increase the engine’s idle. If the engine idle does not increase, it means there is an issue at the idle control motor of its circuit preventing the signal from changing the idle. You can purchase a bidirectional scan tool at your local auto parts store.
What happens when the idle control motor is disconnected?
With the Idle Control Motor disconnected, get back into the vehicle and start the engine again. The engine should still start and run without any issue despite the idle control motor being disconnected. Be sure to tuck the wiring you disconnected up in the engine bay so it doesn’t get caught in any moving parts.
How can I tell if my idle control valve is working?
To check if an idle control valve is working properly, start by turning on your engine and letting it run for a minute or 2. Then, when it’s at an idling speed, take note of the RPMs in your car. Next, turn the engine off and disconnect the idle control motor under your hood.
Use the command in the scan tool to increase the engine’s idle. If the engine idle does not increase, it means there is an issue at the idle control motor of its circuit preventing the signal from changing the idle. You can purchase a bidirectional scan tool at your local auto parts store.
With the Idle Control Motor disconnected, get back into the vehicle and start the engine again. The engine should still start and run without any issue despite the idle control motor being disconnected. Be sure to tuck the wiring you disconnected up in the engine bay so it doesn’t get caught in any moving parts.
What’s the best way to time a Chevy 350?
Someone tell me the easy way to time a Chevy 350, 1977 made. Engine in CHEVY II 1967, HEI Mallory dist., carberated. 1. Engine at normal operating temp. 2. Idle adjusted correctly. 3. Remove and plug vacuum hose to distributor. 4. Hook up timing light to #1 spark plug wire.
Is there a problem with my 1990 Chevy truck?
I just recently purchased a 1990 Chevy 2500 single cab long bed with the 350 tbi that has been D.O.T inspected until 2018 in MN. The issue – it has a fuel delivery problem and the previous owner was fairly certain that it needed a fuel pump and I wasnt surprised cuz ive had to do that with past 90s gm trucks.
What kind of fuel problem does a 1990 Chevy 5.7L have?
Click to expand… It probably won’t be the TPS since you sprayed ether and it fired but died after.
Where is the tach on a 1990 Chevy truck?
That white wire on the coil is the feed for the tach in the dash, if your truck didn’t come with one it’s left unhooked. and found a good ground then had my gf turn key and slowly pump the peddle and the highest number was 2.1 with the peddle to the floor.
Why does my oil pump make a whining noise?
Lastly, your oil pump may begin to make noise if it isn’t working properly. This is a less common problem than some of the others presented here. If your oil pump begins to make noise it will be a loud whining or whirring sound.
What causes the fluid level to drop on a Chevy 350?
The drop is caused by the thermostat at the end of the top radiator hose opening. Replace the thermostat if the fluid level does not drop. Look for white smoke exiting from the exhaust pipe, which indicates a blown head gasket.
Where does the oil go in a 350 Block?
The plug is in there Fritz, and we measured the same as you did with a rod. We used my old 350 block to pop the rear cam plug, front and rear cam bearings, and oil galley plugs out of the block to see where oil gets routed.
What’s the oil pressure on a Camaro 350?
When I first start this vehicle, the oil pressure is great (around 40-50 psi), but as the engine temperature increases, the oil pressure drops. After the motor is completely warmed up (around 190-200 degrees) the oil pressure gets very low (at 0 / almost 0).
How much oil does a Chevy 350 have?
The Chevy 350 oil capacity is at 5 quarts, if it’s an unmodified stock model. Previous Simple Ways to Upgrade Your Car Next Don’t Panic, I’m a Mechanic: Smart Cars
Lastly, your oil pump may begin to make noise if it isn’t working properly. This is a less common problem than some of the others presented here. If your oil pump begins to make noise it will be a loud whining or whirring sound.
The engine’s ignition system is triggered by an electronic driver which signals the ignition coil when to fire. By design the resistance it takes to fire the coil via the spark plug is figured into the system.
Why does my Chevy 350 backfire when I let off the gas?
If it backfires when you let off the gas peddle it has air getting into the exhaust, either an exhaust gasket or cracked manifold before the catalytic converter or the emission control’s Air Injection system. The air injection check valves (STANDARD MOTOR PRODUCTS PT#AV7) are common failure parts.
Is it normal to have a rough engine idle?
Consequently, rough engine idle, is not a normal operating condition. As a result, there can be a variety of reasons for a, rough engine idle. It is best to try to diagnose and fix a rough engine idle; before it gets worse and before it gets expensive!
Why does my GMC Sierra 1500 run rough at idle?
The spray smoothing out the rough rpm is an indication of the engine running lean, could be low fuel pressure, could be a vacuum leak. With it running rough at an idle and smoothing out at a higher rpm is a general sign of a vacuum leak.
Why is idle speed not coming back up?
If the ISC system is working correctly, the PCM should adjust idle speed to keep the engine from lugging down when the A/C compressor engages. If idle speed drops down and does not come back up, the ISC system is not responding the way it should.
What does the fuel smell like in a GMC Sierra 1500?
If so pull the air filter off and sniff the throttle body for a fuel smell. If the diaphragm has ruptured it will literally be like putting a hose with fuel into the intake and running it full.