What kind of truck has a Telsta boom?

Discussion in ‘ Shop Talk ‘ started by onedavo, Jul 13, 2015 . I recently bought a 1997 Ford Super Duty truck equipped with a Telsta boom. It is working good now but I have no manuals and no experience with this type of equipment.

What kind of wiring does a Telsta bucket truck use?

Telsta A28D Wiring Diagram Telsta Bucket Truck Wiring Diagram Boom Truck Wiring Diagram – Free Telsta A28D Wiring Diagram Lift Boom Altec AtA For Small Bucket Utility Trucks – Youtube SHARE ON Twitter Facebook Google+ Pinterest. Need wiring diagram for a Telsta bucket aerial lift.?? It’s on a old cable Truck 1 ton dually.

What should the torque be on a Telsta boom?

Torque specs for the cover bolts would just be standard dry torque for those fasteners, I can’t remember if they are 1/4 or 5/16 but you can easily look up the torque, but it’s not critical. Back to your generator, a lot of those units had the ability to start and stop the generator from the basket, to save fuel and reduce noise.

How often should I change the lubricant on my Telsta boom?

From reading the manual it appears the azimuth drive gears and the azimuth drive are two different animals and require different lubrication. The drive uses a spray lubricant and is supposed to be checked every six months. I can see it and not worried about it right now.

Can a Telsta boom be used with a bucket?

With the bucket raised there is no load on the pump. Also just for your information all cylinders on an aerial lift are required to have holding valves built into the cylinder, in order to hold a load.

How big is the rotation gear on a Telsta boom?

The rotation gear is about a foot in diameter and you can see it by taking off the fiberglass (or some similar material) cover. That is the horizontal part of the “T.” Above that is a housing and at the top of the housing is a plate bolted on.

Where are the lower controls on a Telsta?

Telsta units were often built with a manual rack in the rear curbside compartment where the lower controls are located. I hope that helps. Found it! I dunno if I feel more like Columbo or the kid who just found the prize Easter egg.

Where is the level plug on a Telsta boom?

Also just for your information all cylinders on an aerial lift are required to have holding valves built into the cylinder, in order to hold a load. So to check the level in your gearbox I would raise the boom ask the way up in the air, you can kill the engine if you want, then I believe the level plug is located on innermost side.

What is the filename of de-ice s1.100?

Filename: De-ICE_S1.100.iso To make sure that the files haven’t been altered in any manner, you can check the checksum of the file. This makes sure that the you have acquired the same file which was transferred to you, without being modified/changed/damaged.

What kind of equipment does Walton de ice use?

W.B. Walton Enterprises Inc. (Also known as Walton De-ice) designs and manufactures the broadest line of equipment available for preventing the accumulation of snow and/or ice on satellite earth station antennas.

How big is a full size de ice antenna?

The original De-Ice products designed by W.B. Walton Enterprises includes a behind the antenna plenum (enclosure) which is heated with hot air. These systems for antennas ranging in size from 3.7-meter to 32-meters in diameter.

How big is a great FBO deice truck?

For sale, great FBO Deice truck. 1994 Stinar Deice truck on a 1 Ton GMC Chassis. 1000 gallon type 1 capacity. 36 ft boom height, easily reaches all corporate aircraft tails. David Clark, inter… See More Details

What kind of equipment is used to remove ice?

De-icing, anti-icing, snow removal, and other, similar equipment help tackle the job of removing ice and snow from a variety of aircraft and airport surfaces and preventing additional buildup from forming again prior to takeoff. This truck is ramp ready for both type 1 and type 4 glycol.