What is the wheel nut torque specifications?
What is the wheel nut torque specifications?
New wheels should be re-torqued after the first 50 to 100 driving miles.
| Hardware Bolt or Stud Size | Typical Torque Range in Ft/Lbs | Minimum Number of Turns of Hardware Engagement |
|---|---|---|
| 12 x 1.5 mm | 70 – 80 | 6.5 |
| 12 x 1.25 mm | 70 – 80 | 8 |
| 14 x 1.5 mm | 85 – 90 | 7.5 |
| 14 x 1.25 mm | 85 – 90 | 9 |
Should you torque locking wheel nuts?
They should be nipped up a bit more than finger tight, but not fully torqued, as getting them off on a journey when you have a flat could leave you stranded… The other normal wheel nuts should be fully tightened and torqued, and they will hold the wheel in place even if the locking nut comes loose.
What should be the torque of a bolt?
not present B Bolt Tension Corresponding to 65 Recommended Assembly Torque D Diameter P Pitch k kN N Nm M M1.6 0 0.35 0 0.19 0 0.06 M M2 0 0.40 0 0.31 0 0.12 M M2.5 0 0.45 0 0.50 0 0.25 M
What are the torque settings for zinc plated fasteners?
Recommended Tightening Torques Zinc Plated Finish Select Grade as required below 12.9 / 10.9 / 8.8 Maximum Recommended Tightening Torques Metric Coarse Pitch Grade 12.9 Plated Metric Coarse Pitch Grade 10.9 Plated Metric Coarse Pitch Grade 8.8 Plated Ncm in-lb Ncm in-lb Ncm in-lb
Where are the torque settings on a MG?
Bolt/fixing Nm ft.lb Engine Engine Engine Camshaft cover bolts 9 7 Camshaft gear bolt 8mm bolt 10mm bolt 33 65 24 48 Crankshaft pulley bolt 205 151
What are the recommended torques for an assembly?
Bolt Tension Recommended Corresponding to Assembly 65% of Proof Load Torque kN Nm 3.17 1.9 5.54 4.4 8.97 8.9 12.7 15 23.1 37 36.6 73 53.2 128 72.8 203 98.8 316 121 436 155 620 191 840 222 1066 289 1561 354 2124 437 2884 515 3708 Page 3
Where can I find the latest torque specs?
Find the most up-to-date torque spec listings in electronic format. FelPro-Only.com is your convenient source for advanced sealing information. It’s the place to learn and share “tricks of the trade,” find proper diagnosis and installation instructions, and enjoy easy access to parts reference.
What should the torque be on a torque table?
Torque specifications are shown either as an exact figure, or a specific range. Follow any special instructions or multi-step directions carefully to assure correct final torque. There may be different specifications for different size bolts, bolts in different positions, tightening bolts in several stages, or a cold engine vs. a warm engine.
How often should I torque my leaf spring?
Remember, torque your bolts to the recommended specifications immediately upon installation, and re-torque the U-bolts after 50 miles. and then again after 500 miles. And heck, it’s a good idea to check them every time you’re underneath your vehicle. Remember, tight U-bolts will extend your spring’s life and performance.
What’s the maximum tightening torque on a screw?
The maximum tightening torques are: Only applicable to shaft screws with metric standard and fine threads acc. to DIN 13, sheet 13 and nuts with height of 0,8 x d acc. to DIN 934 and only for a µ total = 0.125 (screws phosphatized, screws untreated or galvanized. Lubrication condition: unlubricated and also oiled).
