What is the fuse diagram for a Chevy S-10 Blazer?

Diagram (1985-1994) № A Circuit Protected 9 15 1988-1994: Rear/Four Wheel Anti-Lock Bra 10 25 Heating & A/C 11 30 Circuit Breaker: Power Windows 12 10 1993-1994: Daytime Running Lights

When did the Chevy’s 10 come out?

Chevrolets compact pickup truck, the S-10, was marketed in North America between 1982 and 2004. Chevrolet made two generations of North American Chevy S-10 trucks with a number of trim models, including the S-10 Blazer, extended, and single cab Chevrolet S-10 versions.

What kind of Fuse is in Oldsmobile Bravada?

Oldsmobile Bravada (1990-1994). The wiring circuits in the vehicle are protected from short circuits by fuses. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse.

Where is the fuse panel on a blazer?

Never replace a broken fuse with anything other than a new fuse. Use always an intact fuse of the same color. If a fuse blows again contact a qualified service center. The fuse panel is located under the dashboard. 1988-1994: Rear/Four Wheel Anti-Lock Brake Module, Digital Radio Adapter Module, Speedometer, Auto.

Why is my Chevrolet S10 4×4 not working?

(Diagnose and Fix) – YouTube Chevrolet S10 4×4 Not Working? (Diagnose and Fix) If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.

What kind of wiring does a Chevy Blazer have?

WIRING INFORMATION: 1989 Chevy S-10 Blazer WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT RED Ignition Harness STARTER YELLOW OR PURPLE Ignition Harness IGNITION PINK Ignition Harness ACCESSORY ORANGE Ignition Harness POWER DOOR LOCK (5-wire reverse polarity) LT.

Is there a Repair Manual for a Chevy Blazer?

You Fix Cars has auto service repair manuals for your Chevrolet Blazer – download your manual now! Chevrolet Blazer service repair manuals

When to replace a fuse on a blazer?

Replace the fuse as soon as possible. Before replacing a fuse check that the key has been removed from the ignition and that all the services are switched off and/or disengaged. Do not repair fuses and never replace a blown fuse with one that has a higher amp rating. This can cause damage to the electrical system and fire.

What should I do if my S10 engine Jerks?

Pull your oil cap and hold your hand over the hole while it is idlling. You shouldn’t hear or feel any compression blowby from any cylinders. If you do, try a thicker grade oil.

What are the Illuminations on a Chevy Blazer?

Cluster Illumination, Radio Illumination, Heater Lamp, Four-Wheel-Drive Illumination, Chime Module, Fog Lamp Illumination, Rear Wiper Switch, Rear Defog Switch Illumination, Liftglass Release Switch Illumination, Overhead Console Illumination

Is the 4×4 light on on my Blazer?

I read what you said about the wires on the Blazer, but mine were not corroded. I took it off and cleaned it up anyway and it came back on, but as soon as I turned the key off she was gone again. I don’t have any lights lighting up on the 4×4 switches. Service 4X4 light is on in the dash. I don’t know what is going on.

Is the 4Lo button on a blazer working?

I also now notice (in testing it) that the Auto 4WD, 2HI, and 4HI buttons work, but that the 4LO button just blinks when pushed (in neutral). I have to push one of the other buttons to get out of it.

Is there an amp in the back of my Blazer?

Well, just before this starting happening, my son and I installed a sub and amp in the back of the Blazer.

Is there a problem with my Chevy Blazer 4×4?

Yes my name is kyle and I have a 1999 chevy blazer 4×4 and i have the same tccm problems like everybody else but my only problem is that i need the new 32 pin femal plug and the 4pin female cause my tccm is in working condition. I can’t find then plugs and wires anyplace i know what are odds there.

I also now notice (in testing it) that the Auto 4WD, 2HI, and 4HI buttons work, but that the 4LO button just blinks when pushed (in neutral). I have to push one of the other buttons to get out of it.

Well, just before this starting happening, my son and I installed a sub and amp in the back of the Blazer.

Why does my Blazer vibration go away when turning left?

You were RIGHT ON when you said that it was coincidental with having installed an amp. As an FYI for you and your readers: They diagnosed the problem as a bad bearing (driver side, front). They said the reason the vibration went away when turning left was because the weight of the Blazer shifted to the right side.

What to do when Your Fuse goes out on your car?

To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure to replace a bad fuse with a new one of the identical size and rating. Fuses of the same amperage can be temporarily borrowed from another fuse location if a fuse goes out.

Why does my ECM 1 fuse keep blowing?

If the wires leading to the O2 sensor rub against the exhaust, it creates a ground; once the O2 sensor is grounded, the fuse to the ECM 1 blows. The O2 sensor must be installed in a different place to ensure the wires do not short-circuit.

What causes a fuel pump fuse to blow?

When the fuel pump begins to fail it overheats, causing it to drain more amperage (amp); if the amps exceed the amount of amps the ECM 1 fuse allows, the fuse will blow. Replacing the fuel pump should correct this problem. The ECM 1 operates via voltage sent from the battery.

Where are the fuses on a Chevy Blazer?

The fuses are located below the dash panel. Horn, Dome & Glove Box Lights, Clock, Courtesy Lights (1982-1984), Lift Gate Release Solenoid (1982-1984), Cigarette Lighter

What is the fuse box diagram for a Chevy truck?

Chevy Truck Fuse Block Diagrams – Chuck’s Chevy Truck Pages Chevrolet truck fuse box diagrams. 1973 – 1979 fuse box diagram. !980 – 1987 fuse box diagram. Great resource if the lettering is worn off yours

How does the ECM work on a Chevy truck?

Every Chevrolet truck has an engine control module that manages the electronic components of the engine and monitors sensors for errors. Returning the ECM to its factory state may be necessary to troubleshoot or resolve a number of problems. Step 1 Remove the nut from the negative battery cable using a socket set or wrench.