Easy tips

What happens when you remove the key from the ignition?

What happens when you remove the key from the ignition?

Car Engine Doesn’t Turn Off When Removing Key or Pressing STOP It is a strange problem to have a car that won’t turn off when you remove the key from the ignition or press the Engine Stop button. Your engine will continue to run even when you remove the key from the ignition because the fuel pump is not shutting off.

Why does my car keep running after I remove the key?

Here are the most common problems that cause the engine to keep running even after removing the key from the ignition or press the STOP button. The ignition module may fail, or if your car is equipped with an Engine Push to the Start button, the Keyless module could be the culprit.

What drains a car battery while it is off?

So you ask yourself, what drains a car battery while it is off? Most common reasons why your battery drains is because you left your headlights overnight, clock, radio, and security alarm that runs after your car is turned off, bad charging, defective alternator diode, and old battery.

What happens when you turn off your car battery?

Parasitic drain: This happens when your accessories continue to run even after you turn your vehicle off. This can be your dash clock, your radio, and your security alarm. Bad charging: If your battery isn’t charging properly, you can end up calling the tow company.

Why does my car key not turn when I put it in the ignition?

If your key won’t turn when you insert it into the ignition, it may be because the key has been damaged and no longer engages the correct pins to the depth necessary to spin the cylinder. Examine the key for signs of excessive wear, rounding or broken teeth.

What happens when you turn off the engine with the car in drive?

Accidentally turned off engine with car in drive – Maintenance/Repairs – Car Talk Community First time car owner and I feel like a complete potato after turning off my engine with the car still in drive. I parked my car and then turned off the engine and tried to pull out my key. It wouldn’t let me pull out my …

What happens if you wiggle the ignition key?

Be careful not to apply too much pressure. Wiggling the key can make the key contact the pins from a different angle, which may allow you start the vehicle. If wiggling the key works, it means the teeth on the key are too worn to properly engage the pins. Replace the key as soon as possible if this works before the key stops working entirely.

What should I do if I accidentally turned off the engine?

If there are no symptoms you could just ignore it, but if having a car that starts and runs reliably every time you turn the key to start it, probably makes sense to take it in for a pro-active inspection. Barkydog April 14, 2017, 12:57am #3 You will be fine, no worries. Thank you for asking, and motor on!

How do you unlock the radio on a Chevy Silverado?

Jot down the four-digit number with which you will be provided twice. You can turn off the ignition while you make the call. You should once again see “LOC” on the radio screen. Using the hour and minute buttons on your radio control, enter the phone code to unlock your radio.

How long do you leave the key in the ” on ” position?

Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2. Turn the ignition switch to the “OFF” position for 30 seconds.

Is there a way to unlock a Chevy truck without keys?

You might think twice about parking it on the questionable sidestreet now. Instead of learning how to unlock a Chevy truck without keys, you can get a magnetic box and put a hide-a-key somewhere on the outside of your vehicle. Just be sure to wedge it in a spot where it won’t be easily found or fall off when driving.

How to program Chevy Gm key with no keys programmed?

The programming of any of these Gm keys is relatively easy and most of them can be programmed yourself DIY. If you have at least 1 working key…. If all keys are lost…. Then you must perform what we call the 10x10x10 procedure: Insert new key and turn on (do not start!)

How do you turn off PassLock on a Chevy?

Key on, press volume till readout says SETTINGS then scroll to the Security to toggle off by pressing reset ( watch YOUTUBE). I personally see no sense of having no security system so try the RELEARN method. Other thing is that the Ignition Switch has a Sensor on it and the wire clip comes loose.

What happens if you lock your keys in Your Truck?

Locking your keys inside your truck is a rookie mistake! It happens to everyone at least once. However, you don’t have time to wait for a locksmith to come and get your truck open. You could break a window, but then you’d have to buy a new one and that sounds a little expensive.

What to do if your ignition switch won’t work?

Step 7 – In extreme conditions such as high mileage or a key chain adorned with many ornaments can wear the tumbler which causes the key not to work. If the door key is same as the ignition key, the door tumbler can be removed and a key made if no security chip is installed, (older cars).

Do you have to have a new ignition cylinder installed?

Just like having a new key cut, you will need to demonstrate sufficient ownership of the vehicle in order to have a new ignition cylinder installed. A new ignition cylinder will likely require replacing your key, even if it wasn’t the issue.

What can I use to make my ignition key turn?

Purchase canned air from a local retail or office supply store and insert the straw from the nozzle directly into the key hole. Spray the canned air into the key hole in short spurts.

What to do if your ignition key won’t turn?

This feature is not available right now. Please try again later. Sometimes the ignition key won’t turn or rotate. If that happens the vehicle won’t start, the steering wheel won’t turn and it won’t shift into gear. On a late 90’s or early 2000 GM vehicle this is the way to get it apart so you can replace the tumbler. Loading…

What to do if your ignition switch is stuck?

Step 1 – All vehicles have a steering wheel lockout safety device that will not allow the steering wheel to turn when the key is in the “OFF” position. Step 2 – Vehicles equipped with power steering utilize a pump which maintains pressure while the engine is running.

How do you change the ignition on a car?

Find the locking pin on your ignition assembly. Use a tool of the correct size to depress the lock pin. Pull the old ignition cylinder lose. You might need to shake the ignition cylinder loose or finesse it out of its housing. Insert your new key into the new ignition cylinder. Fit the new ignition cylinder into the housing.

Why does my car not start when I put the key in?

Putting the key in the ignition switch and starting the car feels like second nature. However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems.

Can a car still start when the ignition switch is out?

Yes, ignition SWITCH. In the interim, when you notice the car still running, try just wiggling the key to see if it moves the switch enough to shut off. Plan now to replace the switch. Most customers in the shop do not realize that the KEY CYLINDER is not the ignition SWITCH. ( Many of them come to my counter asking for a ‘’ key switch’’.

What happens if you turn off the engine without a key?

The ignition cylinder is mechanically connected to the steering wheel lock, so a potential thief cannot steer the car without the key. If you turn off the engine with the steering wheel turned or turn the steering wheel after turning off the engine, the steering wheel lock can bind and prevent you from turning the ignition.

Car Engine Doesn’t Turn Off When Removing Key or Pressing STOP It is a strange problem to have a car that won’t turn off when you remove the key from the ignition or press the Engine Stop button. Your engine will continue to run even when you remove the key from the ignition because the fuel pump is not shutting off.

Here are the most common problems that cause the engine to keep running even after removing the key from the ignition or press the STOP button. The ignition module may fail, or if your car is equipped with an Engine Push to the Start button, the Keyless module could be the culprit.

Can you remove the ignition key on a GMC Acadia?

Make and Model > GMC Trucks > Acadia > Can’t remove the key from… Diagnose and fix GM to correct situation where you can’t remove the key from ignition If you encounter a situation where you can’t remove the key from ignition on a GM vehicle, you have lots of company.

What to do if your ignition key is bent?

Bent keys can sometimes enter the ignition cylinder, but once inside will not line up correctly to allow the car to start. If your key looks visually bent, you can use a non-metal hammer to carefully flatten the key down. Your goal is to use something that will not damage the key, so ideally this would be made of rubber or wood.

What to do if your windows go down with ignition off?

Not a lot of folks have been experiencing issues with carbon, but Ford’s position is, if carbon is a problem for a customer, the suggested repair is to replace the intake and/or head. Some folks have been experimenting with catch cans, but very few.

What happens if you have an incorrect ignition code?

The chip in the key transmits a specific code, of which there are millions. If this code matches the ones programmed into the vehicle, engine starting is enabled. An incorrect key code, such as from an unprogrammed key or damaged key, would prevent engine starting. Code “confusion,” such as having multiple keys can also occur, preventing ignition.

What should I do if my ignition switch is not working?

How To Fix It: After ensuring the rest of the electrical system is intact, such as fuses, relays, and circuits, replace the ignition switch. The transponder antenna surrounds the ignition cylinder. If it doesn’t recognize the transponder key, it doesn’t allow the engine to run. https://www.gettyimages.com/license/525320791

Can a unworn key turn an ignition cylinder?

Or, an unworn key may not turn a worn ignition cylinder, as they haven’t “worn together.” How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders.

Not a lot of folks have been experiencing issues with carbon, but Ford’s position is, if carbon is a problem for a customer, the suggested repair is to replace the intake and/or head. Some folks have been experimenting with catch cans, but very few.

What happens when I cut the radio off and take the keys out?

What Im saying is when I cut the car off and take keys out, the radio doesn’t cut off and the windows still are able to work AFTER I OPEN THE DOOR. Will that drain the battery? it just doesnt fell right cause I dont wanna be stranded any where because of this. I will need more information to get you a more accurate answer.

The chip in the key transmits a specific code, of which there are millions. If this code matches the ones programmed into the vehicle, engine starting is enabled. An incorrect key code, such as from an unprogrammed key or damaged key, would prevent engine starting. Code “confusion,” such as having multiple keys can also occur, preventing ignition.

Why is my car not turning on when I Turn on the ignition?

Of course, if you access the car itself with your key, you likely won’t be able to turn on the ignition because of all those extra tumblers. And on the off chance that you do turn the ignition cylinder, the immobilizer won’t allow you to start the car, because it’s protected by one-in-millions of transponder codes.

What to do if your Silverado won’t shut off?

I have an “02” Silverado that won’t shut off with the key. The key works like normal but engine keeps running, Anybody have any ideas? Sounds like the ignition sw. to me. Any help will be appreciated, Thanks. Click to expand… To get it to shut off? Pull a main fuse from the underhood fuse panel.

Why does my GMC truck not shut off?

OK, new ignition sw & harness installed, alarm system disabled. It puts all kind of codes in it. It’s been at the shop for almost 6 days and the tech’s have been working on it. It is a RAMDOM problem, don’t do it all of the time. Any more ideas? Any help will be appreciated. Thanks.

Of course, if you access the car itself with your key, you likely won’t be able to turn on the ignition because of all those extra tumblers. And on the off chance that you do turn the ignition cylinder, the immobilizer won’t allow you to start the car, because it’s protected by one-in-millions of transponder codes.

Can you turn off the engine without the ignition?

The ignition in my 98 has been acting weird for some time. I can pull the key from the ignition while the truck is running. If you are not careful, you can turn the engine off without putting the key in the off position. The key will come out in the accessory position and you can turn the ignition with no key and start the truck.

Can a Silverado run without the ignition switch?

Silverado stayed running without the key in the ignition switch Hopefully someone can help me out here? I have a 2008 silverado crew cab which i am recently having problems with.

What causes a car key to stop turning?

There are several reasons why the key may have stopped turning the ignition. Your car key may have stopped turning the ignition because of a safety feature of the car, broken or damaged wafers in the ignition or a bad key.

Why does my starter not work when the key is off?

Starter buttons do not work when the key is off, so this would indicate a short to ground. Messing around switching solenoids may have jiggled it enough to make it seem fixed. You may want to run a whole new wire from solenoid to handlebars to make sure your problem doesn’t come back. Remove ads, support ADV.

What makes the chime on the ignition go off?

The functions that provide an audible warning are the key in ignition, the lights on, the occupant restraint (seat belt) and the park brake. The BCM will provide an audible chime if the key is left in the ignition in either OFF or the accessory position with the driver’s door open.

Why does the key in ignition not shut off?

The repaired cylinder has been replaced (I removed one set of tumblers that was out of place), the key turns fine – accessory, start features all work as intended. Any suggestions on why the chime does not shut off when the key is removed?

Putting the key in the ignition switch and starting the car feels like second nature. However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems.

How does the key in ignition chime work?

The body control module (BCM) monitors the state of the key-in-ignition switch, the state of the ignition switch (OFF, ACC, or RUN) and the driver’s door to control the key-in-ignition chime. My Chevy Venture 2003 door chime on drivers side chimes without key in ignition with door open.

Can a bad ignition switch cause a car not to start?

However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems.

What’s the best way to fix an ignition switch?

How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders. The ignition switch itself is connected to the ignition cylinder by a shaft or lever.

Can a key be programmed to an ignition switch?

Ignition switches can now be programmed to electronic ignition keys to add extra security and safety to your vehicle. These keys are synced with your engine to start your car, and once you program them, only a programmed key will start your car. Also question is, does a new ignition switch require a new key?

Ignition switches can now be programmed to electronic ignition keys to add extra security and safety to your vehicle. These keys are synced with your engine to start your car, and once you program them, only a programmed key will start your car. Also question is, does a new ignition switch require a new key?

How do you add a spare key to an ignition?

There is a different procedure to add a spare key. 1. Insert the non programmed key in the ignition and turn to RUN. 2. THEFT indicator flashes rapidly. 3. After 15 minutes of flashing, the THEFT indicator will stop flashing. 4. Within five minutes after the THEFT indicator has stopped flashing, turn the ignition key to OFF and back to RUN. 5.

How do you change the ignition key on a GM circle plus?

Within 10 seconds insert the new key and turn ignition to ON position. After about 5 seconds, when the security light turns off, remove the new key from ignition. Insert old working key and start the engine. The new key is programmed! Insert the new key and turn the ignition to ON position – security light will turn on.

Why is my car key not turning in the ignition?

Here are some of the most common causes of a key not turning in an ignition: Your steering wheel is locked: If you happen to move your steering wheel to the left or right after you turn your car off and remove your key from the ignition, it can make it difficult to turn the key the next time you put it back into the ignition.

Can a bad ignition switch cause a car to not turn over?

The vehicle will not be able to turn over because the electrical wiring in the electric switch isn’t able to communicate with the battery, and the vehicle’s accessories will function poorly (lights dim or not working). Problems in the vehicle’s lock cylinder will impact the driver’s ability to insert the starter key into the lock housing.

Why does my car engine not turn off when I remove the key?

Your engine will continue to run even when you remove the key from the ignition because the fuel pump is not shutting off. This problem is typically caused by a faulty fuel pump relay or a defective ignition switch. In this article, we take a look at why your engine won’t turn off when removing the key and what you can do to stop the engine.

What kind of truck won’t shut off with a key?

Won’t shut off with key. Data says key is in run position when key is off. Already verified the key switch is working correctly. I … read more I have a 2016 prostar International 9400 truck,with a cummins ISX engine.

The vehicle will not be able to turn over because the electrical wiring in the electric switch isn’t able to communicate with the battery, and the vehicle’s accessories will function poorly (lights dim or not working). Problems in the vehicle’s lock cylinder will impact the driver’s ability to insert the starter key into the lock housing.

Why does my truck shut off even with the ignition Unplugged?

So that pretty much eliminates everything from key switch to ignition relay and to ignition side lug. With all your fuses still having power going to them, that makes me think that the pdm ( fuse panel ) is shorted internally. If you only had power going to one of thoses fuses with all those fuses unplugged, problem would be in that circuit.

Why is my Honda ignition key not turning?

This is a very common and known issue with Honda. Your key is not the issue, it is the wafers in the ignition. The wafers have small points on them which ride along the grooves of the key. When these points become worn, the wafers fall off of the key causing the issue you are describing. Good news. You do not need to replace your ignition.

What happens if there is no ignition switch?

Without the key, the switch won’t move to the start or run positions, and will lock the steering wheel and gear selector. Of course, many cars made in the last 10 years or so have a push button instead of an ignition key and switch. With this design, the key fob sends a signal to the car’s computer saying it’s OK to start the vehicle.

Why does my car key not turn in?

A very common reason a car key won’t turn in the ignition is that the keyway of the ignition cylinder is a little jammed up. Just lubricating the lock may be enough to solve your issue.

Why does my car run when the ignition is turned off?

With the ignition turned off and the car continuing to run, simply remove the plug from the alternator (DO NOT TRY AND REMOVE THE BATTERY POWER WIRE FROM THE POWER STUD!) and the car should shut off if the alternator is creating the problem. If it does not stop running, your feedback problem is coming from something other that the alternator.

When do I Turn Off the ignition key the radio and?

An expert that has 1 follower. Re: When I turn off the ignition key the radio and… On a warn lock cylinder the key may come out even in accessory position so make sure by turning it all the way counterclockwise all the way and then go forward one click clockwise that should be off

Why do I keep the ignition contact closed when I turn the key off?

The explanation is that as you turn the key to start, you first close the contacts to power the ignition, then a bit farther you engage the starter contact (along with the ignition contact). So backing the key off slightly you open the contacts to the starter, yet you are still keeping the ignition contact closed.

What to do if your car dies at a stop light?

Finding the cause of the problem takes experienced troubleshooting skills and a working knowledge of your vehicle’s air, fuel, and electrical systems. Here are some things we look at during our troubleshooting process: Check engine light on?

What happens if you turn off the engine without the key?

Caddiac Thanks..Yeah the engine is still running without the key in it and it either shut off after 5 to 15 seconds or more or it slowly starts to shake till it dies out on its own.

What to do if your ignition cylinder is worn out?

How To Fix It: Fortunately, this is an easy fix. Just turn the wheel back and forth until the ignition cylinder is freed. It’s a fact of life that mechanical things tend to wear out, and the same goes for mechanical keys and key cylinders used in your car’s ignition system.

How To Fix It: After ensuring the rest of the electrical system is intact, such as fuses, relays, and circuits, replace the ignition switch. The transponder antenna surrounds the ignition cylinder. If it doesn’t recognize the transponder key, it doesn’t allow the engine to run. https://www.gettyimages.com/license/525320791

The ignition cylinder is mechanically connected to the steering wheel lock, so a potential thief cannot steer the car without the key. If you turn off the engine with the steering wheel turned or turn the steering wheel after turning off the engine, the steering wheel lock can bind and prevent you from turning the ignition.

How often should you insert and remove the ignition key?

You may insert and remove the ignition key thousands of times every year, wearing the key and tumblers ever-so-slightly every time. Heavy keychains can add more stress to the ignition cylinder, increasing wear. After a while, the key may fall out of the cylinder or be unable to turn out of the lock position.

How To Fix It: Fortunately, this is an easy fix. Just turn the wheel back and forth until the ignition cylinder is freed. It’s a fact of life that mechanical things tend to wear out, and the same goes for mechanical keys and key cylinders used in your car’s ignition system.

A very common reason a car key won’t turn in the ignition is that the keyway of the ignition cylinder is a little jammed up. Just lubricating the lock may be enough to solve your issue.

What to do if your ignition switch is not working?

If the switch is not working, you will likely have to remove and replace it. You can do this with a set of simple tools like a screwdriver. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder.

Can a bad key cause a Mercedes to not start?

Bad Key – If your Mercedes Smart Key IR board goes bad, the EIS (Electronic Ignition Switch) would not recognize the key and this would not give the proper authorizations to the rest of the system to allow the vehicle to start. At Auto Key Pro, we have the tools and expertise to test the key to confirm if that’s the cause of the problem or not.

What causes the key not to turn in the ignition?

5 Reasons Your Ignition Key Won’t Turn Bent or Worn Key. This is perhaps the most common cause of the key getting stuck or not turning. Locked Steering Wheel. The steering system has a locking mechanism which is activated whenever you take the key out of the ignition. Jammed Ignition Cylinder. Gear Not Properly Set. Bad Battery.

Can not get key out of ignition?

  • otherwise the key could break off in the ignition.
  • Jack up the front of the car until the wheels just leave the ground.
  • Spray some Teflon dry lube into the ignition switch around the key.
  • Fill a zip-type sandwich bag half full with ice.

    Why is my key stuck in ignition?

    7 Reasons a Car Key Gets Stuck in the Ignition Parking Gear Not Set. The gear of the transmission must always be set to “Park” before attempting to remove a car key from the ignition. Steering Wheel Lock. If you turn off your vehicle while moving the steering wheel just a little bit, the steering wheel lock will activate. Debris on Key. Dead Battery. Worn or Damaged Key. Damaged Ignition Cylinder.

    How do you remove key stuck in ignition?

    Use pliers to pull out the car keys from the ignition if you can see the broken part. If the broken key inside the ignition is not visible, then take a superglue and stick the key head to the stuck part, hold it for a few minutes and then just yank it from there.

    Is the ignition off but some things stay on?

    The problem that I’m having is a little frustrating. The ignition stays powered up after you pull the key out. It does it almost all of the time. The diesel engine will shut down with no problem, but the GPS, blower fan, wipers and, at times, the cruise control will not function. And “yes” to the answer to your question.

    Can a car still start when the ignition is out?

    Yes, ignition SWITCH. In the interim, when you notice the car still running, try just wiggling the key to see if it moves the switch enough to shut off. Plan now to replace the switch. Most customers in the shop do not realize that the KEY CYLINDER is not the ignition SWITCH.

    Why do things stay on when the ignition switch is off?

    Help would be appreciated. Two things can cause items powered by the key in the ON position to stay on with the key off. 1. First suspect is the IGNITION SOLENOID. Find it. It is “turned on/off” by receiving 12 VDC positive from the ignition switch.

    Yes, ignition SWITCH. In the interim, when you notice the car still running, try just wiggling the key to see if it moves the switch enough to shut off. Plan now to replace the switch. Most customers in the shop do not realize that the KEY CYLINDER is not the ignition SWITCH.

    What happens if you have an ignition switch problem?

    However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems. To be sure, ignition switch problems are no fun, especially if they’re stopping you from getting to work or school or play.

    What to do if your ignition switch is bad?

    Bad Ignition Switch: If your battery checks out, but the starter is still silent, it might be a faulty ignition switch. Turn the key to the “On” position, not all the way to start, and check the following: If the red warning lights on your dash don’t light up and your battery connections are clean, the ignition switch is bad.

    What does it mean when your car won’t start when you turn the key?

    If you hear a clicking sound, this often means the electrical components are not working. However, if there is no sound at all, and especially if you see the dashboard lights or dials come on when you turn the key, this often means the engine simply won’t even try to start since it’s not getting that needed signal from the key.

    Where do I put the key to start my car?

    Some push-button ignition systems may also have a place to insert the physical key and allow you to start the vehicle, generally between the steering wheel and the infotainment system. These quick fixes can occasionally work in a pinch and allow you to get back home or go to AutoZone to buy a replacement battery or key fob.

    Why do I need a transponder key to start my car?

    A transponder key has a small computer chip inside that communicates with your car’s engine, and this type of key is almost always standard for cars today. Transponder keys must be used to start the car’s engine; if the car’s engine doesn’t get a signal from the key, its immobiliser keeps it from starting by any other means.

    Why does my car starter lock up when I turn the key?

    Another possibility is that the solenoid isn’t supplying power to the starter motor. The plunger may not be retracting all the way to make contact or the contact surfaces might be corroded. Buy ($15) or borrow a DVM and measure the voltage to the solenoid and then at the starter motor when the key is turned to START.

    What to do if your car key won’t start?

    However, before you assume that there is a problem with the car’s engine or even the starter, you might consider that the key you use to start your car could be at fault.

    Can a starter lock up solid without pulling the starter off?

    I’ve even seen this a few times with connecting rods sticking through the block of all things. If the engine isn’t seized, the starter Bendix gear may be stuck in the flywheel. If there is an inspection plate on the engine block you may be able to see if this is the problem without pulling the starter off.

    Can a push start Car start with a key?

    Q: Won’t start with the key, but I can lock and unlock the doors. My BMW is a push start and the dash says it still needs the key to be able to start the car even thought the key is in the ignition, I can still unlock and lock the car just fine.

    Bent keys can sometimes enter the ignition cylinder, but once inside will not line up correctly to allow the car to start. If your key looks visually bent, you can use a non-metal hammer to carefully flatten the key down. Your goal is to use something that will not damage the key, so ideally this would be made of rubber or wood.

    Why is my key not turning in ignition?

    The three main reasons why an ignition key will not turn include: problems with related components, issues with the key itself, and ignition lock cylinder problems. Tip: Always make sure your parking brake is on to keep the vehicle secure when following these steps.

    Can’t Put key in ignition?

    As dirt is the major reason for the key not getting into the ignition , chances are that a few fragments might have stuck to the pins of ignition cylinder. Insert the key into the port as much you can and softly slide it back out. Go through the entire process numerous times until the key gets into the port completely.

    Why will my car key not turn?

    The most common reason that a car key will not turn is that the steering wheel has locked. This will happen when the steering wheel has been moved after the key has been removed from the ignition cylinder. Turn the steering wheel to the right and left.

    Why is my car stuck in ignition?

    7 Reasons a Car Key Gets Stuck in the Ignition #1 – Parking Gear Not Set #2 – Steering Wheel Lock #3 – Debris on Key #4 – Dead Battery #5 – Worn or Damaged Key #6 – Damaged Ignition Cylinder #7 – Manufacturer Recall or TSB

    Why can’t you turn key in the ignition?

    If your key won’t turn when you insert it into the ignition, it may be because the key has been damaged and no longer engages the correct pins to the depth necessary to spin the cylinder. Examine the key for signs of excessive wear, rounding or broken teeth. Any of these could result in the key failing to turn in the ignition.

    Can’t Insert key into ignition?

    When does the ignition warning light not come on?

    If your car is fitted with an alternator the warning light should not come on when the engine is idling, provided the idle setting is correct, because an alternator produces current even at low speeds.

    What are common reasons my Dodge Dakota key wont turn?

    What are common reasons my Dodge Dakota key won’t turn? While there are a variety of reasons your Dodge Dakota key won’t turn, the most common 3 are a binding steering column/lock, an ignition switch issue, or a problem with the ignition key.

    Why does my car key not turn in the ignition?

    A very common reason a car key won’t turn in the ignition is that the keyway of the ignition cylinder is a little jammed up. Just lubricating the lock may be enough to solve your issue. You will say that WD40 is often the go-to example for lubrication of any kind, but I would not recommend it in this case.

    If your car is fitted with an alternator the warning light should not come on when the engine is idling, provided the idle setting is correct, because an alternator produces current even at low speeds.

    So that pretty much eliminates everything from key switch to ignition relay and to ignition side lug. With all your fuses still having power going to them, that makes me think that the pdm ( fuse panel ) is shorted internally. If you only had power going to one of thoses fuses with all those fuses unplugged, problem would be in that circuit.

    Won’t shut off with key. Data says key is in run position when key is off. Already verified the key switch is working correctly. I … read more I have a 2016 prostar International 9400 truck,with a cummins ISX engine.

    The ignition in my 98 has been acting weird for some time. I can pull the key from the ignition while the truck is running. If you are not careful, you can turn the engine off without putting the key in the off position. The key will come out in the accessory position and you can turn the ignition with no key and start the truck.

    How do you get a stuck ignition out of a Ford?

    Now use a small screwdriver, pick tool, or other implement to release the catch on the cylinder body. Insert it into the hole as illustrated, and pull on the handle of the key – the cylinder should slide right out.

    What makes a Ford ignition not turn on?

    On the inner lock cylinder, you will see a flat bar that sticks out, and about 90 degrees around, a thin piece of sheet metal covering the tumblers. The bar is what keeps the inner cylinder from rotating until the key has been inserted.

    Do you have to have Pats for Ford ignition?

    Ford has a passive anti-theft system (PATS) where each key has a chip, and they have to be programmed in. No problem if you’ve got two functional keys, because you can add new ones, but you have to be able to turn the key in the ignition to do so.

    Now use a small screwdriver, pick tool, or other implement to release the catch on the cylinder body. Insert it into the hole as illustrated, and pull on the handle of the key – the cylinder should slide right out.

    On the inner lock cylinder, you will see a flat bar that sticks out, and about 90 degrees around, a thin piece of sheet metal covering the tumblers. The bar is what keeps the inner cylinder from rotating until the key has been inserted.

    Ford has a passive anti-theft system (PATS) where each key has a chip, and they have to be programmed in. No problem if you’ve got two functional keys, because you can add new ones, but you have to be able to turn the key in the ignition to do so.

    Why does my Peugeot key stop going into the lock?

    Then the key stops going into the lock at all. This is very common on door locks of Peugeot Partners, 107’s and 407’s and alot of the Citroen range. Before you spend any money, it’s important that you are sure that the key is faulty.

    What to do if your Peugeot car key wobbles?

    Fixing a Peugeot key blade that wobbles. We’re often asked if we sell the springs that go into the keys, or just the blade part. Unfortunately, because of how the key is manufactured, a completely new case is needed. This is a simple job once you’ve found the correct case, and there are over twenty varieties!

    What’s the flip key on a Peugeot car?

    To come in line with VW etc, they designed a flip key. Quite frankly ‘designed’ is the wrong word, because whoever in the office signed this off surely hadn’t even looked inside it. The blade assembly is cheaply made, with just a thin slither of plastic keeping everything in place and working.

    Why is my key not turning in my Peugeot?

    If the key is stopping slightly short when inserted into the barrel, the problem will no doubt be caused by the anti pick bar not fully returning to the correct position. The do it yourself solution:

    Why does my steering wheel not turn when I turn the key?

    Turn the Steering Wheel The most common reason that a car key will not turn is that the steering wheel has locked. This will happen when the steering wheel has been moved after the key has been removed from the ignition cylinder. Turn the steering wheel to the right and left.

    How can you tell if your ignition key is locked?

    Check to see if your steering wheel is locked by trying to turn the wheel. If it will not move, or moves only very slightly, it is likely locked. A locked steering wheel will not allow the ignition to engage. When you move the wheel back and forth, you will feel it stop abruptly as it comes into contact with the steering wheel lock.

    Can a Mercedes W210 pull the ignition key out?

    Well, first off, the brake has zero to do with pulling a key out on a W210 (at least on MY2000). Started, turned off, tons of times without sitting in the seat with foot on brake. I will also keep an eye on the shifter being fully in park and wheel position. From what I understand, there is no shifter adjustment, so who knows.

    What to do when your car won’t start?

    If this does not work, rock the steering wheel as you jiggle the key in the ignition. You can mix and match with the methods of turning the wheel and moving the key. As soon as the key turns the steering wheel will unlock, and the car should start. If the key does not turn, then you may have a more severe issue.

    Why does the key not turn in the ignition?

    The problem is that if the wheels are turned all the way in one direction, or if the wheels are butted up against something (like a curb), then it can be very difficult to release the locking mechanism, even with the key is in the ignition. The usual solution to this is to wiggle the steering wheel while trying to turn the key.

    What to do when your car key won’t turn in?

    You can use WD40 as long as you are going to be changing out the ignition cylinder after you turn the key successfully. When you are going to replace it anyway, it gunking up further over time does not matter. Gather your lubricant, key, and cloth. Spray the lubricant into the keyway of the ignition cylinder.

    Why does my Honda Accord key not turn?

    The ignition switch on my 2004 Honda Accord developed a problem. The key simply woul not turn in the ignition! I was finally able to get it to turn one day after I jammed one of the keys in to the ignition to get it to turn. But unfortunately, after that, the key would not turn in the ignition!

    What happens when the ignition switch is off?

    Generally speaking, in the “OFF” position, the ignition switch doesn’t connect anything; in the “ACC” position, the radio or fan may be energized; in the “RUN” position, the engine control module is energized; and finally, in the “START” position, the starter relay is engaged. (These generalizations, depend significantly on year, make, and model.)

    Why does my engine not stop when the ignition switch is turned off?

    The dealer said it was the spark plug wire that was running directly over the distributor cap and arching, which caused the plugs to continue to fire. The new spark plugs didn’t help, still doing it. The dealer is going to troubleshoot it again but now they are talking about replacing the ECM, which is estimated to be around $1500.

    What happens when the Kill Switch is off on a boat?

    – Kill switch doesn’t stop the engine either – but it does prevent the boat from starting when Kill switch is off. Dealer looked at the issue last year and couldn’t get it to repeat. I replaced the ignition switch and it seem to work but the problem came back.

    What’s the best way to remove a car key?

    Step 1: Lubricate the lock. Spray some lock lubricant into the lock cylinder. Step 2: Slide the blade into the lock. Take your hand jigsaw blade and carefully slide it into the lock cylinder. Step 3: Pull the blade out of the lock. When the hand jigsaw blade stops sliding, you’ve reached the end of the lock cylinder.

    Why does my key not turn when I turn the car off?

    When you move the wheel back and forth, you will feel it stop abruptly as it comes into contact with the steering wheel lock. If your wheel was turned slightly without you applying any pressure when you turned the car off, it still may engage the steering wheel lock.

    How do you get the ignition key out of a Subaru?

    If that doesn’t help, time to call the dealer. First the issue in getting the key out. Not sure of the XV’s but previous Subaru’s had a small hole below the ignition in the lower steering wheel cover. By placing a small screwdriver or similar device in the hole and pressing caused a release to be activated allowing you to remove the key.

    Step 1 – All vehicles have a steering wheel lockout safety device that will not allow the steering wheel to turn when the key is in the “OFF” position. Step 2 – Vehicles equipped with power steering utilize a pump which maintains pressure while the engine is running.

    Why are my car keys stuck in ignition?

    What is ignition lock key?

    The ignition lock cylinder is the cylindrical tumbler and key that is used to power on and start the vehicle. While many newer vehicles are now being manufactured with push button and keyless power and starting systems, traditional ignition lock cylinders are still commonly found on many road going cars and trucks.

    What is an ignition lock position?

    The ignition lock is where you insert the key to start the car and locks the steering wheel until the key is inserted and turned to the “on” position. The steering wheel cannot be rotated without the key in the “on” position, which means a thief cannot drive off with the car just by hot-wiring it.

    How do you remove a ring from an ignition?

    Reach back behind the ignition under the dash, you will feel a ring. Turn the ring with a pair of pliers or a wrench until the ring is completely loose. Remove the wires connected to the back of the ignition, then pull the ignition forward through the hole.

    What should I do if my ignition switch is going bad?

    If the key still won’t come out, the problem may a damaged column locking mechanism. On the other hand, if the switch is going bad, the engine may keep running after you remove the key. The easiest and safest way to replace an ignition switch is to; take your vehicle to a repair shop or new car dealer and have them replace your ignition switch.

    What should I do if my ignition key is broken?

    Clear away any obstructions in the ignition lock. Remove any debris from that might be blocking the key fragment with compressed air. Do not spray cleaners or lubricants into the ignition lock as these chemicals may damage the lock. This is especially true for newer vehicles with added features. Place the place entire key back into the lock.

    How can I remove the ignition chime from my car?

    To remove this you will also be losing the ignition chime when the keys are in the ignition or when the doors open. It can be removed simply by unplugging it. Just open the door with the keys in the ignition, look under the dash on the driver or passenger side. using you good hearing locate the chime and simply disconnect the plug from the back.

    Why does my car stop when I press the stop button?

    On vehicles equipped with the Start/Stop convenience feature, the engine may not stop when you press the STOP button. A defective Push Start button can cause this problem. If the button stops working, it may need to be replaced.

    Can a bad ignition switch cause a fire?

    Bad ignition switches have been known to cause fires, so get this taken care of quickly. Yes, ignition SWITCH. In the interim, when you notice the car still running, try just wiggling the key to see if it moves the switch enough to shut off. Plan now to replace the switch.

    What causes an engine to run with the key off?

    • A leak on the IP BEC could cause various electrical concerns such as: Engine Continues to Run with Key Off/Possible No Crank/No Start/Communication Loss/Various Electrical Concerns. • This leak may also cause some communication issues between certain electrical modules due to water dripping on the IP BEC.

    Why does my Ford starter keep running even after I Turn Off the engine?

    Some Ford owners encounter a situation where the starter run continuously or keeps running even after the engine has started and even after they’ve removed the key from the ignition. At first, this may make you think the starter drive is binding. Or you may think you have a bad starter relay.

    Why does my car not stop when I Turn Off the ignition?

    It turns out that the engine was not being turned off by removing the power from the Ignition Relay, it was actually being starved of fuel by the Anti Run-On Valve. Since the British models did not have the Anti Run-On Valve, the engines would not stop, but instead kept on running even when the Ignition Key was removed. What was happening?

    Do you need to replace the ignition switch?

    It may happen that your car’s engine operates correctly after the ignition switch is detached. If so, you require locating the power relay for the ignition and fuel system. Remove the main relay and check if your car finally shuts down. In case it powers down, you need to replace the main relay.

    When do you turn off the ignition on a MG?

    Back in the mid 70’s when the US introduced emission standards, MG made some modifications to the US models. One of these modifications was the Anti Run-On Valve another was the Ignition Relay. The idea was that to turn off the engine, you removed the ignition by removing power from the Ignition Relay. This was applied to US ‘77 and ‘78 models.

    What can cause an ignition switch to fail?

    (These generalizations, depend significantly on year, make, and model.) Worn ignition switch contacts, temperature problems, or broken springs can all cause the ignition switch to fail, preventing you from starting your car. On the road, poor ignition switch contacts could shut the engine off while driving, which could be dangerous.

    How is the ignition switch connected to the car?

    The ignition switch itself is connected to the ignition cylinder by a shaft or lever. Inside the ignition switch, several contacts connect vital electrical systems needed to start and run the car.

    Can you use a tool to turn the ignition?

    Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key. Use the correct key, make sure it is all the way in, and turn it only with your hand. If the key cannot be turned by hand, see your dealer. The key must be fully extended to start the vehicle.

    What to do when your ignition key is out?

    In the interim, when you notice the car still running, try just wiggling the key to see if it moves the switch enough to shut off. Plan now to replace the switch. Most customers in the shop do not realize that the KEY CYLINDER is not the ignition SWITCH.

    Why does a car starter spin after the key is taken out?

    Why would a starter still spin after the ignition switch is turned off and the key is taken out. My 79 trans am just developed this problem. It’s only a 2 year old rebuilt starter. Today, while up in the mountains, in the middle of nowhere, I shut the car off to let my dog outside for a bit.

    Why is my ignition key stuck in my car?

    The cause ‘could’ be a faulty neutral switch. Yes even though you can’t remove the ignition key from anywhere else but Park, it also acts as an interlock. If the ignition is not getting a signal that the transmission is not in Park, it won’t release the key. Intermittent tries as you have performed indicate it is ‘intermittently’ working.

    What happens to the engine when you turn the key?

    Turning the engine causes the pistons to rise and fall in the engine block, activates fuel and spark, and (hopefully) ignition of the engine so that it begins running on its own without the starter motor turning it.

    Why does my car not start when I turn the key?

    If the engine does not crank, then you may have a starter problem. If the engine does not crank, and the security / theft warning light stays on when it won’t start- and you let go of the key to the ON position, then this is most likely a problem in the Passlock system. The ignition cylinder is also know as the Passlock Sensor.

    Turning the engine causes the pistons to rise and fall in the engine block, activates fuel and spark, and (hopefully) ignition of the engine so that it begins running on its own without the starter motor turning it.

    Why do I turn the ignition on and off so many times?

    Other times I just turn the ignition on and off about 5 or 6 times and it starts. I can detect a pattern to this problem as it seems to come and go. vehicle. If the engine does not crank, then you may have a starter problem. If the engine does not crank, and position, then this is most likely a problem in the Passlock system.

    How to unlock and start Ford Fusion with dead key fob?

    How to unlock and start Ford Fusion with dead key fob battery! If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

    How much does a Ford Fusion general diagnosis cost?

    The average cost for a Ford Fusion General Diagnosis is between $88 -$111. Learn More I have a 2011 Ford fusion. Key stuck in the ignition. Unlike the 2006 model, there isn’t a ring on the shifter to release my key.

    How to unlock and start Ford Fusion with dead key fob battery! If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

    What causes a car key to not come out of ignition?

    If the key will not come out of ignition, this may be related to problems with the shifter knob sticking and / or binding of the shifter bezel. Replace the shifter knob and / or shifter bezel as needed.

    The average cost for a Ford Fusion General Diagnosis is between $88 -$111. Learn More I have a 2011 Ford fusion. Key stuck in the ignition. Unlike the 2006 model, there isn’t a ring on the shifter to release my key.

    Why does my tractor not start when I turn the key?

    I originally thought the problem was being caused by accidentally putting my foot either on the forward or reverse pedal when turning the key to start …..which assume if that happens the tractor would not start due to safety feature (OPC safety device?).

    How does the torque of a key grow?

    In other words, the torque grows linearly with the angle with which you turn the key. In that case, you simply need to find the minimum torque required to balance the key in an unlocked position, without breaking the key or the lock.

    You can use WD40 as long as you are going to be changing out the ignition cylinder after you turn the key successfully. When you are going to replace it anyway, it gunking up further over time does not matter. Gather your lubricant, key, and cloth. Spray the lubricant into the keyway of the ignition cylinder.

    What does it mean when my key will not turn in my ignition?

    Inspect the key for damage. If your key won’t turn when you insert it into the ignition, it may be because the key has been damaged and no longer engages the correct pins to the depth necessary to spin the cylinder. Examine the key for signs of excessive wear, rounding or broken teeth.

    What to do when the ignition key won’t turn?

    • Method 1 of 3: Checking for Common Issues. Ensure the vehicle is in park.
    • Method 2 of 3: Resolving Issues with the Key. Pull the key out slightly before turning it.
    • Method 3 of 3: Addressing Issues with the Ignition Cylinder. Use canned air to clean the ignition port.

      How do I clear MyKey on my Ford Focus?

      On the main menu, select “Settings” by pressing “OK.” Under “Settings,” scroll to the option that says “MyKey,” then press “OK.” Under “MyKey,” search for the option that says “Clear MyKey.” With this setting selected, press and hold “OK” until the message “All MyKeys Cleared” appears on screen. What is Ford MyKey?

      Is there way to get it to turn off with ignition?

      When i’m running a usb phone charger from the cigarette lighter it stays on after the ignition is turned off. c’ve nearly been caught out a couple of times and am going to run out of luck before too long and come back to a flat battery. Is there a way to get it to switch on and off with the ignition? Car is 2008 mk 2.5. Thanks in advance.

      How can I get my keys out of my car?

      If not you will need to see if you can rotate the cylinder to the run position, then push the release in with a punch to pull out the entire cylinder. Next is to carefully pull out on the trim cover above the column, This can be tricky as the plastic tends to get brittle. With that cover off remove the upper steering column cover.

      Why does the Radio shut off when the key is taken out of ignition?

      there is a push pin in the ignition when the key is taken out the pin closes and radio etc goes off. spray some wd40 in the ignition and pushe key in and out a few times should free it up. Radio on chrysler 300 won’t shut off when key is turned off. When i open the door the radio shuts off. This is actually normal.

      Can you use a non Pats key on a Ford Expedition?

      If you use a non PATS key, such as one that was cut simply to open the doors from an all-metal key blank, the system will remain armed. If the Expedition starts, then you have disarmed the PATS system. If not, move on to step 2. Verify you have the right key. Ford PATS keys have large black plastic, or molded rubber, heads.

      Is there a factory alarm on a Ford Expedition?

      While some erroneously call this system the factory alarm, it really is not an alarm system. The PATS system will arm itself if someone attempts to start the vehicle with anything other than the PATS key programmed to that specific vehicle.

      How to troubleshoot the theft protection in a Ford Expedition?

      Moore is a contributing writer for RF365.com and various other websites, a ghostwriter for Rainbow Writing and has over a dozen works of fiction currently in print. How to Troubleshoot the Ford Securilock

      What is the halo on a Ford Expedition?

      The halo is a small ring that rests around the ignition tumbler in order to recognize the proper key. If you have had your ignition tumbler or switch replaced recently, and are now having PATS troubles, inspect the halo for damage. It can be broken easily if care is not exercised when removing or reinstalling the ignition tumbler.

      Why do the dash lights stay on when you turn off the ignition?

      When they turn off the ignition of the car and remove the key, somehow the dashboard lights are still on. It has left many car owners wondering about what could cause this issue. Car experts recommend that if the lights are on even when the key to the ignition is taken out, the majority of times it is an issue with the ignition switch.

      Why does my car not turn off when I Turn Off the engine?

      Dieseling is rarely a problem with fuel injection because the fuel delivery is shut down as soon as the switch is off. Unless it is specially equipped, a carburetor will deliver fuel as long as there is air passing through it. If you have a fuel injected car that is dieseling, there is a leaking fuel injector in the system that has to be replaced.

      Where is the ignition switch on a car?

      Remove the bottom half of the plastic shroud surrounding the steering column. Locate the electrical connector to the ignition switch. It may be on the back of the ignition switch itself, or it might be at the end of an electrical pigtail from the switch and be located further down the steering column.

      Why is my car dieseling after I shut it off?

      If you have a fuel injected car that is dieseling, there is a leaking fuel injector in the system that has to be replaced. Step 2: Check the idle speed. If the engine idle speed is too high, it may cause the car to diesel after it is shut off. Hook up your tachometer according to instructions and check the idle speed.

      What should I do if my key won’t turn?

      The ignition switch needs to have the small linkage from the back side of the key lock cylinder to turn the switch to start and run the vehicle. Have the ignition switch removed and inspect the linkage and switch to see if one or both switch and linkage needs replaced.

      Why does my car key not turn when I take the key out?

      That is why it won’t turn. The steering system has a locking mechanism which is activated whenever you take the key out of the ignition. Sometimes, you might inadvertently move the steering wheel as you take the key out of the ignition.

      Why is the ignition switch on my car not working?

      My car has an automatic transmission. The ignition switch or linkage to the switch is broken. The ignition switch needs to have the small linkage from the back side of the key lock cylinder to turn the switch to start and run the vehicle.

      Can a car key come out if the car is in Park?

      The gear of the transmission must always be set to “Park” before attempting to remove a car key from the ignition. In an automatic transmission, if the gear is set to drive, neutral, or any other available gear, then the key will not come out.

      What happens if your car does not shift into Park?

      If your vehicle does not shift into park, you will not be able to get the key out of the ignition. This is a safety feature on all cars so that if the vehicle is still in motion, the battery and engine can be safely operated. If the car cannot be shifted into park, you will need to have repairs made to the shifter belt.

      What happens if you can’t get the key out of the ignition?

      Warning. If the cable is too damaged to be shifted into park by using the above steps or the transmission is badly damaged, the car may need to be towed or driven to a local repair shop. Since you will not be able to get the key out of the ignition because it won’t shift into park, a repair shop will be able to safely disengage…

      The gear of the transmission must always be set to “Park” before attempting to remove a car key from the ignition. In an automatic transmission, if the gear is set to drive, neutral, or any other available gear, then the key will not come out.

      Can a Honda Civic key get stuck in the ignition?

      A key getting stuck in your Civic’s ignition is not the most common problem. You can go the whole life of the vehicle and this typically won’t happen. Here are some of the most common reasons why the key would get stuck in the ignition. They are presented somewhat in the order of most likely to least likely to be the cause.

      What does it mean when the key won’t come out?

      What I mean is you can change the gears without pushing the button on the side of the gear shifter so I didn’t know if this may be the problem since the key won’t cut off or come out if the car is not in park. My car has 999999 miles. My car has an automatic transmission. It is either the ignition switch electrical or the ignition lock cylinder.

      Why does my GM ignition key not turn?

      Sometimes the ignition key won’t turn or rotate. If that happens the vehicle won’t start, the steering wheel won’t turn and it won’t shift into gear. On a late 90’s or early 2000 GM vehicle this is the way to get it apart so you can replace the tumbler. Category Autos & Vehicles.

      What I mean is you can change the gears without pushing the button on the side of the gear shifter so I didn’t know if this may be the problem since the key won’t cut off or come out if the car is not in park. My car has 999999 miles. My car has an automatic transmission. It is either the ignition switch electrical or the ignition lock cylinder.

      What to do if your car key is stuck in the ignition?

      At that point a replacement part can be ordered and the appropriate repair can be done. In order to avoid any unnecessary repairs, consider getting the car’s no start condition inspected by a certified mobile technician, such as one from YourMechanic. Good luck!

      What happens if you break the ignition lock?

      The key slides into the ignition lock cylinder. These two components mate together and essentially become one. So if either of them break, they will both be affected. In addition, there are many other small moving parts inside your steering column that are activated when you insert the key and turn it.

      What should I do if my car key won’t come out?

      Any car key in an ignition should easily slide out after you have completely rotated it counterclockwise and (if applicable) pushed the key release button. If the key won’t come out of the ignition, then you need to understand the possible cause of this problem. There are a variety of reasons as to why your car key won’t come out.

      How do you get a bad key out of a car?

      Try gently wiggling the key by hand as you try to pull it out. Apply some WD-40 or graphite between the key and the lock, if you can. If you do get the bad key out, try using your spare ignition key, which should be in newer, better condition.

Author Image
Ruth Doyle