What does the p0102 Ford MAF sensor mean?

P0102 FORD Meaning The Mass Air Flow (MAF) sensor is placed in the stream of intake air. It measures the intake flow rate by measuring a part of the entire intake flow. It consists of a hot film that is supplied with electric current from the Engine Control Module (ECM).

How long does it take to fix Ford p0102 code?

Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor. The cost of diagnosing the P0102 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

Is the Ford mass air flow ( MAF ) sensor inside?

Ford has used a Hot-Wire type mass air flow sensor for many years that either comes with or without an internal air temperature sensor. If the MAF sensor has 6 wires, then this is a dead giveaway that it has the air temp sensor integrated inside.

What are the codes for mass air flow?

Note: Some MAF sensors also incorporate an air temperature sensor, which is another value used by the PCM for optimal engine operation. Closely related MAF circuit trouble codes include P0100, P0101, P0103, and P0104. Photo of a MAF sensor:

What does code p0102 mean on the ECM?

Mass or Circuit Airflow (MAF) Circuit Low Voltage Input What Does P0102 Mean? The Mass Airflow (MAF) sensor measures the amount of air entering the engine. When code P0102 is set, there is a low voltage output to the ECM, PCM, or ECU depending on your car type (check your owner’s manual for your specific car).

What causes a faulty mass air flow sensor?

Possible causes. Faulty mass air flow sensor. Intake air leaks. Dirty mass air flow sensor. Dirty mass air filter. Mass air flow sensor harness is open or shorted. Mass air flow sensor circuit poor electrical connection.

What should I do if my Ford p0104 code comes back?

Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor. The cost to diagnose the P0104 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What does code p0172 and p0175 mean?

Both codes mean, in layman’s terms, that the PCM (Powertrain Control Module= Fuel Injection Computer) is reducing the amount of fuel that it’s injecting into the engine and that it can no longer fine-tune the air/fuel mixture. This reduction in fuel is carried to an extreme because ‘something’ is causing the air/fuel mixture to be to fuel heavy.

What are the diagnostic codes for Ford 4.6L?

I’ll also offer you a testing strategy to find the root cause of them. Although you can apply this info to any Ford vehicle with a V6 or V8, this info concentrates on the Ford 4.6L and 5.4L V8 engines. TIP 1: A scan tool with Live Data capability is a must, to test diagnostic trouble codes P0172 and P0175.

What should I do if my Ford p0102 code comes back?

Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor. The cost to diagnose the P0102 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What does the p0104 Ford MAF sensor mean?

P0104 FORD Meaning The Mass Air Flow (MAF) sensor is placed in the stream of intake air. It measures the intake flow rate by measuring a part of the entire intake flow. It consists of a hot film that is supplied with electric current from the Engine Control Module (ECM).

What is the OBDII code for a Ford?

OBDII Code List P0102 FORD P0102 FORD – Mass or Volume Air Flow Circuit Low Input Repair Importance Level: 3/3 Repair Difficulty Level: 2/3 Comments | Add Comment P0102 FORD Possible Causes Faulty mass air flow sensor Intake air leaks Dirty mass air flow sensor Dirty mass air filter Mass air flow sensor harness is open or shorted

What does the p0113 code on a Ford mean?

P0113 Ford Meaning. The Intake Air Temperature (IAT) sensor is built into mass air flow sensor or in some vehicles mounted to the air filter duct housing. The sensor detects intake air temperature and transmits a signal to the Engine Control Module (ECM).The temperature sensing unit uses a thermistor which is sensitive to the change in temperature.

What is the problem code on a Ford F150?

P0113 Ford F150. P0113 is an OBDII trouble code that occurs when the Ford F150′s engine management computer detects that there is an issue with the Intake Air Temperature (IAT) Sensor, specifically that there is a High Input Problem with it.

Are there air leaks in the Ford MAF sensor?

The second most common problem I have encountered on most Fords (Mercurys and Lincolns) over the years is air leaks between the MAF sensor and the throttle body. It is crucial, yes very critical that you first check that there are no air leaks between these two.

What do you need to know about Ford code p0113?

Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded terminals. The cost of diagnosing the P0113 FORD code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type.

What does p061c mean in Powertrain Control Module?

When a code P061C is stored, it means that the powertrain control module (PCM) has detected an internal performance error in the engine RPM (revolutions per minute) monitoring system. Other controllers may also detect an internal PCM performance error (with the engine RPM monitoring system) and contribute to a P061C being stored.

What are the symptoms of a p0102 low OBD code?

Symptoms of a P0102 code may include: 1 Malfunction indicator lamp (MIL) illumination (a.k.a. check engine light). 2 Rough running engine. 3 Black smoke from tail pipe. 4 Stalling. 5 Engine hard start or stalling after it starts. 6 (more items)

Why does my car have a low air flow code?

The air filter may be very dirty causing the sensor to show low air flow voltage due to air flow restriction. How serious is the P0102 code? The P0102 code will generally not prevent the car from driving.

When do I need to fix trouble code p0102?

A trouble code P0102 is triggered when there is low airflow registered by the Mass Air Flow, or MAF, sensor. When this happens, you need to know how do I fix trouble code P0102?

What is the trouble code for Ford OBD II?

Ford P0101 OBD-II Trouble Code Definition: P0101 Mass Air Flow Circuit Range/Performance. P0101 Ford OBD-II Trouble CodeDescription: OBD Trouble Code P0101.

What does 103 kPa mean on Ford OBD code?

With the ignition ON and the engine OFF, 103 kPa is the approximate value near sea level. This value will decrease by approximately 3 kPa for every 305 meters (1,000 feet) of altitude. A high resistance on the ground circuit of the MAP sensor can cause this DTC to set. Any loss of vacuum to the MAP sensor can cause this DTC to set.

What does the p0105 code on the MAP sensor mean?

What the P0105 code means. P0105 is the general code for a problem with the MAP circuit having an electrical failure or malfunction. The MAP sensor is an integral part of the fuel injection system and provides signals to the Engine Control Unit (ECU) for smooth operation and good fuel economy.

What is the problem code for the manifold air pressure sensor?

Manifold Air Pressure (MAP) Barometric Pressure Sensor Electrical Circuit Problem P0105 is the general code for a problem with the MAP circuit having an electrical failure or malfunction. The MAP sensor is an integral part of the fuel injection system and provides signals to the Engine Control Unit (ECU) for smooth operation and good fuel economy.

How to test the Ford MAF sensor 4.2L?

You can find this tutorial in Spanish here: Cómo Probar El MAF Ford (4.2L, 4.6L, 5.4L) (at: autotecnico-online.com ). This list covers the majority of symptoms I’ve seen on these types of Ford mass air flow sensors: MAF Codes that light up the check engine light (CEL) on your instrument cluster.

Where is the MAF sensor on a Mercury?

If your Ford or Mercury vehicle uses the MAF sensor in the round Canister Air Filter assembly, go here: Ford MAF In Round Canister Air Filter Assembly. This is not the most definitive list on the subject, but does cover the majority of symptoms I’ve seen on these types of Ford mass air flow sensors:

What to do if your car has a p0101 code?

Check for damaged components and look for broken, bent, pushed out, or corroded terminals. Before replacing the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with low compress air or mass air flow sensor cleaner. Reset code and drive vehicle.

How much does it cost to fix a p0104 Ford?

The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P0104 FORD code detected? The ECM has detected an air flow signal that is outside the calibrated level. The Mass Air Flow ( MAF) sensor is placed in the stream of intake air.

Where is the mass air flow ( MAF ) sensor located?

The Mass Air Flow ( MAF) sensor is placed in the stream of intake air. It measures the intake flow rate by measuring a part of the entire intake flow. It consists of a hot film that is supplied with electric current from the Engine Control Module ( ECM ).

What does the p0102 Ford MAF sensor mean?