What does the p0011 stand for in DTC?

P0011 A camshaft position – timing over advanced or system performance (Bank 1) P0012 A camshaft position – timing over retarded (Bank 1) P0013 B camshaft position – actuator circuit (Bank 1) P0014 B camshaft position – timing over advanced or system performance (Bank 1) P0015 B camshaft position – timing over retarded (Bank 1)

What is the difference between p0010 and p0014?

P0010 A camshaft position actuator circuit (bank 1) P0011 A camshaft position – timing over advanced or system performance (Bank 1) P0012 A camshaft position – timing over retarded (Bank 1) P0013 B camshaft position – actuator circuit (Bank 1) P0014 B camshaft position – timing over advanced or system performance (Bank 1)

What does p1684 mean on a Dodge Ram?

P1684 indicates that the memory has been cleared within the last 50 ignition cycles and does not indicate a problem. Done indicates that NO DTCs are present. Ho2S = heated oxyen sensor, TP = throttle position, MAF = mass airflow, MAP = manifold absolute pressure, TC=turbocharger.

When do you need an OBD2 diagnostic code?

These codes are stored when a sensor in the car reports a reading that is outside the normal/accepted range (Eg: fuel mixture too rich). These DTC’s identify a particular problem area and are intended to provide the technician with a guide as to where a fault might be occurring within the vehicle.

What does code p0122 on a TPS mean?

Throttle Pedal Position Sensor/Switch (TPS) A Circuit Low Input What Does Code P0122 Mean? Code P0122 is triggered when your vehicle’s Engine Control Module (ECM) detects that your Throttle Position Sensor (TPS) circuit A is reporting an output voltage that is below its expected voltage.

What does the code p0122 on the ECM mean?

What Does Code P0122 Mean? Code P0122 is triggered when your vehicle’s Engine Control Module (ECM) detects that your Throttle Position Sensor (TPS) circuit A is reporting an output voltage that is below its expected voltage.

What does p1122 stand for in engine control?

P1122 Meaning Electric Throttle Control Actuator consists of throttle control motor, Throttle Position Sensor (TPS), etc. The throttle control motor is operated by the Engine Control Module (ECM) and it opens and closes the throttle valve.

What are the possible causes of p1811 code?

P1811 Possible Causes 1 Faulty Pressure Control Solenoid 2 Pressure Control Solenoid harness is open or shorted 3 Pressure Control Solenoid circuit poor electrical connection

What are the C codes for trouble codes?

C Codes C Codes Trouble Code Fault Location C0000 – C0999 (Brakes and Traction contr C0000 – C0999 (Brakes and Traction contr C0000 ISO/SAE Reserved C0001 TCS Control Channel “A” Valve 1 (Subfaul

What is the DTC code for a camshaft?

P0013 B camshaft position – actuator circuit (Bank 1) P0014 B camshaft position – timing over advanced or system performance (Bank 1) P0015 B camshaft position – timing over retarded (Bank 1) P0016 – Crankshaft Position Camshaft Position Correlation Bank 1 Sensor A P0020 A camshaft position actuator circuit (Bank 2)

Is it safe to drive with traction control light on?

If the only light illuminated on the dash is the traction control light, chances are it’s fairly safe to drive. If it’s wet or slippery outside, you’ll want to take extra care when accelerating or taking turns. In these conditions, the vehicle may behave unpredictably.

When to use code p0650 in engine control module?

A code P0650 will be stored when the engine control module (ECM) or other supporting control module has detected a fault or malfunction with the control circuit of the malfunction indicator lamp. A vehicle’s malfunction indicator lamp tells the driver when there is a potential problem with the vehicle.

How does the p0650 malfunction indicator lamp control?

If the fault detection circuit senses a voltage other than what is expected, the fault line status will change causing the P0650 code will set. A voltage is supplied directly to the malfunction indicator lamp (MIL). The Powertrain Control Module ( PCM) controls the lamp by grounding the control circuit via an internal switch called a driver.

How much does it cost to diagnose GMC code p0650?

The cost of diagnosing the P0650 GMC code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. When is the P0650 GMC code detected?

How does the Powertrain Control Module ( PCM ) work?

The Powertrain Control Module ( PCM) controls the lamp by grounding the control circuit via an internal switch called a driver. The primary function of the driver is to supply the ground for the component being controlled. Each driver has a fault line which is monitored by the PCM.