Easy tips

What does the error code p1626 stand for?

What does the error code p1626 stand for?

Error Code P1626 is defined as Theft Deterrent Fuel Enable Signal Not Received. This error code is a manufacturer-specific trouble code, meaning it does not apply to all vehicles makes.

What does p1626 Chevrolet theft deterrent code mean?

P1626 Chevrolet Meaning. The Body Control Module (BCM) produces the theft deterrent fuel enable signal when the ignition is ON and the proper key resistor pellet is sensed. The powertrain control module (PCM) monitors the fuel enable signal during crank.

How does DTC p1626 work in a car?

The powertrain control module (PCM) monitors the fuel enable signal during crank. If the proper signal is present on the class 2 serial data circuit, the PCM enables the fuel delivery in order to allow the engine to start. If the PCM determines that the fuel enable signal is not present or incorrect while the engine is running, DTC P1626 is set.

How do I Fix my GMC p1626 code?

Turn ignition on. 2. Attempt to start the engine, and then release the key to the “ON” position. 3. Observe the “SECURITY” indicator light. After 10 minutes the “SECURITY” indicator light will turn off. 4. Turn ignition to the “OFF” position, and wait 10 seconds. 5. Attempt to start the engine, and then release the key to the “ON” position. 6.

Why do I have p1626 code on my car?

This can be from a faulty BCM which is common in these cars. The body control module (BCM), produces the theft deterrent crank relay and fuel enable signal when ignition is ON and the proper ignition code voltage value is detected. The powertrain control module (PCM) monitors the fuel enable signal during crank.

What happens if DTC p1626 is not stored?

The engine continues to start and run as long as DTC P1626 is stored. If the problem affects inputs to the Vehicle Theft Deterrent System (VTD) signal, the starter motor may be disabled. The engine is running. The PCM has detected a loss of the state of health serial data message from the theft deterrent system.

How much does it cost to repair a p1626 Chevy?

Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P1626 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city.

How to fix code 1626 on Snap on scanner?

So I put my snap on scanner on it it has code 1626, u1000, code 1626 is theft deterrent system fuel is disable u1000. How do I get it running? Is there a way to get it running by key learning? I have tried key in for ten minutes and pull key out for less then twenty seconds and do it again.

Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P1626 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city.

What does no crank mean on DTC p1626?

The numbers below refer to the step numbers on the diagnostic table. An engine that does not crank and a DTC P1626 is set, indicates that there is a theft deterrent system condition. An incorrect ignition key or an incorrect starting procedure causes a no crank condition.

Why do I get a p1626 code on my Astrovan?

A GM problem. When the PASSKEY MODULE goes bad, a 1626 code is hard and nothing other than a replacement module (not available) or a BYPASS MODULE is available. Then the problem is forever solved. Worked on my 1999 AstroVan and it starts everytime. My 99 tahoe starts and dies and I get this P1626 code. So how do I trouble shoot this problem?

How much does it cost to repair a p1626 Chevrolet?

Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P1626 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type.

Error Code P1626 is defined as Theft Deterrent Fuel Enable Signal Not Received. This error code is a manufacturer-specific trouble code, meaning it does not apply to all vehicles makes.

Turn ignition on. 2. Attempt to start the engine, and then release the key to the “ON” position. 3. Observe the “SECURITY” indicator light. After 10 minutes the “SECURITY” indicator light will turn off. 4. Turn ignition to the “OFF” position, and wait 10 seconds. 5. Attempt to start the engine, and then release the key to the “ON” position. 6.

How to turn on theft deterrent in DTC p1626?

Go to Step 4 Go to Vehicle Theft Deterrent (VTD) System Checkin Theft Deterrent 4 Turn OFF the ignition. Disconnect the BCM connector. Refer to Body Control Module Replacementin Body Control System. Turn ON the ignition leaving the engine OFF.

Author Image
Ruth Doyle