Easy tips

What does it mean when your car says no start?

What does it mean when your car says no start?

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).

How to troubleshoot a no start GM 4.3L pick up?

Testing a Cranks but Does Not Start condition on your GM 4.3L, 5.0L, 5.7L pick up, van or SUV is not that hard to do, if you have a solid diagnostic strategy. In this article I’ll show you the basics of testing such a problem.

What makes a 1997 GMC C2500 no start?

1997 GMC C1500, C2500, C3500 Pick Up. 1997 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a misfire or a no-start problem (caused by the ignition coil, the ignition module, or the crankshaft position sensor).

How can I tell if my starter motor is bad?

Important Safety Precautions. STARTER TEST 1: Applying 12 V To The S Terminal. STARTER TEST 2: Verifying The Start Signal. STARTER TEST 3: Voltage Drop Testing The BATT (+) Cable. Symptoms Of A Bad Starter Motor.

What causes a Chevy Astro van to not start?

In the Chevy Astro van, power is supplied to the fuel pump by the the gray wire on the electrical connector when the engine is being cranked. If power is supplied, hitting the fuel tank with the flat side of a hammer while someone else is turning the ignition key to start will sometimes bump the fuel pump enough to allow it to start.

Where is the fuel pump on a Astro van?

If it is good, check for power at the fuel pump electrical connector located near the rear of the fuel tank on the driver’s side of the van. In the Chevy Astro van, power is supplied to the fuel pump by the the gray wire on the electrical connector when the engine is being cranked.

What should battery voltage be in Astro van?

A measurement of 12.5 volts is considered discharged, and the battery should be charged before any further testing. Any measurement below 11 volts indicates a severely discharged battery–the battery is most likely damaged and should be replaced. If the battery measures above 12.7 volts, proceed to the next step.

Why does my car not start when I turn the key?

This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start. A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine.

What’s the difference between no start and no crank?

It’s important to know that a no crank and a no start condition are not the same thing since this article only concentrates on testing a no start condition. In layman’s terms, a No Start Condition means that your vehicle’s starter motor is cranking the engine but the engine is not starting.

A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine. The most common problem, that causes this condition is a failed starter motor. If your vehicle is suffering a No Crank Condition, this tutorial may be a good starting point: How To Test The Starter Motor (GM 4.3L, 5.0L, 5.7L).

This condition is usually due a failed fuel pump, a failed ignition coil, a failed ignition control module, a failed crank sensor, etc… that lets the engine crank (turn over) but does not let it start. A No Crank Condition means that the engine is not turning over when you turn the key to crank the engine.

It’s important to know that a no crank and a no start condition are not the same thing since this article only concentrates on testing a no start condition. In layman’s terms, a No Start Condition means that your vehicle’s starter motor is cranking the engine but the engine is not starting.

Why does my GM 4.3L engine not start?

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

Why is my Chevy Silverado 1500 not starting?

However, today, when the truck will crank and start, the antitheft icon goes off after a few seconds with the key on and stays off while the truck is running. It never flashed either today or yesterday though. And I don’t know if the antitheft system disables cranking or starting or both.

What causes a car to start at the wrong time?

Spark plug wires are a source of electromagnetic interference (EMF), but this is usually only a problem on some aftermarket setups when this interference isn’t taken into account. A timing belt or chain that has skipped a tooth will throw off the cam timing, causing the intake and/or exhaust valves to open at the wrong time.

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

When does a Chevy Monte Carlo not start?

2002 Chevrolet Monte Carlo. Consumer states vehicle will not start when the weather is hot weather, and should subject to a safety recall. The contact owns a 2007 Chevrolet Monte Carlo. The contact stated that the vehicle failed to restart after being shut off. The vehicle restarted after approximately forty minutes.

What kind of car won’t start when parked?

The contact owns a 2003 Chevrolet Monte Carlo. While parked, the vehicle failed to start and the key remained in the off position. The vehicle was not diagnosed or repaired. The failure recurred on numerous occasions. The vehicle was included in NHTSA campaign number: 14v400000 (electrical system).

What kind of problems does a Monte Carlo have?

The contact owns a 2007 Chevrolet Monte Carlo. The contact stated that the vehicle failed to restart after being shut off. The vehicle restarted after approximately forty minutes. The vehicle was not diagnosed or repaired.

Can a PassLock system failure cause a no start?

Passlock system failures are a very, very common cause of no start conditions. OK, the list of possible things that can go wrong looks pretty long but it is rare to see (or have) two different components go bad from two separate systems at the same time.

What to do if spark doesn’t work on S-10 Blazer?

If the spark is weak or doesn’t happen, replace the coil. Remove the plug wire from a spark plug, leaving it attached to the distributor cap (or coil pack on S-10s with distributor-less ignition systems) and turn the ignition key to the “Start” position. A bright spark should cross an inch or more to the engine block.

How to troubleshoot a Chevy S-10 Blazer ignition system?

Attach the black (negative) and red (positive) clips on the tester to the battery. Turn the key to the “Run” position and touch the probe end of the tester to the two wires on the coil by inserting the probe into the back of the electrical connector.

What to do if your blazer has no power?

If no power is present, replace the brown fusible link on the back of the Blazer’s starter. If power is shown on one wire and ground is shown on the other wire, replace the coil. Remove the electrical connector from the coil and back-probe the ground wire.

What are common reasons my Chevrolet Astro won’t start?

What are common reasons my Chevrolet Astro won’t start? While there are a variety of reasons your Chevrolet Astro won’t start, the most common 3 are a dead battery, an alternator problem, or failed starter.

Testing a Cranks but Does Not Start condition on your GM 4.3L, 5.0L, 5.7L pick up, van or SUV is not that hard to do, if you have a solid diagnostic strategy. In this article I’ll show you the basics of testing such a problem.

When do you turn on the cooling fan on a Camaro?

On some vehicles the factory cooling fan is not triggered until well over 200 degrees F. This robs your engine of performance and the tendency to pre-detonate is much greater.

What causes an engine to start but not run?

An engine will start but not run when the fuel runs out . If the fuel pressure is not strong enough the car will stall out . Was this answer helpful? sailer342 , Stalling issues bad sensors TPS, MAP, MAF, IAC, O2, failing knock senor, faulty injectors, dirty throttle body, EGR valve, vacuum leak, failing fuel pump, etc.etc..

Why does my Chevy Camaro engine not start?

There are a lot of issues that can cause your Camaro to crank, but not start. The engine needs air, fuel, and a spark in order to run. It is highly likely that if the engine is cranking, but not starting that it has thrown an OBDII code. It is definitely worth it to use an OBDII scanner to check and see if the engine has thrown any trouble codes.

What causes a car to have a no start condition?

The engine pistons and valves (and all the other related components like: timing chains, etc.) are the ones responsible for the induction of the fresh air the engine needs for the combustion process. Although rare, internal engine mechanical problems can and do cause no-start conditions. Blown head gasket. Blown engine. 4.)

What to do if your GM pick up has no start?

One of the most overlooked areas, when testing a hard to diagnose no-start, is the mechanical condition of your 4.3L, 5.0L, 5.7L GM pick up, van or SUV. Checking the engine mechanical condition means an engine compression test.

What to do if your Chevy Silverado won’t start?

Change hole top of the motornew head gasket new intake preface vale seats new valve seals valve covergaskets new battery new belt plugs wires now it won’t start or even turn over what’s is my problem Truck won’t start and the alternator puts outs 14 volts . Turn keys nothing. It starts sometimes but not always . It start right away with a boost

Why does my car not start when I crank the engine?

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

What should I do if my truck won’t start?

Q: My truck won’t start, battery is good, alternator is good, don’t know if its starter, was told might have to change neutral lock. How do i figure out what it is without being able to move it because it won’t start and it will cost more to tow it.

What can cause my truck not to crank up?

If the fuel pump malfunctions or is going bad, it can cause the engine not to start even with the starter can cranking properly. 2) Battery Issues If the engine cranks too slow, there might be a battery issue that is causing it. Perhaps your battery is low on power or there is corrosion on the terminals of your battery.

Why is my truck not getting fuel?

Here are some additional reasons that specific types of vehicles may not be getting enough fuel. Gasoline- and diesel-powered vehicles: If you have a modern vehicle with a multiport or sequential fuel injection system, either the fuel pump isn’t pumping fuel or the ECU isn’t triggering the fuel injectors.

Why wont my Truck turn over?

A Common Engine Performance Problem. The engine not turning over is a common engine performance problem. The root cause may range from a loose wire to a more serious mechanical issue. Fortunately, most of the problems that may prevent your engine from turning are possible to diagnose at home.

To restate what a crank/no start is, it’s when you turn the key and you can hear the engine moving but it’s just not catching and running. You can first eliminate all the above causes in this article because you have confirmed that your starter, cables, and battery connections are likely good.

What should I do if my bike wont start?

Charge the battery or replace it if it’s dead. Am easy way to test your battery is by checking the voltage-drop with a multimeter as you try starting the bike. If your fully charged battery drops below 11,5 volts under load (while you crank the starter), it needs to be replaced.

What does it mean when your ATV won’t start?

The solenoid should make an audible “clicking” sound each time you hit the starter. If it does, you know it is getting power, and the problem is likely with the solenoid itself or possibly the starter.

What should I do if my outboard motor wont start?

Once you’re sure the outboard is getting electricity, the next thing to check is whether it’s getting any fuel. Make sure the outboard is fully primed with fuel. If the fuel pump isn’t primed, the motor may turn over without starting. Squeeze the primer bulb a couple of times to prime the fuel pump.

Can a bad crank sensor cause a car to not start?

Both of these have a history of failing when they are hot and coming back to life again when they are cold. A bad crank sensor will almost certainly result in a code, but an ignition module might not.

What to do if your small engine won’t start?

Determine why your small engine won’t start by checking your fuel levels, spark plug, carburetor, valve & compression levels and more. Follow along to troubleshoot and learn when it’s best to service your engine.

What does it mean when your car won’t start?

Usually if you have a malfunction that prevents the car from starting, there will be a code resulting. That being said, it sounds like you may have an issue with a crank position sensor or an ignition control module. Both of these have a history of failing when they are hot and coming back…

What to do if your Jeep won’t start?

Jeep won’t start. One click when key is turned. Confirm that the engine immobilizer system (security system) is not activated thus preventing the car from starting. If the immobilizer system is on, you may see a security warning light.

What to look for when your engine won’t start?

Check for a blown fuse that may be preventing a circuit from working properly, like the fuel injection or computer system. To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition).

Why does my car turn over but not fire?

Sometimes your engine does turn over but will not actually fire. The culprits in this instance can include everything from distributors to coils, fuel pumps to fuel filters, spark plugs to plug wires. In this case, it might be worth it to drop the car off for a session with the professionals.

What kind of truck won’t start or fire?

I have a 1997 Chevy Z71 just put new trans in drove for about 20 miles and the truck just died………Replaced fuel pump, Fuel relay and found that the fuel fuzz blows every time I turn key on ???? 24 people found this helpful. 22 people found this helpful.

Why does my car engine not want to start?

If the engine still doesn’t seem like it wants to start, probably fuel is getting into the cylinders and your problems lies somewhere else. However, if the engine runs momentarily and dies, then the problem is that fuel is not getting to the cylinders. Check for a clogged fuel filter, or a bad fuel pressure regulator.

What does no crank no start car mean?

Mechanics refer to this as a no crank no start condition. Of course, the number one reason for an engine not the crank on any car would be a problem with the battery. Since classic car owners are familiar with how to treat a battery during long-term storage we’ll just touch on this briefly and then move on.

Why does my Ford F150 not start up?

STARTING PROBLEM I have a 2000 ford f150 5.4L the truck cranks but will not start some times. if i spray starter fliud into the booster in will start up. but other times the truck will start then just idle off. There is good fuel psi, just changed the fuel pump relay. the problem stop for a while then started again.

What does it mean when your F150 won’t start?

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. This just means that the engine doesn’t move when you turn the key. The second way that your F150 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

What does it mean when your tractor won’t start?

If you’re storing something behind the seat and it shifts, it may keep the seat from coming down on the switch and the tractor thinks you’ve fallen off and it won’t start. Or, you could have the weight springs set too light, that’ll be the subject of a future video.

Why does my car engine won’t start?

My Engine Turns Over OK But It Won’t Start If your engine won’t crank or turn over, go HERE. So you know your battery is good and the starter works OK because the engine turns when you try to start it. You crank and crank and crank but it just won’t run. There are many reasons why an engine won’t start. It’s usually something simple.

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. This just means that the engine doesn’t move when you turn the key. The second way that your F150 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

What to do if your Toyota won’t start?

Battery – If the connections on your battery become corroded, there is no longer a connection to the rest of the car. This can keep you from starting. Clean the posts and try to start the car. Additionally, the battery may be dead. Take a battery tester and test the cranking amps to see if they are weak.

In a no crank condition, the engine is not cranking when you turn the key to crank the engine. In other words, you turn the key and nothing happens since the engine won’t turn over. This usually due to a bad starter motor or a bad starter motor solenoid. Remember this article only deals with a no start condition.

How to troubleshoot a Ford 4.9L no start?

Part 1 -How to Troubleshoot a No Start (Ford 4.9L, 5.0L, 5.8L). Troubleshooting a no start problem on your Ford 4.9L, 5.0L, or 5.8L pick up, van, or SUV can be easily done, with the right diagnostic information and troubleshooting strategy and in this article I’ll provide you with some of both.

In other words, you turn the key and nothing happens since the engine won’t turn over. This usually due to a bad starter motor or a bad starter motor solenoid. Remember this article only deals with a no start condition.

Since a lot of folks confuse a no crank condition with a no start condition, I’ll clear it up right now: In a no start condition (also known as a cranks but does not start) your vehicle’s starter motor is cranking the engine but the engine is not starting.

In a no crank condition, the engine is not cranking when you turn the key to crank the engine. In other words, you turn the key and nothing happens since the engine won’t turn over. This usually due to a bad starter motor or a bad starter motor solenoid. Remember this article only deals with a no start condition.

Part 1 -How to Troubleshoot a No Start (Ford 4.9L, 5.0L, 5.8L). Troubleshooting a no start problem on your Ford 4.9L, 5.0L, or 5.8L pick up, van, or SUV can be easily done, with the right diagnostic information and troubleshooting strategy and in this article I’ll provide you with some of both.

Since a lot of folks confuse a no crank condition with a no start condition, I’ll clear it up right now: In a no start condition (also known as a cranks but does not start) your vehicle’s starter motor is cranking the engine but the engine is not starting.

Can a blown head gasket cause no start?

The engine pistons and valves (and all the other related components like: timing chains, etc.) are the ones responsible for the induction of the fresh air the engine needs for the combustion process. Although rare, internal engine mechanical problems can and do cause no start conditions. Blown head gasket. Blown engine.

What to do if your Bronco won’t start?

Bronco will just “die” while going down the road. After sitting for a while, it will start back up. Usually has not happened in problem traffic. I have not replaced the ignition module yet. I found this site while searching for a solution to my problem. Starts fine in morning. Drive 4-5 miles, stalls. Will restart after about 1 hour.

What makes a Ford 4.9L engine not start?

Without spark, the engine will crank but not start. Ignition control module (ICM). Depending on the year of your specific Ford, it’ll have a inner-fender mounted ignition control module or a distributor mounted ignition control module.

Without spark, the engine will crank but not start. Ignition control module (ICM). Depending on the year of your specific Ford, it’ll have a inner-fender mounted ignition control module or a distributor mounted ignition control module.

What causes a car to have no start?

1 The engine pistons and valves (and all the other related components like: timing chains, etc.) are the ones responsible for the induction of the fresh air the engine needs for 2 Although rare, internal engine mechanical problems can and do cause no start conditions. 3 Possible internal engine problems are: Blown head gasket. Blown engine.

Why does my Troy Bilt lawn mower not start?

My troy bilt bronco lawnmower turns over but will not start I have changed the fuel, the fuel filter and spark plug but it still does not start. I am stuck

The engine pistons and valves (and all the other related components like: timing chains, etc.) are the ones responsible for the induction of the fresh air the engine needs for the combustion process. Although rare, internal engine mechanical problems can and do cause no start conditions. Blown head gasket. Blown engine.

What was the top of the line Ford Bronco in 1978?

The Bronco Custom served as the standard-trim model with the Bronco Ranger XLT as the top-level trim. For 1978, as with the F-Series trucks, Customs were fitted with round headlamps while Ranger XLTs had rectangular units, which became standard for all Broncos for 1979.

When did the second generation Ford Bronco come out?

For the 1978 model year, the second-generation Bronco was introduced; to better compete with the Chevrolet K5 Blazer, Dodge Ramcharger, and Jeep Cherokee, the Bronco entered the full-size SUV segment. In place of a model-specific chassis, the Bronco was adapted directly from the Ford F-Series, becoming a shortened version of the F-100 4×4.

When did the Ford Bronco Sport become freestanding?

For 1970, the Bronco Sport became a freestanding model rather than an option package. To comply with federal regulations, the Bronco was fitted with backup lights and side marker lamps (in 1967 and 1968, respectively).

When did Ford stop making the Bronco half cab?

After 1972, the Bronco half-cab was withdrawn; along with its lower sales compared to the wagon, Ford had introduced the larger Ford Courier compact pickup. In a minor revision, for 1977, the exterior-mounted fuel tank caps were replaced behind hinged doors (as on all other Ford trucks).

In other words, you turn the key and nothing happens since the engine won’t turn over. This usually due to a bad starter motor or a bad starter motor solenoid. Remember this article only deals with a no start condition.

A no start condition is usually due to a problem provoking a lack of fuel or spark to the engine and this tutorial concentrates on troubleshooting this type of problem. A no crank condition means that the engine is not cranking when you turn the key to crank the engine. If your Ford vehicle is experiencing…

Why does my 2001 F150 lightning not start?

2001 f150 lightning. Not a starter or battery issue. Ran all sorts of fuel system tests. Replaced ignite coil, alternator, battery, all the basics. Won’t start only after it’s been run (like after driving it to the gym and I go to leave, won’t start).

What does a crank but not start condition mean?

Related Test Articles. You can find this tutorial in Spanish here: Cómo Probar Un Arranca Pero No Prende (4.6L, 5.4L Ford V8) (at: autotecnico-online.com ). A a cranks but does not start condition means that your vehicle’s starter motor is cranking the engine but the engine is not starting.

Why does my Ford pick up not start?

Alright, let’s get started with the next subheading. The most important thing that you need to keep in mind, when you’re faced with your Ford vehicle cranking but not starting is that the engine needs air, fuel and spark to start. If any one of these is missing from the mix, your 4.6l, 5.4L Ford pick up (car, van, or SUV) will not start.

A no start condition is usually due to a problem provoking a lack of fuel or spark to the engine and this tutorial concentrates on troubleshooting this type of problem. A no crank condition means that the engine is not cranking when you turn the key to crank the engine. If your Ford vehicle is experiencing…

How old is a 2001 Ford F-150 SuperCrew?

2001 4×4 5.4L purchased in 2001, traded in 2015 for new F-150. Never any problems. Normal repairs – brakes, battery…didn’t need front axles until 2014. And that was with a 3″ level kit. 14 years of perfection. I hope my 2015 F-150 does as well.

Related Test Articles. You can find this tutorial in Spanish here: Cómo Probar Un Arranca Pero No Prende (4.6L, 5.4L Ford V8) (at: autotecnico-online.com ). A a cranks but does not start condition means that your vehicle’s starter motor is cranking the engine but the engine is not starting.

Can you test a Ford 4.6L in no start?

Testing a cranks but does not start condition on your Ford 4.6L, 5.4L car, pick up, van or SUV can leave you scratching your head and wondering where to start and/or what to test. Well, I can tell you that testing a no start doesn’t have to turn into a nightmare and that you can save money by testing certain components before replacing them.

Alright, let’s get started with the next subheading. The most important thing that you need to keep in mind, when you’re faced with your Ford vehicle cranking but not starting is that the engine needs air, fuel and spark to start. If any one of these is missing from the mix, your 4.6l, 5.4L Ford pick up (car, van, or SUV) will not start.

Is the Check Engine light blinking when turning on?

Light blinks like crazy will turn over no start . also code 11 blinks once and then a again a sec later . ive tryed everything read the codes no codes but the check engine light is on? It doesnt stay on for 1 sec let alone 3 when turning on?

What causes a Lincoln Town Car to not start?

When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your Town Car, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it. There are a lot of issues that can cause your Town Car to crank, but not start.

How to troubleshoot a no start Ford 4.9L?

Once you’re tapped in, have a helper crank the engine while you observe your multimeter in Volts DC mode. If voltage is present (12 Volts), then you have confirmed that the fuel pump fuse, fuel pump relay and inertia switch are working perfectly.

Why does my fuel pump say no start?

If no voltage is present, as your helper cranks the engine, then the cause of no fuel condition is due to either a BAD fuse, fuel pump relay, or inertia switch. The following tutorial will help you to test the fuel pump: How To Test The Fuel Pump -No Start Test (Ford 4.6L, 5.4L).

When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your Town Car, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it. There are a lot of issues that can cause your Town Car to crank, but not start.

If no voltage is present, as your helper cranks the engine, then the cause of no fuel condition is due to either a BAD fuse, fuel pump relay, or inertia switch. The following tutorial will help you to test the fuel pump: How To Test The Fuel Pump -No Start Test (Ford 4.6L, 5.4L).

Once you’re tapped in, have a helper crank the engine while you observe your multimeter in Volts DC mode. If voltage is present (12 Volts), then you have confirmed that the fuel pump fuse, fuel pump relay and inertia switch are working perfectly.

What causes an engine to turn over but not start?

So if there is any problem with the injector, it may cause the engine turns over but won’t start. For this, you will need to test the working of the injectors using a computer. Testing is done by using a test light while the engine is cranking. Many a time, you may not know the fault in the vehicle.

What to do if your car turns over but won’t start?

If there is plenty of gas but no spark, the engine will crank but not start. Unplug one of the spark plug wires and plug in a spark tester. Have a friend get in the car and crank the engine while you watch to see if the spark tester illuminates. You can usually purchase a spark tester at an auto parts store for about ten dollars.

Why does my car not start when I Turn on the engine?

False input or lack of input from sensors like the crankshaft position sensor (CKP) or camshaft position sensor (CPS) can prevent the engine from starting. Also, a bad throttle position sensor (TPS) may cut off the spark to the cylinders. Battery.

What should I do if my advance car won’t start?

Advance carries compression testers that thread into the spark-plug holes and read compression when you turn the engine over. After making sure the engine won’t start when you crank it, remove one plug and thread the tester in the hole. Crank the engine for two to three seconds and read the gauge.

What should I do if my car engine is not cranking?

If your engine is not cranking, make sure that the car battery is charged and that it’s not failed. You can either try to jump start it from another car or with the help of a jump starter. You can also work with a different car battery if you have one at home. If the battery is good and the jump start didn’t help the engine to crank.

Check for a blown fuse that may be preventing a circuit from working properly, like the fuel injection or computer system. To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition).

Author Image
Ruth Doyle