What does fmi7 stand for on mid128 pid411?

My sheet shows MID128 PID411 is ” EGR Exhaust Back Pressure” but shows the FMI to be either 2,3 or 5. But FMI7 is listed as “Mechanical fault” – “Mechanical system not responding properly”

What is the SPN code for a FMI PID?

SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 132 7 PID 132 1213 Intake Air Throttle Valve Closure Detection- Positive Torque 132 14 PID 132 1213 Intake Air Throttle Valve Closure Detection -Braking Condition 132 14 PID 322 1635 HC-Doser Fuel Pressure Not Plausible 132 1 PID 322 1213 Air Mass Flow Too Low

What does fmi7 stand for in a diagnostic code?

But FMI7 is listed as “Mechanical fault” – “Mechanical system not responding properly” If that’s right, I’d bet Jim should be looking at the exhaust gas pressure sensor. They have a habit of getting plugged with soot, and then becoming sluggish or ending up with readings that don’t make sense.

What is the diagnostic code for fmi7 HDT escapees?

He said that sometimes a sensor line gets plugged with soot and causes the computer to “complain.” The fault code was MID128 PID411 FMI7. The CHECK light came on a second time. And, then it “cleared” itself, as I was driving down the road.

What is code for mid 128 Sid 27 FMI 7?

BTW – The mechanic found another code MID 128 SID 27 FMI 7. Apparently the turbo was NOT working as it should have been. All it needed was a recalibration. On the drive home, I noticed that turbo pressure would rise, as I was driving. I never saw that before.

What is the engine coolant sensor code in FMI?

110 2 PID 110 1212 Engine Coolant Sensor (OUT), General Temp. Plausibility Error SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 132 7 PID 132 1213 Intake Air Throttle Valve Closure Detection- Positive Torque 132 14 PID 132 1213 Intake Air Throttle Valve Closure Detection -Braking Condition

What does FMI 14 mean on a Volvo?

FMI 14 The code informs you that the electric fuel pump has been turned on. Not a malfunction code. FMI 1 Low engine oil level, level sensor faulty. FMI 4 The voltage at the contacts of the engine block EV15-EB22 is lower than 0.5 V. A short to negative or to a signal wire. The level sensor may be faulty.

What is the ISX fault code for a Cummins Engine?

A complete list of all fault codes for the Cummins ISX engine (before 2002). Here are all the Cummins ISX fault codes available for the Cummins ECM. These Cummins trouble codes pertain to ISX engines built without the EGR system (before 2002). 153 Intake Manifold Temperature Sensor Circuit 154 Intake Manifold Temperature Sensor Circuit

What causes a mid 128 fault in a Mack truck?

Volvo, Renault, Mack Trucks – MID 128 The voltage at the contact of the EA6 engine block is higher than 65% of the battery voltage, a short to positive, a break in the power or ground wire, a sensor malfunction on the fan. The fan rotates at maximum speed, which causes high fuel consumption

What is the fault code for a mid 128 engine?

Engine ECU Faults (MID 128) Fault Code Description FMI Codes MID 128 PID 26 Engine Fan Speed Percent 3,8 MID 128 PID 27 EGR Valve #1 Position Sensor 3,4,5 MID 128 PID 45 Preheater Relay Status 3,4,5 MID 128 PID 81 Particulate Filter 0,2,3,5,12

What is FMI 1 for Volvo mid128 engine?

FMI 1 For engines D6B, D7C, D10B, D12C: The fuel pressure is below normal. The fuel filter is clogged, fuel leakage, air leakage, the bypass valve opens at low pressure, the mechanical pump does not pump well or the sensor is faulty.