What do I need to replace serpentine belt on Dodge Ram?
What do I need to replace serpentine belt on Dodge Ram?
Make sure the shielding around your wheels and engine is attached for full serpentine belt life. The procedure for the 5.7 Hemi engine differs from the 3.7/4.7 engines. For owners with the 5.7 liter engine, you will need a 3/8″ ratchet (preferably long-handled).
How do you remove a serpentine belt from a car?
Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.
What kind of engine does a Dodge Dakota have?
The 4.7l V-8 Dodge engine is popular in the Dodge Dakota, mainly because of its high horsepower numbers in a low weight chassis. Like many modern V-8 engines, several critical engine parts and accessories are driven by a single belt, known as a serpentine belt.
How do you install a serpentine belt on a water pump?
Begin the 4.7 and 3.7 serpentine belt installation by routing the belt around the alternator/generator pulley then under the water pump pulley. Now move it over the A/C pulley and down the outside of the tensioner.
How to replace a serpentine belt for Chrysler 3.7?
Hi, Martin here! I’m the proud owner of a 98 Jeep Cherokee XJ & 04 Jeep Grand Cherokee WJ. I produce videos where I customize and service these 2 Jeeps. Enjoy doing mods to engine, drivetrain, suspension, body, and interior and some that have never been done before and bring it to you!
The 4.7l V-8 Dodge engine is popular in the Dodge Dakota, mainly because of its high horsepower numbers in a low weight chassis. Like many modern V-8 engines, several critical engine parts and accessories are driven by a single belt, known as a serpentine belt.
How do you replace the belt on an engine?
Loop the replacement belt on the engine following the path laid out on the routing diagram. Run it around every pulley except the idler pulley, making sure the belt doesn’t twist or kink along the way. Pull up the tensioner again with the breaker bar, then pull the belt over the idler pulley.
What to do if your serpentine belt stops working?
If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. Hi, Martin here!
What kind of belt does a Dodge Ram have?
The main drive belt or serpentine belt is important on any vehicle, but some have more than one belt to drive components from the crankshaft. The Dodge Ram and similar truck models have one true serpentine belt, a multi-ribbed belt that fits into grooves on various pulleys, that Dodge suggests inspecting for wear every 15,000 miles or 12 months.
Where is the 15mm headed bolt on a Dodge Ram?
The red circle indicates the location of the 15mm headed bolt on the 4.7 and 3.7 engines. With the belt off, compare the sizes of both the old and new. They should be similar in length, and the number of ribs needs to be the same. The ribbed side of the belt will face the ribbed pulleys, and the smooth side of the belt will face the smooth pulleys.
Can a serpentine drive belt be changed on a Dodge Hemi?
This is a step by step instructional video on how to replace your serpentine drive belt on your dodge hemi v8 engine. The belt tensioner is also changed during the process. Whether you have a Ram Truck, Challenger, Charger, or Magnum Hemi engine, the repair will be similar to what is shown here. Loading…
What kind of belt does a Dodge Ram use?
Since the Ram uses the serpentine belt to rotate the water pump, when the belt breaks you are forced to come to a stop. This article applies to the Dodge Ram (2002-2008). The serpentine belt is made of a rubber compound and is grooved for optimal friction with the accessory pulleys.
The red circle indicates the location of the 15mm headed bolt on the 4.7 and 3.7 engines. With the belt off, compare the sizes of both the old and new. They should be similar in length, and the number of ribs needs to be the same. The ribbed side of the belt will face the ribbed pulleys, and the smooth side of the belt will face the smooth pulleys.
Begin the 4.7 and 3.7 serpentine belt installation by routing the belt around the alternator/generator pulley then under the water pump pulley. Now move it over the A/C pulley and down the outside of the tensioner.
