What causes Service StabiliTrak warning on Chevy Avalanche?

Wheel Speed Sensor – If one of the wheel speed sensors is out, your Avalanche will no longer be able to tell if all of the wheels are turning at the same speed. Without this data it’ll turn on the service StabiliTrak warning.

When is the Avalanche traction control light on?

Chevrolet Avalanche Traction Control Light is on Inspection at your home or office. Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM. Our certified mobile mechanics can come to you now.

Is it time to service your Chevy Avalanche?

If it works after firing your Avalanche back up, great! If not, it may be time to have it serviced. While it won’t hurt to drive your Chevy Avalanche without traction control or StabiliTrak, you are operating it without an important safety feature.

What causes wheel rotation warning on Chevrolet Avalanche?

Anything the interferes with correct wheel rotation can trip this warning. Did you change tires, have brakes serviced or hit a pothole real hard? Believe it or not even a weak battery can cause warnings of this type due to voltage fluctuations. There are sensors in you wheels that monitor rotation speed, braking and position.

What does StabiliTrak do on a Chevy Avalanche?

One of the most common issues with the Chevy Avalanche, or any newer GM vehicle is the “Service StabiliTrak” warning. StabiliTrak is one of the most innovative and important safety features on a GM vehicle. StabiliTrak is designed to help prevent accidents by giving you better control of your Avalanche.

Who is the owner of the 2005 Avalanche?

2005 Chevrolet Avalanche Owner ManualM GENERAL MOTORS, GM, the GM Emblem, CHEVROLET, the CHEVROLET Emblem, and the name AVALANCHE are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.

Can you drive a Chevy Avalanche without traction control?

While it won’t hurt to drive your Chevy Avalanche without traction control or StabiliTrak, you are operating it without an important safety feature. If there’s anything you’d like to add, please leave a comment below.

How to reset TPMs on old Chevy Avalanche?

There are 3 ways to reset TPMS on the old Chevrolet Avalanche. Please choose 1 of the two ways below according to your vehicle specifications. Time needed: 7 minutes. If you have 2004 2005 2006 Avalanche, you can reset the TPMS by increasing or decreasing the tire pressure without using tools. Follow these instructions to get started:

Why is my traction control not working on my Avalanche?

Traction Control Not Working – Your Avalanche’s traction control system mostly uses the same sensors to determine if a wheel has broken traction. Unlike StabiliTrak, which controls lateral issues (sliding), traction control keeps the wheels from unnecessary spinning.

What is the owner manual for a 2011 Avalanche?

Chevrolet Avalanche Owner Manual – 2011 Black plate (27,1) In Brief 1-27. On all vehicles, the Engine Oil Life System can be reset as follows: 1. Turn the ignition to ON/RUN with the engine off. 2. Fully press the accelerator pedal slowly three times within five seconds.

Why are my abs and brake lights not working?

This is how I fixed my intermittent ABS and Brake dash lights on my Chevrolet blazer with the Kelsey-Hayes EBCM module, with out spending 1500 bucks on a new EBCM.. You may have code C0265 “Electronic Brake Control Module Motor Relay Circuit.” The fault is usually due to broken solder joints on the circuit board.

How to repair a 2006 Chevy Avalanche 1500?

Chevrolet Repair 2006 chevy avalanche 1500: light comes..traction control..my brakes… Customer Question I have a 2006 chevy… I have a 2006 chevy avalanche 1500 and my sevice stability light comes on and traction control also. When i put into drive and leave it sometimes goes away.

What happens if you reset your fuel gauge?

Electronic and software malfunctions may cause the fuel gauge in your automobile to inaccurately measure or display the amount of fuel remaining in the gas tank. If this happens, reset your fuel gauge. Each make and model of car has its own specific instructions on how to reset the fuel gauge, but the process is basically the same. Step 1

What are the problems with the Chevrolet Avalanche?

The Avalanche has the loss of instrument read outs. The Speedometer sometimes will show you going faster or slower than you really are. We use our GPS to make sure on the highway we are within the speeds.The tackometer drops off line from time to time, and the oil pressure guage does pretty much the same thing.

How many miles does a Chevy Avalanche have?

Our 2004 Chevy Avalanche has 56,000 miles on it. The wife drives this truck and most of the miles put on it over the years have been from road trips on vacation and visiting the kids. After returning from Jacksonville a couple of weeks ago a noise from the wheels kept getting louder and louder.

What’s the charge gauge on my Chevy Avalanche?

The electrical charging gauge was pegged past the upper limit of 19 volts. Once on an analyzer it was assured that my charging system was fine but I was told that the gauge was bad and I had to replace it.

Why is the a / C not working on my Avalanche?

The on board read out on the dash keeps going into another language and will not reset by just holding the button it. The A/C slips from cold to heat on one side and you have to restart the truck to get it back on cold. This problem I believe has more to do with the little relays that are located in the fuse compartment under the hood.

How does the 4WD light work on a Chevy Avalanche?

The vehicle will transfer into 4wd with out being selected. All the lights in the switch work, but it will not shift from 2wd to any other position. when the button is pushed the light blinks and nothing happens. The TIC displays “service 4wd”.

Where are the controls on a Chevrolet Avalanche?

If the seats have power lumbar, the controls used to operate this feature are located on the outboard side of the seats. •To increase lumbar support, press and hold the front of the control. •To decrease lumbar support, press and hold the rear of the control. •To raise the height of the lumbar support, press and hold the top of the control.

What to do if your service brake system is bad?

You need a waveform viewer to see if a hub is bad or you could use the multimeter to test resistance of the speed sensor. Another option is to swap hubs from side to side. If the right front tire now says 125mph then the hub is bad. AllOffTopic.com FTW! 1. Spin the wheel by hand as fast as possible. 2.