What are the trouble codes for International trucks?

International Trucks Diagnostics Trouble Codes (DTCs) for Model: 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, BE 200, CE Bus, CXT, DuraStar, LoneStar, MXT, ProStar, RXT, TranStar, WorkStar

When does the EPs light come on and off?

Turn the ignition switch to “on” position, the EPS light will come on then will go off after 4 seconds. 5. Within 4 seconds of the EPS light going off turn the steering wheel to the straight ahead position and release the wheel. The EPS light will then come on again 4 seconds after releasing the wheel. 6.

What are the DTC codes for ABS and EPs?

DTC 23 = A problem with the circuit for engine speed signal DTC 31 = A problem with the initial current sensor offset DTC 32 = A problem with the main current sensor offset DTC 36 = A problem with the change of the motor voltage DTC 50 – 62 = A problem with the CPU in the EPS control unit To Reset the EPS, follow these simple instructions. 1.

How can I reset the EPs on my car?

To Reset the EPS, follow these simple instructions. 1. Set the steering to straight ahead (with vehicle on ground) and switch ignition to “off” position. 2. Jump the OBD2 test port (left side of the centre consol under carpet) with a paper clip going from the bottom right pin to the 4th up from the bottom pin on the left side of the grey plug. 3.

What does the DTC code p0442 mean?

While this DTC is generic, it tells you a considerable amount about your vehicle’s evaporative emissions system. Again, this code may show up as P0442. Your car’s power control module monitors the EVAP system for leaks and other problems. If you see an EVAP leak code, you know there is likely a fuel vapor leak somewhere in the system.

What does p0404 mean on an EGR sensor?

Often times code P0404 does not actually indicate that there is something wrong with the EGR valve itself, but actually that the EGR sensor is telling your PCM that the proper amount of EGR needed to flow back into your cylinders and cool them is not present.

What to do if you find a p0442 gas leak?

If you see a P0442 evaporative emission system leak detected code, you may be able to resolve the problem without much effort. The easiest solution may be to remove and reaffix the gas cap. Once you do, clear the code on the OBD-II diagnostic scanner and drive for a few days. If the code does not return, your gas cap likely was the culprit.

What’s the trouble code for a 1995 dt466e?

That is good for 1995-1999 DT466E engines. Good Day! I’ll sticky this for you guys…. I can also post the newer engine DTC lists if you would like. If you could post the trouble codes for the later DT466E i would appreciate it. I have ordered the Intl. CD Manual but would like to start on the codes in my 2002 truck.

What’s the code for a DT 466E diesel truck?

We got couple of 05 International truck that has VGT problem. Code 152 (BAP signal out of range low). 354 (VGT control under duty cycle) and Body Controller – Remote Engine Speed Control #1 – Analog input #2 shorted to ground. Already replace BAP sensor, MAP sensor and VGT turbo.

What is the trouble code for a 1997 International 4700?

The engine I have a 1997 international 4700 with a DT 466E. The engine warning light is on, the codes are 223 and 622 … read more Vocational, Technical or Tra… Vocational, Technical or Tra… I have a 2000 dt466e engine and the oil/water just start flashing,water level ok,oil is ready for change…

What is the trouble code for 4700 dt466e?

Need trouble code info 97 International 4700 dt466e. Need trouble code info 97 international 4700 w/dt466e looking… Submitted: 8 years ago. Category: Medium and Heavy Trucks Experience: Over 16 years experience on medium and heavy duty trucks. Cyl. Contribution Test Failure – Cyl 1 Cyl. Contribution Test Failure – Cyl 2 Cyl.

What was the year of the truck 4700?

On an international truck 4900 and build date was September 1997. It has a DT466E engine in it. I think someone hook batteries up wrong or … read more 1996 4700 international 466t. Codes 621 622 224 and 615. 1996 4700 international 466t . Codes 621 622 224 and 615 … read more Vocational, Technical or Tra… Vocational, Technical or Tra…

When to warn Engine Lamp on DT 466E?

*- Indicates WARN ENGINE LAMP on when fault is set. That is good for 1995-1999 DT466E engines. Good Day! I’ll sticky this for you guys….

What is the DTC code for a truck?

INTERNATIONAL Truck Fault Codes DTC list DTC Circuit Condition Description 111 ECM No errors detected – flash code only 112 ECM PWR Electrical system voltage B+ out-of-range high 113 ECM PWR Electrical system voltage B+ out-of-range low 114 ECT Engine Coolant Temperature signal out-of-range low

What are the International fault codes for Navistar trucks?

Fault Codes DTC of International Navistar Truck 311 EOT Engine Oil Temperature signal out-of-range low 312 EOT Engine Oil Temperature signal out-of-range high 313 EWPS Engine Oil Pressure below warning level

What is the fault code for a truck?

316 EWPS Engine Coolant Temperature unable to reach commanded set point 331 ICP SYS Injection Control Pressure above system working range 332 ICP Injection Control Pressure above spec. with engine not running 333 ICP SYS Injection Control Pressure above/below desired level 334 ICP SYS ICP unable to achieve setpoint in time (poor performance)

Where do I find the Diagnostic Code on my truck?

The ability to display diagnostic trouble codes (DTC) is an optional feature. Codes may be displayed on either the gauge cluster or an optional vehicle information display (VID). The vehicle must be equipped with the option to display codes in both cases.

How to check the DTC code on a truck?

Turn the key switch to the ACCESSORY position to view only previously active codes. Turn the key switch to the IGNITION position to view both active and previously active codes. Momentarily press the Cruise “ON” switch and the Cruise “Resume” switch at the same time. A gauge sweep will be performed on the gauges.

Where can I get the OBD codes for my car?

You do this by plugging a scan tool into a computer-style port on your car (your repair manual will show you where it is) and downloading the codes. Then you can go to a site such as OBD-Codes.com and see what the codes translate into.

What does a trouble code on a car mean?

Modern vehicles have internal computers that not only control the overall performance of your car, truck or SUV, but they also alert you to a problem by generating trouble codes. Of course, if your vehicle’s computer produces one, you need to know what your trouble code means.

What kind of OBD code do I See on my car?

That is, you may see a certain code on an OBD-II system for your BMW, Chevrolet, Chrysler, Dodge, Ford, GMC, Jeep, Subaru, Toyota or another type of vehicle. Additionally, while an OBD code is not necessarily specific to a certain make or model of vehicle, the steps required to remedy it likely depend on the type of car, truck or SUV you drive.

What does the diagnostic trouble code ( DTC ) mean?

The diagnostic trouble code is the code your OBD generates to tell you something is wrong. Reading as a series of five letters and numbers, the DTC allows you to home in on the system that is not functioning properly.

Can a power stroke 6.0 liter diesel have a hard start?

When the FICM starts to fail, the 6.0L Power Stroke will have a hard start or no start issue, rough idle and loss of power. When replacing the FICM, 6.0 Complete FICM Part number: 4C3Z-12B599-ABRM, you must use the Ford IDS scan tool to remove the programing from the bad FICM and reprogram the new FICM and the PCM or get the Pre-Programmed FICM.

Are there any problems with a 6.0 liter diesel engine?

Below are the most common problems associated with the 6.0 Power Stroke engine. The 6.0L Power Stroke fuel injection system operates on oil pressure, very high oil pressure.

Are there any problems with the ISB 6.7 Cummins Engine?

A few of the most common faults on the ISB 6.7 liter Cummins turbodiesel engine include: Problems with the Cummins 6.7 often come down to emissions parts. However, the turbos and head gaskets are known to run into occasional failures too. It’s a good time to add a few notes that apply to this article.

Why does my international 4300 DT466 not start?

If theres any air in it at all, it wont start. . The daytime running lights (DRL) and low beam headlights are inoperable. The highbeam headlights, markers and all other lights function properly. I have checked the fusebox in the engine compartment and above the glovebox and am unable to locate either a DRL/headlight, fuse or relay.

Are there any engine problems with international engines?

In the 3 months I worked there, 4 trucks got replacement engines straight from Navistar because they were dropping injectors, snapping cranks, and having inj. pumps fail. International was shipping in new crate engines for these trucks, and telling us to send the old ones back to Navistar’s Research department.

What are some common problems with International trucks?

Most of the common repair complaints are prevalent in trucks of all sizes from International, which includes commercial vehicles, such as tow trucks, delivery trucks, roll trucks and refrigerated trucks. After 2004 these vehicles typically had the 6.0 liter diesel engine as the factory engine as well as the MaxxPro Star engine in larger trucks.

What kind of engine is in an international truck?

International was shipping in new crate engines for these trucks, and telling us to send the old ones back to Navistar’s Research department. BTW, all these engines were VT365’s, which was the same as Ford’s new 6.0 Powerstroke, and Ford bought back the first 500 trucks that were sold with that engine…

What is the repair manual for an international truck?

1986-2008 International Truck (ALL MODELS) Workshop Repair & Service Manual (2.6G DVD, Searchable, Printable)

What’s the model year of an international truck?

Complete digital workshop service and repair manual written for the International Truck (ALL MODELS); Production model years: 1986 1987 1988 1989 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008. All styles covered (all models, and engines).

When was the last international light truck made?

The D-Series was International’s last light truck and was discontinued in 1975. The Cargostar was a forward control cab-over-engine medium-duty series introduced in 1970. Replacing the cab-over-engine Loadstar models, the Cargostar had an improved cab and heavier models.

Where can I find the International Diagnostic Code?

International 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600 fault code list (PDF) – download The ability to display diagnostic trouble codes (DTC) is an optional feature. Codes may be displayed on either the gauge cluster or an optional vehicle information display (VID).

Where to find DT 466E trouble code list?

You can go to this site: https://evalue.internationaldelivers.com/service/bodybuilder/general/engine/eges270_FC.xml and click on the actual code (DTC) to access some decent diagnosis pages! Or scroll down for a quick reference. One word of *CAUTION* …

What is the trouble code for the International 4700?

97 International 4700 dt466e. Need trouble code info 97 international 4700 w/dt466e looking… Submitted: 9 years ago. Category: Medium and Heavy Trucks Experience: Over 16 years experience on medium and heavy duty trucks. Cyl. Contribution Test Failure – Cyl 1

What are the trouble codes for International trucks?