What are the airbag codes on a Chevy Chevorlet?

Call us at 888-779-9029 M-F 9-5 EST Review the GM Chevorlet airbag codes list below: RF/Passenger Frontal Deployment Loop (Stage 2) Resistance Low Passenger Airbag Module Deployment Circuit -Ckt Resistance Low (Stage 2)

Where is the airbag reset button on a Cadillac?

Right-hand Front Seat Belt Pretensioner High Circuit Voltage (12 volt VSS) & Seat Belt Pretensioner Deployment Circuit -Ckt Resistance Out Of Range Left-hand Front Seat Belt Pretensioner High Circuit & Seat Belt Pretensioner Deployment Circuit -Ckt Resistance Is Out Of Range

Can a Chevy airbag be reset by myairbags?

The best part of having your Chevy’s original airbag module reset by MyAirbags is that when you get your airbag control module back and it goes back into the same vehicle that it came out of then it will be plug-n-play. No additional programming of the VIN is required to fix your airbag codes.

Where are the deployment loops on a Chevrolet airbag?

Second Row Left Frontal Stage 1 Deployment Control (Subfault) Third Row Left Roof Rail Deployment Loop Resistance Above Threshold Third Row Left Roof Rail Deployment Loop Resistance Below Threshold Left-hand Side Impact Airbag Module Deployment Circuit -Short To Ground or Earth Or Voltage (12 volt VSS)

What is the DTC code for a airbag module?

Third Row Left Roof Rail Deployment Loop Resistance Above Threshold Third Row Left Roof Rail Deployment Loop Resistance Below Threshold Left-hand Side Impact Airbag Module Deployment Circuit -Short To Ground or Earth Or Voltage (12 volt VSS) Left-hand Side Impact Airbag Module Deployment Circuit -Short To Ground or Earth Or Voltage (12 volt VSS)

What does the b0013 code on a Chevy mean?

B0013 Chevrolet Meaning. If a malfunction is detected, a Diagnostic Trouble Code (DTC) will be stored in non-volatile memory. During a frontal crash of sufficient force the inflatable restraint Sensing and Diagnostic Module (SDM) will allow current to flow through the deployment loop in order to deploy the steering wheel module.

What is the trouble code for GM airbags?

GM has issued a service bulletin to address an airbag light on condition along with the following trouble codes: B0012, B0013, B0015, B0016, B0019, B0020, B0022, B0023, B0026, B0033, B0040, B0042 or B0044 on the vehicles listed below. 2006-2014 Chevrolet Corvette, Impala, Malibu Models (includes Malibu Classic)

Where are airbag codes stored in a Chevy?

Below you will find common airbag codes that can be stored in your airbag control module after your vehicle was in an accident. The best part of having your Chevy’s original airbag module reset by MyAirbags is that when you get your airbag control module back and it goes back into the same vehicle that it came out of then it will be plug-n-play.

What does the b0012 code on a Chevy mean?

Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the B0012 CHEVROLET code is 1.0 hour of labor.

How to fix code b0012 Chevrolet driver deployment loop?

How do I fix code B0012 CHEVROLET? Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. How much do you know about cars? What does this mean?

How much does it cost to diagnose a b0012 Chevrolet?

The cost of diagnosing the B0012 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. If a malfunction is detected, a Diagnostic Trouble Code (DTC) will be stored in non-volatile memory.

Do you clear trouble codes before resetting airbag light?

Do never clear the trouble codes before you fix the problem caused by the airbag light. Read the codes and get information about what can cause the problem and therefore continue the diagnosis. You should never just reset the airbag light without repairing the problem.

Why is my airbag light on code b0103?

There are numerous conditions that can set the B0103 code. Can be a short to ground in the circuit, high resistance in the circuit or the sensor or an open in the circuit or the sensor. Re: Airbag light is on code b0103 cannot locate it

How do you change the airbag light on a GM car?

Once you have repaired the terminals, apply dielectric grease GMP/N 12345579 on the connector pins and terminals when reassembling. Reassemble the connector ensuring you hear and feel an audible click. Then reinstall the CPA clip. Clear the airbag codes and check for airbag light on next IGN cycle.

What causes the airbag light to turn on?

If the CPA clip is missing or installed incorrectly, the system will set a trouble code and turn the airbag light on. Use the trouble codes to determine which connector is generating the fault. Then power down the airbag system before proceeding.

What is the front bumper airbag sensor code?

This is on my 05 Sierra 1/2 ton crew. Managed to locate a scanner that will show airbag codes, and it appears to be one of the 2 front bumper sensors (which I believe are mounted on the rad supports). The code read “front end sensor 2 fault”

Where is the airbag sensor on a Silverado?

The easiest way to find them is to look for the yellow and orange connector. You need to take the orange saftey clip out first, then take the yellow connector off. There is one bolt that goes through the center of the sensor. Take it out, and replace with new one. Real easy.

Why does my Chevy Silverado have a random missfire code?

Chevrolet Silverado 2500 B0103 Electronic Front end sensor… A random missfire code can be a number of things. Ignition related or fuel. The injectors clogging, vacuum leaks and such. There has been a service bulletin for the intake gaskets though.