Is the turn signal on my Dodge 1500 working?

I have a 2006 Dodge Ram 1500 with a Hemi. My right rear turn signal is not working. I have replaced the bulb and the socket and still nothing. light works when i press unlock on the keyless entry remote, but not for turn signal. front blinker blinks fast but no blinking at rear.

Can you replace the turn signal relay on a Ram 2500?

You can find and replace the turn signal relay in your Dodge Ram 2500 with a few common tools. You can do this job at home; it should take you less than 20 minutes to do.

What causes the turn signal to flash on a Dodge Ram?

Turn Signal problem of the 2006 Dodge Ram 2500 8 Failure Date: 10/13/2015 Turn signal will flash the opposite signal than the direction you desire. Example, turning on the left turn single will cause the right turn signal to flash, and vise versa, as well as causing the emergency signals to activate.

Are there any problems with Dodge Ram 2500?

Dodge Ram 2500 owners have reported 53 problems related to turn signal (under the exterior lighting category). The most recently reported issues are listed below. Started when using the turn signal (left) it makes the right turn on. . . . And now the right signal is failing to illuminate.

When does the turn signal go out on a Dodge Ram?

Discussion in ‘ Audio & Electronics ‘ started by Mcgruff, Jun 2, 2018 . i have a 2015 1500 with factory LED taillights. I recently had a low beam light go out. No big deal. Then it started telling me left rear turn out. Later that day, Right rear turn signal. Headlight was legit out. Replaced bulb, no more message.

You can find and replace the turn signal relay in your Dodge Ram 2500 with a few common tools. You can do this job at home; it should take you less than 20 minutes to do.

Why is my turn signal relay not working?

However, the most common cause of relay damage is attributable to an electrical fault in a relative location, such as the taillight assembly. You can find and replace the turn signal relay in your Dodge Ram 2500 with a few common tools. You can do this job at home; it should take you less than 20 minutes to do.

Can a tail light be replaced on a Dodge Ram?

The tiny LED’s can be replaced. It means you have to pull the tail lights apart, identify the failed LEDs, find LEDs of the same value, desolder and remove the failed LEDs and install the new ones by soldering them in.

How to diagnose lighting problems in a Dodge Ram?

Keep reading for a step-by-step guide for diagnosing various lighting problems in your Ram. It is possible that you may get a light out indicator on your instrument panel but can’t actually find the bulb which is out. Look again. Inspect all bulbs including brake lamps, turn signals, fog lights, license plate lights, etc.

Is the brake light on my Dodge Ram working?

This was a major update including an all new frame, suspension, powertrains, interiors, and sheet metal. I have a Dodge ram 1500 2007 yesterday my brakelights and turn signal stopped working I have changed the bulbs checked the fuses the tail lights work also the third llight is working front turn signals blinking fast.

Why are my brake lights and turn signals not working?

I have a Dodge ram 1500 2007 yesterday my brakelights and turn signal stopped working I have changed the bulbs checked the fuses the tail lights work also the third llight is working front turn signals blinking fast. Is this a good question? There’s most likely a short in the wiring at the rear of the vehicle.

How to change the turn signal on a Dodge Ram?

Refer to the inside sticker of the fuse box panel and locate the two flasher relays. Switch the relays, and check if the turn signal lights are flashing. If one or both of the relays fails to turn on the turn signal light, replace as needed.

Where are the flasher relays on a Dodge Ram?

Why does my car shudder when I Turn Left?

If the shudder is more pronounced in left turns, it is associated with a problem on the right front. If the shudder is more pronounced in the right turns, the problem is associated with the left front. The problem might exist in tires, tie rods, or other steering linkage components. Step 5: Inspect the front end.

Why does my car pull to the side when taking a turn?

Also, the front-end alignment is another important thing. Uneven wear on the front tires will make your car pull to a side while driving or taking a turn. Uneven tire tread leads to misalignment of the wheels, which can also a reason that triggers hard and stiff steering at the time of making turns on the road.

Is the blinker on my Dodge Ram still working?

Blinker still blinks erratically on occasion, but works most of the time. TIPM plugged right in with no other work necessary. did not flash the computer. 9 people found this helpful.

Are there any problems with the Dodge Shadow?

During the latter years of manufacturing Dodge Shadow units, Chrysler faced reports on a faulty front seat assembly. This was a common problem for the 1994 models that had attaching bolts prone to failing and detaching. The problematic bolts can be found at the lower-rear portion of the front seats.

When was the last Dodge Shadow car made?

The selection was based on on-road records from 1990 to 1992. The last Dodge Shadow unit was produced on March 11, 1994. The 1, 423, 068th car was delivered to Colonial Dodge in Kensington, Maryland. It was a two-door sedan that sported a 2.5-liter engine and a two-speed automatic transmission.

Why does my Dodge Shadow make a noise?

The Dodge Shadow, in particular, has recorded complaints on distracting noise originating from the engine and the shifter. The squeaks that come from the shifter are usually observed by models with manual transmissions. This is usually heard when the car shifts into or out of gear, indicating deeper problems with the shifter assembly.

Why does my turn signal not turn on?

If the turn signals are blinking fast, not blinking or turning on at all, the problem could lie in the flasher relays or the turn signal lever. Check the flasher relay: On the driver’s side of the cabin, between the dashboard and the door, you will find a small panel covering the fuse/relay box.

What should I do about my 2001 Dodge Dakota?

This 2001 Dodge Dakota came in with the complaints that the turn signals, stoplights and hazards lights all quit working. This repair will generally apply to 2001, 2002, 2003 and 2004 Dakota and Durango vehicles. Testing begins with checking fuse 19 in the interior fuse box and fuse 1 in the power distribution center under the hood.

Why does my Turn Signal Flash on my Dodge Ram?

The contact stated that the turn signal lights were defective and the right turn signal light would flash when the left turn signal was activated. The left turn signal would flash when the right turn signal was activated.

What to do when your turn signal is not working?

Step 2 – Locate the power distribution center (PDC) or fuse panel to check all system fuses. Learn more – To locate the fuse consult the owner’s manual or search Google Images. Step 3 – When a turn signal flasher or relay fails the blinkers will not operate or come “ON”, but not blink.

Why does my Dodge Ram 1500 not turn?

Sometimes it shows the opposite blinker on the instrument panel and sometimes it doesn’t show the blinker on at all. This happens in motion on a city street when changing lanes, in motion while turning, and stationary while waiting to turn. See all problems of the 2004 Dodge Ram 1500 .

Why is my low beam headlight not working on my Dodge Ram?

After replacing the driver’s side headlight bulb twice on our 2006 Dodge Ram 2500 SLT 4WD Cummins Diesel pickup, the low beam still wasn’t working. I swapped the known good bulb from the other side and the low beam was still out, even though the high beam and fog lights were all functional.

What are the front lights on a 2006 Dodge Ram?

To make the job harder on yourself, here are the 2006 Dodge Ram Front Lighting Wiring Diagrams. If you are so inclined, have at it. The only challenge I encountered was tracking down the correct wires at the wiring harness. The mechanic’s note read, “Jump the white and tan wire in black box to the white and green wire in blue box.”

What happens when you turn on the headlights?

When you turn on the headlights, the wires to the low beams return a signal to the ECM (Engine Control Module) which sends power to the lamps. Really? What brilliant engineer decided to remove an inexpensive relay from the circuit, requiring replacement of an $800± computer instead of a $20 bulb?

Are there any Dodge 1500 headlights left in stock?

Only 8 left in stock – order soon. . . Only 11 left in stock – order soon. . Only 3 left in stock – order soon. . Only 5 left in stock – order soon. . . . Only 5 left in stock – order soon. . . Only 4 left in stock – order soon. . Only 5 left in stock – order soon. . Only 4 left in stock – order soon.

Blinker still blinks erratically on occasion, but works most of the time. TIPM plugged right in with no other work necessary. did not flash the computer. 9 people found this helpful.

Why is the electric signal not getting to the socket?

The electric signal is not getting to the socket. The front bulb is blinking so everything is working. See what color wire is on the front bulb, find that color wire at the rear and trace it to the closest connector to see if that is getting the voltage. You have an open connection somewhere.

Why are my blinkers not working on my Dodge Ram?

I have a 2006 Dodge Ram 1500 2wd and recently started having flaky turn signal problems. They don’t work in the rear. After doing much reading online the general consensus was 90% of the time problems with blinkers were due to a bad faulty multi-function switch.

Is there a turn signal relay on a truck?

There is no turn signal relay on this truck. The Integrated Power Module (IPM) is a combination of the Power Distribution Center (PDC) (1) and the Front Control Module (FCM) (2). The PDC mates directly with the FCM to form the IPM.

What to do when your turn signal goes out?

all you have to do is reset (or get) the TIPM reset at a dealer or with a compatible scan tool. when a bulb burns out, the TIPM (central Gateway) shuts down that circuit to protect it, because it does not know what the problem is and is protecting itself. In other words it is a “CASH GRAB” for dealerships.

What causes light indicator to turn on on Dodge Ram?

Inspect the wiring and housing for all light bulb sockets in each light component. If you or the previous owner has installed “mismatch” bulbs, this could cause the indicator to turn on. Replace faulty bulbs if found and/or mismatched bulbs. Figure 1. “Lamp Out” light on dash.

Are there any problems with the Dodge Ram?

From bad fuses to bad grounds to a bad wire harness, we’ll move step-by-step through some solutions to these irritating problems. This article applies to the 2nd Generation Dodge Ram (1994-2001). Dodge Rams will occasionally have some light problems, especially on older models.

What are the most common issues with Dodge Ram Trucks?

The more common body issues on Dodge Ram trucks include: 1 Rotting of the outer wheelhouse and upper wheel arch area of the bed. 2 Rotting of both driver and passenger side cab corners. 3 Rotting of both driver and passenger side rocker panels, typically starting across the lower door weatherstrip seal. 4 Rotting of the oil pain.

Why is my Dodge Ram 1500 not shifting?

The transmission may also slip or refuse to shift at all, which is one of the main 2006 Dodge Ram 1500 transmission shifting problems. Sometimes switching out the solenoids can fix the problem for around $50 to $100 plus labor if you have it done by a shop.

What causes a Dodge Ram truck to stall?

If your 2011 or other RAM in this model year range stalls when stopping, stalls at idle, or seizes up unexpectedly, you may have one of the most commonly reported problems for these trucks — cam and lifter failure. This issue can potentially affect all late models.

Why is my turn signal not working on my Dodge Caravan?

If the turn signal (also known as a blinker or flasher) blinks rapidly or doesn’t blink at all / stays stuck when engaged, this is your Caravan’s way of telling you that a turn signal bulb is burnt out.

Why are my left and right turn signals not working?

Replace any bulbs that are not lit. The flasher unit is used to switch the current on and off for both right and left directionals. If the turn signals are inoperative in both directions, a defective flasher unit or blown fuse is the usual cause.

How can I diagnose a turn signal problem?

Diagnose Turn Signal Problems. The flasher contains what’s known as a “bi-metallic spring,” which is a flat strip with one kind of metal on one side, and another kind on the other. The flexible strip connects the electrical supply from the box to the wiring that goes to your turn signal switch.

What to do when turn indicators don’t flash?

Turn Indicators on Dash Don’t Flash 1 First, check that your turn lights work properly. 2 If one of the signal lights doesn’t come on, check the bulb; check the bulb socket for corrosion or damage; check for a bad ground at the socket. 3 Check for an open in the circuit, between the light (s) that doesn’t work and the turn signal switch.

Is there a problem with the turn signal on a Dodge Ram 2500?

The contact owns a 2003 Dodge Ram 2500. The contact stated that the left and right turn signals have failed to function normally. Whenever the left signal was turned on the right one would come on and vice versa for the right signal. The vehicle was not taken to the dealer.

Is the turn signal on my Dodge 2500 inoperable?

Tl-the contact owns a 2006 Dodge Ram 2500. The contact stated that the passenger’s side turn signal and brake light became inoperable. The vehicle was taken to a dealer where it was diagnosed that the power module needed to be replaced. The vehicle was not repaired.

Where are the turn signal relays on a Dodge Ram?

Check the flasher relay: On the driver’s side of the cabin, between the dashboard and the door, you will find a small panel covering the fuse/relay box. Refer to the inside sticker of the fuse box panel and locate the two flasher relays. Switch the relays, and check if the turn signal lights are flashing.

Where is the brake light switch on a Dodge Ram?

Dodge Ram turn signal lever. The brake light switch can wear out, which translates into no brake lights on your Dodge Ram. If the bulbs as well as the connections are good and the wires are properly grounded, replace the switch. You will find it under the brake pedal. Figure 4. Brake light switch.

What does the fuse box do on a Dodge Ram?

The fuse box helps provide reliable power at the proper amperage to various electrical components on your Dodge Ram. These include lights (running lights, back-up lights, headlights), heater, A/C, and power locks. This part, also known as a Power Distribution Center (PDC), can have problems on the Dodge Ram.

What are the problems with a 2002 Dodge Ram 1500?

Lighting issues are common in Dodge Ram trucks and are one of the most frequently-cited 2002 Dodge Ram 1500 electrical problems specifically. Owners find that their headlights, taillights or turn signals suddenly stop working, causing irritation at best and a safety hazard at worst.

Where are the rear lights on a Dodge Ram?

For example, if you are having rear light problems, first check the wire harness supplying the signal and power to the rear lights, which is the harness located behind the wheel well on the driver’s side of the truck. If you look near the bottom of the wheel well, you will see a small panel; behind that panel is the wire harness.

Can a burnt out turn signal be replaced?

This video shows you how to replace a burnt out rear turn signal on your 2012 Ram 1500. We recommend that you change both the driver and passenger side bulbs at the same time on your 1500 as they get dimmer over time and if one is out, then the other one is likely to burn out soon.

How much is a rear turn signal bulb from Advance Auto Parts?

Advance Auto Parts has 1 different Rear Turn Signal Bulb for your vehicle, ready for shipping or in-store pick up. The best part is, our Dodge Ram 1500 Rear Turn Signal Bulb products start from as little as $10.99. When it comes to your Dodge Ram 1500, you want parts and products from only trusted brands.

What kind of turn signal bulb do I need for Dodge Ram 1500?

When it comes to your Dodge Ram 1500, you want parts and products from only trusted brands. Here at Advance Auto Parts, we work with only top reliable Rear Turn Signal Bulb product and part brands so you can shop with complete confidence. Some of our top Rear Turn Signal Bulb product brands are Sylvania.

Where are the tail lights on a Dodge Ram?

Pick up the input feeds from the Dodge Ram tail lights in the wiring harness then splice the output signals into the trailer’s tow connector. Click here to check out information about Modulite 119190 units.

How can I test the lights on my Dodge Ram?

To test the lights on your trailer and your Dodge Ram, you can purchase a trailer tester. Click here to check out trailer testers. Figure 1. Testing the trailer lights. If your trailer lights are still not working, proceed to Step 2.

Why are the tail lights on my Dodge Ram not working?

Not open for further replies. I need some help here. I have a 2003 Dodge Ram 1500, and the Tail Lights just stopped working. The Break Lights, Turn Signals, Reverse Lights all work, but the Rear Parking Lights and License Plate Light isn’t working at all…

Why are there no brake lights on my Dodge Ram?

The brake light switch can wear out, which translates into no brake lights on your Dodge Ram. If the bulbs as well as the connections are good and the wires are properly grounded, replace the switch. You will find it under the brake pedal.

Why are the lights on my Turn signal not working?

While they may still light up, the lights will not be able to serve their intended purpose of signaling a turn or emergency situation. These same symptoms can also be caused by electrical issues, so having the vehicle properly diagnosed is highly recommended. 3. Additional lights are not working

Why does my Dodge Ram 1500 not start?

I have a 1999 Dodge Ram 1500, with the factory security system (no remote start) and the horn honks continuously no matter if the truck is running or not. So I bought a new Horn Relay thinking that was probably the problem and replaced it, but it still didn’t fix it.

What are the symptoms of a bad turn signal Flasher?

1. Turn signals or hazards do not function. The most common symptom of a bad or failing turn signal / hazard flasher is hazards or turn signal lights that do not function. If the flasher breaks or has any internal issues it can cause the lights to malfunction, or not respond at all when the turn signal lever or hazard light button are pressed.

Why is my turn signal not working on my Dodge Ram 1500?

Why is the turn signal blinking so fast?

2006 dodge ram 1500 3.7 liter left blinker is blinking fast and the driver front and back blinker is not working or flashing. got a new blinker switch but still does the same thing…help 13 people found this helpful. As I recall too heavy of a load will cause the turn signal lights to blink fast.

What causes a ticking sound in a Dodge Ram 1500?

A bad or failing manifold leads to decreased engine performance, and broken manifold bolts are common in Dodge Ram 1500s of all ages. The most common symptom of broken or degraded bolts is a ticking sound on cold starts, frequently heard from the passenger side of the truck.

Why are my turn signals and brake lights not working?

– CarGurus rear turn signals and brake lights don’t work. no power in yellow wire all the way to the firewall. everything under dash works right, looks right, indicator lights work and front lights work fine. No they don’t. 13 people found this helpful. Thank you so much! It was broken wires in the steering column.

Is the turn signal on my Dodge Ram working?

Hazard lights which use same bulb also work. just no turn signal. have already replaced the multifunction switch through the dealer because of factory recall. The electric signal is not getting to the socket. The front bulb is blinking so everything is working.

How to know if your Dodge Ram has transmission issues?

There are a variety of ways transmission issues show up in these trucks, including: 1 Slow starts. 2 Engine running rough. 3 Bumping hard into 1st gear. 4 Jerk when shifting from 1st to 2nd. 5 Slipping into gear when in traffic. 6 Hard downshift to stop when slowing down.

Is there an error on my Dodge Ram?

An error occurred. Please try again later. (Playback ID: QW-h1Whvs0g93DfG) Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.

What are the warning lights on a ram?

The following are warning lights and indicators found in vehicles built by Ram. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are over 70 of them so be patient!

How does the oil change indicator work on a ram?

Some Ram models have a percentage-based indicator that counts down the oil life as a percentage. Once the information display number reduces from 100% (fresh oil) to 15% (dirty oil), an “OIL CHANGE REQUIRED” light will be trigged on the dashboard information display, giving you ample time to plan ahead to have your vehicle serviced.

What do you need to know about Dodge Ram tail lights?

Use the form above to tell us what you drive. The Dodge Ram tail light assembly houses your truck’s rear, brake and reverse lights, along with your back turn signals. If it becomes cracked or faded, your lights dim and it is more difficult for other drivers to see you when it’s dark or the weather is bad.

Why is my turn signal not working on my Dodge Ram?

How to change the blinker light on a Dodge Ram?

This is a step by step instruction on how to change the sidemarker blinker bulb on your dodge vehicle. A 2003 RAM 2500 is shown, but other Chrysler vehicle may be similar. The light bulb called for is the 4157NA, also known as the 3157NA, the only difference is that the 4157 has a longer life. The NA denoted an orange colored lightbulb. Loading…

Where is the turn signal on my Dodge Ram 1500?

I traced the wire (yellow for left rear signal on GM) that feeds the lamp with a test light back until I had voltage. It turns out the wire burned off above the driver’s seat where the wire passes above the door in the channel probably from a screw for the headliner.

What’s the problem with the turn signal on a Dodge Ram 1500?

Turn Signal problem of the 2004 Dodge Ram 1500 2 Failure Date: 02/27/2016 The turn signals will show reversed so when you turn on the left blinker, the right blinker will blink and vise-versa, or sometimes the blinkers will not engage at all.

Is there a problem with my Turn signal?

Intermittent turn signal failure. Turn left signal on, and flash then right signal will occasionally flash. Sometimes left and right will alternate. This is not the same as emergency flashers where both lights are on at the same time.

How to change the front turn signal Ram?

Front Turn Signal Change Ram 1500 (2011-2018) 1. Getting Started – Prepare for the repair Learn More > 2. Open the Hood – How to pop the hood and prop it open 3. Remove Bulb – Steps to remove a burnt out bulb 4. Helpful Hints – How to find replacement bulb type and other hints 5. Replace Bulb – Procedures to replace the new bulb 6. More Info.

What should I do if my Dodge Ram won’t turn on?

If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. Cars, Trucks, and anything that goes fast is our passion!

What is the displacement of a 2006 Hemi?

The engine has a bore (cylinder width) of 3.92 inches, a stroke (distance piston travels inside the cylinder) of 3.58 inches and a 9.6-to-1 compression ratio. The 2006 HEMI has a displacement of 5,654 cubic centimeters. The output of the 5.7-liter HEMI is measured by its torque and horsepower rating.

What kind of car is the 5.7 Hemi?

In the 2006 model year, seven Chrysler vehicles use the 5.7 HEMI: the Dodge Ram 1500, 2500 and 3500; Dodge Durango, Dodge Charger, Dodge Magnum and Chrysler 300 C.

What’s the horsepower of a 2006 Chrysler Hemi?

The output of the 5.7-liter HEMI is measured by its torque and horsepower rating. This engine has multiple output ratings, as Chrysler uses it in several vehicles. In the 2006 Ram 1500 and 2500, the HEMI produces 345 horsepower at 5,400 rpm and 375 ft.-lb. of torque at 4,200 rpm.

What’s the horsepower of a 2006 Ram 1500?

In the 2006 Ram 1500 and 2500, the HEMI produces 345 horsepower at 5,400 rpm and 375 ft.-lb. of torque at 4,200 rpm.

Why is my Dodge Ram transmission not working?

No heat One of the leading causes for Dodge Ram transmission problems can be a heat a problem. But why is it? If the coolant has some dirt residue—all the dirt will eventually stop the flow of the coolant. While this is not a permanent fix, this will allow you to drive for quite some time.

Why is my Dodge Ram 1500 no start?

Please try again later. This 2004 4.7l Dodge Ram 1500 had an intermittant no crank/no start. Instrument cluster self test revealed no communication with the PCM. Wiggling the wires at the Integrated power module and PCM seemed to help but eventually it refused to crank at all. Problem was traced back to a worn through PCM B+ wire.

How to reset the Check Engine light on a Dodge Ram?

Dodge Ram: How to Reset PCM and Check Engine Light. 1 Step 1 – Remove the PCM fuse. First, park your truck and turn it off. Pull the hood lever under the driver’s side dash, and then pull the safety catch 2 Step 2 – Reset the PCM. 3 Step 3 – Re-install the PCM fuse. 4 Related Discussions.

How to solve color code wiring Dodge Ram?

An expert that got 20 achievements. An expert that got 10 achievements. We do nmot have wiring disgrams but do this, buy a $3 12 vgolts test light from Autozopne and as a helper operates all the light functions probe the wiring at the connector as the wire lights up the test light make a note of wha that wire runs and move on.

Can a tail light be connected to a left turn signal?

Thinking fast, I removed the opposite tail light assembly and connected it to the left side connector I had removed. The left turn signal worked fine when connected to the right tail light. Problem solved! Almost. I was very grateful the tail light wiring issue was not somewhere in the truck.

After dealing with mysterious engine trouble codes and then just a week later replacing the driver squib on our Dodge Ram, I nearly screamed when Rene came home at dusk one evening and immediately got out to run around the ruck and check all the lights. (I know better to laugh instead .)

Where is the turn signal bulb on a Dodge Ram 2500?

The front turn signal bulb on the 2005 Dodge Ram 2500 is located in the headlight assembly. The bulb, number 3157A, is an amber dual-filament bulb and is available from the Dodge dealer, an auto parts store or even some department stores.

Why is my right rear turn signal not working?

Right, Rear Turn Signal Not Working but its a New Bulb to… Okay, I recently replaced my rear turn signal bulbs just a couple months back. Just recently, the right rear blinker indicator has been blinking really fast. Sometimes it would blink fast and sometimes it would blink normally. Today I checked the right rear blinker and it would not work.

Why is my left turn signal light not flashing?

Operate the switch to turn the left turn signal light. Back probe the wire that supplies power to the switch; the test light should flash. If the test light doesn’t flash, there is a problem with the flasher unit or an open or short between the switch and the battery power source.

What to do if rear turn light is not working?

If you get a small strip of 400 grit sandpaper and rub it on the contact surfaces in the bulb socket, that will probably get you working. If that doesn’t do the trick, you have to get a test light or a meter and go hunting for the interruption.

How to troubleshoot the turn signal light on a Dodge Caravan?

Turn on the turn signal to blink on the side of the Caravan you would like to troubleshoot. Look at the indicator light on the instrument panel to see if it is blinking very quickly. If it is blinking quickly you have a taillight out. If it is blinking at its normal rate or not blinding at all, go on to Step 2. Look to see if you have a blown fuse.

Why is the rear blinker not working on my car?

I replaced the bulb with a brand new bulb and still it would not work. The left blinker and tail light work fine. The right tail light works fine. Its just the right, rear blinker.

Is the turn signal on my Dodge 1500 working?