How to replace a valve seal on a Bobcat loader?

Lubricate the valve spool, then gently slip a new seal onto the spool, working it to the centering spring end of the spool. Take your time and be patient, being careful as your working the seal over the sharp edges along the spool.

Why is my Bobcat loader control valve oily?

Occasionally a member finds their Bobcat loader control valve making an oily mess of the bottom of their machine because it needs new seals for the control valve spools.

What’s the difference between a 743 and 743 wheel loader?

There may be differences on older models, such as a 743, but the differences have little affect on the procedures for doing this repair. On the wheel loaders, it’s a little easier because you can remove a side plate to access the front of the control valve easy.

Who is responsible for fitment of a bobcat?

If you choose not to verify fitment, you resume full responsibility for fitment issues. This does not fit your machine. By adding this item to your cart you resume full responsibility for fitment issues.

What is the serial number for the bobcat 743?

Stop Spring (F& C Series) This is Spring Only Fits Models: 730 731 732 741 742 743 751 753 763 7753 773. Before you purchase this, email us your serial number and we will let you know if this will fit your machine.

Occasionally a member finds their Bobcat loader control valve making an oily mess of the bottom of their machine because it needs new seals for the control valve spools.

What kind of pipe does a bobcat 643 use?

2 inch bolt pattern 1.74 inch pipe-see pics. It fits the following models: 643. 645, 653, 743. Before you purchase this. Email me your serial number and I will let you know if this will fit your Bobcat. This is pick up or can be shipped usps priority. If you have any questions email. Or call me at 309-635-3346.

When to replace an oil seal with a new seal?

Choose an oil seal in the proper size and replace the original seal. The outer diameter of the oil seal is smaller than the internal diameter of the bore. Excess pressure is displacing the oil seal axially. Choose an oil seal in the proper size and replace the original seal. The internal diameter of the bore is too small.

How do you replace a seal on a washing machine?

Categories: Washing Machine Repairs. Article Summary X. To replace a washing machine door seal, first pry off the door’s outside rubber band. Then, loosen the screw or nut holding the seal in place, and pull off the old seal.

What’s the best way to install an oil seal?

Applying a lubricant to the shaft will help the seal to bed in. Lubricating the bore will also make installation easier. The outer diameter of the oil seal is smaller than the internal diameter of the bore. Choose an oil seal in the proper size and replace the original seal.

Why is Bobcat 753 left steer control not working?

Re: Bobcat 753 – left steer control is not working at… Testimonial: “Thanks Bill ,have removed and checked the two check valves that are on top of pump and no sign of wear or damage .Would the next option be to pull motor out to get to the two release valves underneath .?” You can’t post conmments that contain an email address.

Why does my Bobcat Run but won’t move?

The lights all work in the control box and then after a few minutes the valve light starts flickering and the arm\bucket doesn’t move unless i restart the machine. Then sometimes the traction light will go off after the valve light does. The red 10 fuse blew a few times. Thoughts? Hi. New to site so sorry if I make a mistake. I own a 453 F series.

Can a Bobcat loader be repaired at home?

Some simply take the machine to their local Bobcat dealer for repair, but others consider doing the repair themselves and save a little money, to which they ask if this is a job that they can do. If one has a bit of mechanical skills, it certainly is a project that can be done. Here are the basic steps to accomplish the repair.

Where is the hole in a Bobcat loader?

At the rear of that compartment is a hole in the belly of the machine. Place an oil drain pan under the hole to contain the oil that will drain from control valve while making repairs. Track machines have the hole in a different location.

Where to find Bobcat equipment hydraulic valves for sale?

Quickly jump to this search by going to My Account and Saved Searches. Your new listings email alert for Bobcat Equipment Hydraulic Valves For Sale has been created. To change the email frequency or to modify your alerts, click on My Account, Personal Settings, and New Listing Alerts.

What is hydraulic solenoid on bobcat 773 C series?

I believe that my 773 C series with advanced hand controls has a BICS controller with the traction control solenoid (drops the bar to stop movement of the machine) and hydraulic solenoid valve. It also has two auxiliary electric solenoids on the control valve.

Is there a rebuilt version of the bobcat 773?

Rebuilt Bobcat 773 is available. If you worry about the condition of your decades-old equipment, you can buy a rebuilt model. A rebuilt model is made from used components with reasonable quality to ensure that the final product is the best of all used equipment. Some rebuilt models even come with a warranty.

What is the BICS lock solenoid valve on a bobcat?

If your machine is Advanced Hand Controls then the main control valve should have the BICS lock solenoid valve on the main control valve.

Is the valve on a bobcat C series?

Our bobcat is a C series. On the BICS its called the valve. The valve the seat bar and system activated lights on the BICS are not lit up either. As for the seat switch its never been connected and was running fine before hand.

How to replace a valve seal on a Bobcat loader?