How to remove camshaft sensor from Ford Ranger?

Step 1. Remove belts if still on engine. Step 2. If not already un-installed, loosen and remove hold down clamp before removing Old plug or broken/malfunctioning cam-synchro. Step 3. Remove valve cover Step 4.

Where is the camshaft sensor located on a Ford 3.0L engine?

On 3.0L engines, install camshaft synchronizer so that drive gear engagement occurs when arrow on Syncro Positioning Tool T95T-12200-A is pointed approximately 75 degrees (3.0L), 60 degrees (4.0L) counterclockwise off the centerline of the engine. This step will locate camshaft position sensor electrical connector to the original position.

How do you remove a cam positioning sensor?

Disconnect the electrical connector on the sensor by simply pulling it off. Remove the 10mm bolt in the bracket on top of the sensor securing it to the block. Twist the bracket and lift the sensor out of the block. Install the sensor and secure it in reverse order of removal. When the cam positioning sensor goes bad, it sets a code.

How is the Camshaft Position Sensor ( CMP ) used?

The camshaft position sensor (CMP) is used by the powertrain control module (PCM) to determine the position of the camshaft in relation to the crankshaft.

How do you change the camshaft position sensor?

1. Disconnect battery ground cable (14301). 2. Disconnect fuel charging wiring electrical connector from camshaft position sensor. 3. Remove the CMP sensor screws and camshaft position sensor from camshaft synchronizer. CAUTION: Do not move crankshaft (6303) until entire installation procedure is complete.

How to remove the camshaft synchronizer on a Ford Ranger?

It will show the location of the camshaft synchronizer, the removal process, and the installation. Note, before removing the camshaft synchronizer, make sure you mark the location of the housing and tab with a magic marker to ensure the replacement camshaft synchronizer goes in exactly the same way. Loading…

How does camshaft synchronizer work on a Ford 3.0L engine?

Armature tab will be damaged and synchronizer timing may be shifted. On 3.0L engines, install camshaft synchronizer so that drive gear engagement occurs when arrow on Syncro Positioning Tool T95T-12200-A is pointed approximately 75 degrees (3.0L), 60 degrees (4.0L) counterclockwise off the centerline of the engine.

Where does the camshaft position sensor send the information?

The camshaft position sensor gathers information about the vehicle’s camshaft speed and sends it to the vehicle’s engine control module (ECM).

Can a bad camshaft sensor shut down an engine?

Without this information, the engine would not be able to function properly. Over time, the camshaft position sensor can fail, or become worn down, due to accidents or normal wear and tear. There are a few warning signs to watch out for before your camshaft position sensor completely fails and shuts down the engine, making replacement a necessity.

What does the ECT sensor on a Ford Ranger do?

– is controlled by the PCM. The ECT sensor (4.0L): – sends the PCM a signal indicating engine coolant temperature. – resistance decreases as coolant temperature increases. The CHT sensor (2.3L): – sends the PCM a signal indicating cylinder head temperature.

How does the camshaft sensor work on a Ford Ranger?

Step 4. Using 1/2″ breaker bar, turn engine clockwise using the big crankshaft pulley bolt. bring engine cylinder #1 to TDC compression stroke (when both valves are closed). The #1 cylinder is the one closest to the front passenger side. Step 5.

What happens when the camshaft position sensor does not work?

3. Vehicle will not start The camshaft position sensor gathers information about the vehicle’s camshaft speed and sends it to the vehicle’s engine control module (ECM). The ECM uses this data to determine the timing of the ignition, as well as the timing of the fuel injection that the engine requires.

Who is responsible for damage to Ford Ranger?

Disclaimer: The Ranger Station.com, The Ranger Station.com Staff, nor the original poster are responsible for you doing this modification to your vehicle. By doing this modification and following this how-to you, the installer, take full responsibility if anything is damaged or messed up.

How to replace a bad camshaft position sensor in your car?

How to replace a bad camshaft position sensor in your car, DIY with Scotty Kilmer. They often go bad and turn your check engine light on and Code P0340. DIY car repair with Scotty Kilmer, an auto mechanic for the last 49 years. 1. Actron Scan Tool: http://amzn.to/2jxoUXq 2. Telescopic Magnet Pick Up: http://amzn.to/2jyDRZm 3. Common Sense 5.

How does the camshaft sensor work on a Ford F150?

by Cayden Conor. The camshaft sensor on a Ford F150 with the 4.2-liter V6 engine has a single hall-effect magnetic switch. A camshaft-driven vane triggers the switch. The sensor sends a signal to the engine’s computer (the PCM), telling the computer what position the camshaft is in relative to top dead center.

Where is the cam position sensor on a Ford 4.0?

by Don Bowman. The cam position sensor on a Ford 4.0 V6 is located on the dipstick side of the engine in the forward part of the block. The computer uses the camshaft sensor to determine the firing of the fuel injectors at the appropriate valve timing.

How to replace crankshaft position sensor 98-11 4-0l V6?

If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: XHeM17uym2G3EtsT)

How to remove camshaft sensor from Ford Ranger?