How much torque does a 4WD axle nut have?
How much torque does a 4WD axle nut have?
Tighten to 111 ft-lbs/150 Nm. Loosen 45° then retighten to 199 ft-lbs/270 Nm. 4WD 1980-1991 With manual locking hubs: Tighten adjusting nut to 50 ft-lbs/68 Nm while turning hub. Back off and retighten to 50 ft-lbs/68 Nm. Back off to 0. Install ring and tighten locknut to 160 ft-lbs/217 Nm minimum. Tang on ring must press through slot on spindle.
How to tighten the nut on a spindle?
How to tighten spindle nut ? The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn.
What kind of nut does a wheel spindle use?
If the spindle uses a castle nut and cotter pin or tang nut, tighten the nut finger tight until it stops, then back it off so the cotter pin or washer tang fits into the next indentation of the castle nut.
How big is the axle nut on a Cadillac?
Tang on ring must press through slot on spindle. Hole in pin must align with locknut. Turn adjusting nut to align. Endplay should be .001- .010″. With automatic locking hubs tighten adjusting nut to 50 ft-lbs/68 Nm while turning hub.
Tighten to 111 ft-lbs/150 Nm. Loosen 45° then retighten to 199 ft-lbs/270 Nm. 4WD 1980-1991 With manual locking hubs: Tighten adjusting nut to 50 ft-lbs/68 Nm while turning hub. Back off and retighten to 50 ft-lbs/68 Nm. Back off to 0. Install ring and tighten locknut to 160 ft-lbs/217 Nm minimum. Tang on ring must press through slot on spindle.
How big is the axle nut on a Chevy Malibu?
2013-2017 Tighten in three steps: First, 111 ft-lbs/150 Nm; second, loosen 45 degrees; last, tighten 185 ft-lbs/250 Nm. Malibu Limited 2016 Tighten to 111 ft-lbs/150 Nm. Back off 45 degrees and retighten to 184 ft-lbs/250 Nm. 2013-2015 177/240-ft/lbs/Nm Use new original equipment nut.
How big is the axle nut on a Chevrolet Acadia?
Make and Model > Chevrolet > Acadia > Chevrolet Axle Nut Torque… AWD 2007-2016 FRONT 173/235-ft/lbs/Nm REAR 151/205-ft/lbs/Nm 2017 FRONT AND REAR Use new nut. Tighten to 111 ft-lbs/150 Nm. Loosen 45° then retighten to 199 ft-lbs/270 Nm. 2017 Use new nut. Tighten to 111 ft-lbs/150 Nm. Loosen 45° then retighten to 199 ft-lbs/270 Nm.
Where are Dorman front wheel hub bolts made?
These wheel hub bolts directly replace the original bolts on certain vehicle years, makes and models. Dorman is a leading auto parts manufacturer founded in the United States and headquartered in Colmar, Pennsylvania. Our story began with the first mass market automobile.
2013-2017 Tighten in three steps: First, 111 ft-lbs/150 Nm; second, loosen 45 degrees; last, tighten 185 ft-lbs/250 Nm. Malibu Limited 2016 Tighten to 111 ft-lbs/150 Nm. Back off 45 degrees and retighten to 184 ft-lbs/250 Nm. 2013-2015 177/240-ft/lbs/Nm Use new original equipment nut.
Make and Model > Chevrolet > Acadia > Chevrolet Axle Nut Torque… AWD 2007-2016 FRONT 173/235-ft/lbs/Nm REAR 151/205-ft/lbs/Nm 2017 FRONT AND REAR Use new nut. Tighten to 111 ft-lbs/150 Nm. Loosen 45° then retighten to 199 ft-lbs/270 Nm. 2017 Use new nut. Tighten to 111 ft-lbs/150 Nm. Loosen 45° then retighten to 199 ft-lbs/270 Nm.
How big of a torque nut do I Need?
Tighten to 8 ft-lbs (10 N-m), then tighten an additional 1/3 turn to at least 37 ft-lbs (50 N-M). Upon initial installation of replacement ball joint, tighten nut to to 81 ft-lbs (110 N-m). 2. Tighten to 8 ft-lbs (10 N-m), then tighten an additional 1/3 turn to at least 48 ft-lbs (65 N-m). 3.
What are torque specs for Chevy wheel lug nut?
For 2019 and 2020 Chevrolet wheel bolt torque specs updates, please scroll to the last two rows at the bottom of the table below . When removing and installing a wheel on your vehicle, always follow these generic instructions, but for more information please refer to your owner’s manual.
What should the torque settings be on a Chevrolet wheel?
If you are planning on installing a wheel on your Chevrolet vehicle, it is important to be aware of the manufacturer’s recommended torque settings.
Where can I find the torque specification guide?
Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer. It is important that you properly torque the spindle nut to ensure optimum bearing life. Under torque of an axle nut will allow excessive movement causing uneven loading and excessive wear.
What happens if your spindle nut is over torque?
It will also leave your spindle nut under or over torque resulting in hub assembly failure. Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer. It is important that you properly torque the spindle nut to ensure optimum bearing life.
