How much does a 1995 Caterpillar 3406E engine cost?

3406E Reman Engine, 550 HP. New Cylinder Packs, New Bearings, New Head, New Injectors, New Oil Pump, New Water Pump, New Air Compressor, New Fuel Pump, New Turbo. Comes with a 1 year warranty. See More Details 1995 CAT 3406E 5EK Diesel Engine. 355HP, Approx. 419K Miles. All Complete. $8,995.00 with Exchange.

How big is a Cat C13 ACERT engine?

2008 Sterling L9500 T/A Tank Truck Cat C13 Acert engine, 430 H.P., Engine brake, 18 speed Eaton transmission, Air ride cab, Airline air ride suspension, 16000 lb front axle, 46000 lb rear axles, 218” W.G.,

Where can I find a 2005 Caterpillar 730 articulated rock truck?

2005 Caterpillar 730 Articulated Rock Truck- located in Southern Alberta Area, call for exact location -• 13,006 hours• Cat C13 engine• 367 hp• 52,690lb empty operating weight• 114,420lb loaded operating weight• Contact us today if you need more information.

How many miles does a 1999 Sterling truck have?

What kind of engine does 1999 Sterling have?

1999 STERING L9513 METER READS 471192 MILES 21,619 HOURS 8 SPEED EATON FULLER CAT POWERED CHELSEA PTO BEAU-ROC DUMP BODY 14FT STEEL 95% RUBBER ENGINE BRAKE LOCKING DIFFERENTIAL STEEL WHEELS RADIO HEAT/ AC DBL FRA…

How much does a 1999 Sterling water truck cost?

Priced to move, this 1999 STERLING 4,000 GALLON T/A WATER TRUCK WATER TRUCK- ON ROAD is for sale at a reduced price of $ 35000 with 15017 hours. Newman Tractor has been selling WATER TRUCK- ON ROAD s since 1976….

How often do Cat injector seals go bad?

How many of you truck owners out there, with C15 / C16 / 3406E engines, have replaced the injector seals, only to have them go bad again within 50,000 miles? It is a real problem with those engines, especially with Cat re-manufactured heads. I have a permanent repair for the problem. Contact me with any questions.

Can a cat injector not hold down properly?

Granted, it wasn’t a Cat, but it CAN happen. If the injector hold down bolts are stretched, the injector can’t seat properly, and combustion gas can get to the o-rings. Even had an instance where an injector wasn’t seated properly, and combustion gas pressurized the fuel tank, via the fuel return.

What causes an injector tube to break in a car?

Injector tubes do not involve fuel. The injectors bouncing on the seat in the head, wear into the seat which breaks the seal between the injector and the seat. This allows compression to get up to the o-ring which causes them to deteriorate. There is no known repair of the seat.I can now recut those seats.

Why does my Caterpillar 3406E break at Journal 1?

In the 3406Es with a 5EK engine serial number, there was a pretty bad and widespread crankshaft breakage problem. Some 5EKs were made from a bad casting, causing the crankshaft to break most commonly at journals 1 and 6.

Is the 3406E engine the same as the C15?

It was replaced by the C15, which was similar in parts and horsepower. You will often see, including on our website, that the same part will fit the 3406E, C15, and C15 ACERT. You should still always be careful when ordering parts, however, and make sure that you get parts with the correct part number.

Where can I buy a 1995 cat 3406E engine?

1995 CAT 3406E used diesel engine for sale . 355 HP, tested and inspected with warranty. Call or visit our website for more info. USED 3406E CATERPILLAR ENGINE WITH 475 HP, JAKE BRAKE (ENGINE BRAKE), 40 PINS ECM COMPUTER, YEAR:1.995-1.996, COMPLETE, INSPECTED AND TESTED RUNNING ENGINE, ALSO MANY ENGINES IN STOCK. – FOR PRICE See More Details

What’s the difference between a caterpillar C25 and a 3406E?

The Primary Differences Between Caterpillar 3406E, C15, and C15 ACERT Diesel Engines. 1 Caterpillar 3406E. The Caterpillar 3406E has been known as a reliable diesel engine throughout the years. Many mechanics praise this engine as being 2 Caterpillar C15. 3 Caterpillar C15 ACERT.

Are there any oil leaks in the Caterpillar 3406E?

However, as with all engines, there are usually a few issues that are well known. You may have heard of oil leaks with the 3406E. A common spot for leaks is near the rear side of the engine around the spacer plate and the cylinder block. During the production of the 3406E, Caterpillar wasn’t using the best gaskets.