Can a brake line rupture on a GM Truck?
Can a brake line rupture on a GM Truck?
Adler said that since the front and rear brakes are on different lines, drivers should be able to stop even if one of the lines ruptures. “GM does not see the rusty brake lines as a threat to safety because the brakes will stop the trucks,” he told ConsumerAffairs.
Why did my Silverado lose its brake line?
Nicholas of King of Prussia, Pa., said his 2000 Silverado 1500 lost its brakes at 27,462 miles due to excessive brake line corrosion. “Frame, brake lines, brackets, and suspension components were found to have systemic, abnormally high levels of corrosion,” he said.
What kind of brake line does Chevy Avalanche have?
Or, as Dennis of Murrysville, Pa., put it: “2002 Chevy Avalanche – While driving home from a 350-mile trip, my brakes failed due to a rusted brake line. Fortunately, people got the hell out of my way or I could have run over or into other vehicles with kids in them.
Can a rusty brake line stop a truck?
“GM does not see the rusty brake lines as a threat to safety because the brakes will stop the trucks,” he told ConsumerAffairs. The National Highway Traffic Safety Administration (NHTSA) has been investigating reports of corrosion-related brake failure in 1999 through 2003 Silverado pickup trucks.
Adler said that since the front and rear brakes are on different lines, drivers should be able to stop even if one of the lines ruptures. “GM does not see the rusty brake lines as a threat to safety because the brakes will stop the trucks,” he told ConsumerAffairs.
Nicholas of King of Prussia, Pa., said his 2000 Silverado 1500 lost its brakes at 27,462 miles due to excessive brake line corrosion. “Frame, brake lines, brackets, and suspension components were found to have systemic, abnormally high levels of corrosion,” he said.
“GM does not see the rusty brake lines as a threat to safety because the brakes will stop the trucks,” he told ConsumerAffairs. The National Highway Traffic Safety Administration (NHTSA) has been investigating reports of corrosion-related brake failure in 1999 through 2003 Silverado pickup trucks.
Where is the brake line on a Chevy Silverado?
Upon closer inspection, Sean said he found a leak in the brake line just under the driver’s side door. Nicholas of King of Prussia, Pa., said his 2000 Silverado 1500 lost its brakes at 27,462 miles due to excessive brake line corrosion.
How much does it cost to replace a brake line on a GM Truck?
“Brake failure and systemic corrosion required replacement of all brake lines on the vehicle: master cylinder through ABS module to each wheel cylinder” at a cost of $2,195. GM’s Adler said it shouldn’t cost that much. “Time studies for the repair showed it should take four to 4 1/2 hours based on $100 an hour for labor for a total cost of $500.
Upon closer inspection, Sean said he found a leak in the brake line just under the driver’s side door. Nicholas of King of Prussia, Pa., said his 2000 Silverado 1500 lost its brakes at 27,462 miles due to excessive brake line corrosion.
Can a brake line leak on a GMC Truck?
This can result in the lines leaking and failing brake and fuel systems, causing dangerous safety issues on your trusted GM/GMC 4WD truck. The solution to this problem is installing 100% correct replacement Chevy/GMC truck fuel and brake lines in stainless steel from CLASSIC TUBE.
What kind of car is a 98 GMC Jimmy?
98 gmc jimmy 4.3 liter. brake pedal to floor after ok previous day. eventually stops me although don’t stop on dime. hubby replaced lines from mc back (rubber and metal) part of line. Tried to bleed after replacing and it wont, none of them.
What kind of brake lines do Chevy trucks use?
The solution to this problem is installing 100% correct replacement Chevy/GMC truck fuel and brake lines in stainless steel from CLASSIC TUBE. These direct replacement stainless steel lines will last indefinitely, resisting rust and salt deterioration.
What’s the best way to replace brake lines?
-you will need to match the existing brake line diameter along with fitting type along with the lines being metric or imperial. -apply a small amount of oil to the end of the die which helps with achieving a high quality flare. Insert the dowel end in the line Thank you to all those who watch my videos and support my content.
