Why is my brake light not working on my Chevy Silverado?

Chances are the cause of the defective light or brake lights circuit on your Chevy Silverado is a simple problem. Moreover, you can blame most of these problems on little or no maintenance, according to James E. Duffy in “Modern Automotive Technology.”

Why are my brake lights not working after replacing the switch?

Brake lights still not working after I replaced brake switch. Running lights,blinkers,reverse all work. Fuses in panel good,bulbs good, what else can I check? There is a break light relay I think down under drivers side, or under the hood in the fuse box. Blinkers are working so the circuit is good. 32 people found this helpful.

Where are the brake lights on a Chevy C / K 1500?

There is a break light relay I think down under drivers side, or under the hood in the fuse box. Blinkers are working so the circuit is good. 32 people found this helpful. Thanks Rowefast, it was the brake light relay.

Why are the blinkers on my car not working?

Blinkers are working so the circuit is good. 32 people found this helpful. Thanks Rowefast, it was the brake light relay. Replaced it and they work fine 13 people found this helpful.

Where are the brake lights on a Chevy Silverado?

Check the Brake Lights Circuit. Start at the fuse box under the hood and make sure the brake lights fuse is not blown, that the terminals are free of corrosion and that the connections are tight. Then check the brake light switch on the bake pedal arm. Back probe the switch terminals with a test light.

Blinkers are working so the circuit is good. 32 people found this helpful. Thanks Rowefast, it was the brake light relay. Replaced it and they work fine 13 people found this helpful.

Where are the black wires at the brake light?

Black wires at the lamps provide the ground connections. Since 2003 Dan Ferrell has contributed general and consumer-oriented news to television and the Web. His work has appeared in Texas, New Mexico and Miami and on various websites. Ferrell is a certified automation and control technician from the Advanced Technology Center in El Paso, Texas.

What to do when your brake lights are not working?

In the situation when brake lights are not working properly, you need to make sure that the power is going through and check the fuse. If the brakes lights are turned on at the same time as turn signal lights, you need to bring it to the mechanics for a check.

Where are the brake lights on my car?

You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm. Any problem with the fuse box and light switch will affect the brake lights.

Is it illegal to drive without a brake light?

First of all, you will get pulled over and be fined by a police officer since it is definitely illegal to drive without a working brake light. Second of all, other drivers cannot see you very well in the dark. Without brake lights, it is impossible for them to know whether you are stopping or not, so accidents on the road are very likely.

Are there any brake lights that are not working?

Bed brake lights not… The bed brake lights are not working, but all other lights including the center mount brake light are working fine. I checked every fuse in both boxes and all four bulbs and they all appear fine.

What happens if you have a bad brake light switch?

The brake light switch on modern vehicles is no longer a simple switch used to turn on the brake lights. A bad brake light switch, for example, can trigger the ABS and traction control lights, but it can also prevent engine start or even transmission shifting. In this article, we go over the symptoms of a bad brake light switch and test them.

How do you know if your Chevy has a brake problem?

You will find the booster between the master cylinder and the firewall in your engine compartment. A check valve that is faulty can also let vacuum bleed out. You can diagnose this by starting your Chevy in order to build vacuum, and then turning it off for four or five minutes. Then you should try the brakes.

Why are my brake lights not working on my 1997 Chevy?

Pull the plastic cap off the fuse chassis and you’ll see a square relay fuse switch and replace it for the brakes. It’s only $13 bucks and is the predominant issue with 1997 Chevy Trucks and the brakes not working especially if you reverse and blinker lights do work. Was this answer helpful? Its the taillight circuit board or a broken wire.

What should I do if my brake light wont turn on?

Only one of the switch terminals should turn on the test light. When you depress the brake pedal, both switch terminals should turn on the test light. If only one of the wires turns on the test light, unplug the switch and jump the two connections at the connector.

Where is the brake light switch on my car?

Fuse Box and Light Switch. You have to find the fuse box or the power distribution center (PDC). You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm.

What are the symptoms of a bad brake light switch?

When the brake light switch does fail, usually the vehicle will produce a few symptoms that can alert the driver that a problem has occurred. Brake lights stay on. One of the symptoms commonly associated with a bad brake light switch are brake lights that stay on at all times.

What to do when your brake light comes on?

Why are my abs and brake lights not working?

This is how I fixed my intermittent ABS and Brake dash lights on my Chevrolet blazer with the Kelsey-Hayes EBCM module, with out spending 1500 bucks on a new EBCM.. You may have code C0265 “Electronic Brake Control Module Motor Relay Circuit.” The fault is usually due to broken solder joints on the circuit board.

What’s the code for ABS and brake light?

This is how to fix intermittent ABS and Brake dash lights on all Chevrolet vehicles with the Kelsey-Hayes 325 EBCM module. You may have code C0265 “Electronic Brake Control Module Motor Relay Circuit.”

Why is the brake light on in my Chevy Impala?

Either the brakes need bled, or there is a leak. Since you’ve already checked the emergency brake handle, now it’s time to check the master cylinder and see if the brake fluid is low or not. Now if it is low, but not empty, adding more may provide a temporary fix.

What to do if your brake light is not working?

If not, try replacing the bulb and see if that solves the problem. The only way to turn the brake light off is to restore proper line pressure to both brake circuits when the pedal is pushed. If your Silverado is having trouble stopping, or noticeably leaking fluid, don’t drive it. Just have it towed to a mechanic.

Are there brake lights on my Chevy Silverado?

My brake lights and blinkers do not work on rear end of my 1998 Chevy silverado. Blinkers work on front end. Tail lights Chevrolet Silverado 1500: My brake lights and blinkers do not… No lights in the back. Brake, tail, blinkers. No lights at Professional at Justanswer… Vocational, Technical or Tra…

Why does the emergency brake light stay on in my Chevy C1500 pickup?

Why Does the Emergency Brake Light Stay on in My Chevy C1500 Pickup? Vincent Ciulla is a certified master automotive technician who has diagnosed and repaired light trucks, domestic and foreign cars, and diesel engines, for more than three decades.

Why do my brake lights and blinkers not work?

Here is what is going on: I have a 1998 Chevy Suburban 1500 4X4 5.7 with a blinker-tail light issue. Currently, I have brakes and hazard lights. … read more Vocational, Technical or Tra… Both tail lights and brake lights dont work right. the right turn signal works.

What kind of car has no brake lights?

I have an 1994 Chevy Silverado 1500 I have problems with, when you turn on the headlights the tail lights and brake lights don’t work. With the … read more

Why are the tail lights on my Chevy Silverado not working?

Tail lights not working on 1998 Chevy Silverado, bulbs ok check blinker relay it is ok. Fuses are OK. What could be the problem please … read more My 1999 Chevy Tahoe’s rear driving lights do not work nor do my dash lights behind the steering wheel. My husband has changed all the bulbs and also the fuse several times. How do we find the short?

How can I tell if my brake light is working?

The test light should not come on (or volt meter show no voltage). With the leads in place, depress the brake pedal. The test light should illuminate (or volt meter read 12 volts) if the brake switch is operating properly. Otherwise, the switch is defective and should be replaced.

If none of the brake lights on a vehicle light up when applying the brake, there is a good chance that the brake light switch is defective. Testing this switch is one step in troubleshooting brake light problems. Look under the dash and locate the brake light switch near the top of the brake pedal.

Why is my brake light not working on my car?

If the brake light switch is functional, you have to check for a bad electrical ground (some car models have the switch provided ground). It could happen due to a loose connection of the wire or the corrosion or damage of the wire ends.

Why are the brake lights not working but the tail lights are?

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.

Is it dangerous to drive with brake lights not working?

Driving at night with either brake lights or tail lights not working is dangerous for you and other drivers on the road. It takes a long time to notice when the brake lights not working but tail lights are or vice versa. It is so because you won’t know what is happening in the backside while driving until someone points it out.

Why is my brake light not working on my Chevy Silverado?