Where is the rear axle on a Ford Explorer?

The Driver’s side. If you look at the Explorer 8.8 rear axle, you will notice the driver’s side axle tube is longer than the passenger side. This actually offsets the differential “pumpkin” to the passenger side.

Can a rear axle be interchanged with a passenger axle?

Axles can be interchanged within housings of the same width. The passenger side axle has a threaded adjuster to set axle shaft end play. 4) There was a slight dimensional change in axle shaft length when the Sure Grip design changed.

Is the front axle a live axle or a dead axle?

Live front axle. Dead front axle. The front axles are usually dead axles because they do not rotate, in contrast to the live axles that they are used in the rear axle to transmit power to the rear wheels.

How are the wheels attached to the front axle?

The figure shows front axle components with the steering linkage. The wheels are fixed on the stub axles which are usually pivoted. From the stub axle, the inclined steering arms are connected to the track rod ends, and a third steering arm is attached to the drag link.

Where is the lubricant plug on the rear axle?

Enjoy fast shipping and great savings on all driver and passenger side.REAR AXLE The rear axle contains a lube oil level check plug near the drivers side. Checking the Lubricant Level Take out the check plug, Check the level, the optimum lubricant level is just below the bottom end of the threaded hole, Should lubricate be needed, .

What is an EZGO rear axle exploded diagram?

Ezgo Axle Diagram – Explained Wiring Diagrams – ezgo rear axle exploded diagram | ezgo rear axle exploded diagram. 11 Ez Go Schematic. Purchase EZGO rear axle parts, including axle clips, snap rings, bearings, and more.

What kind of rear end differential does a Chrysler 9 ¾ have?

The early rear ends were 23 tooth “Power Lok” (1966 – 1969) differentials. In 1970 the 9 ¾ went to 35 tooth axle shafts and were called “Track Lok” differentials. These particular ones will interchange with 8 ¾ axles, bearings and seals. Last year in A bodies: 1972 Last year in E bodies: 1974.

How many axles does a Ford Explorer have?

It literally is near endless because the Ford 8.8 is a common differential. Just remember you will have TWO passenger side axles if you choose to order upgraded axles. Questions or comments about this section? Post them below or Email The Fabricator

Where can I find list of Ford differentials?

You can use the social sharing buttons to the left, or copy and paste the website link: https://www.diyford.com/ford-axle-history-identification-ford-differentials/ As part of my research, I went to renowned Currie Enterprises and gathered one of just about every different 9-inch axle variant.

Where are the Axles installed on a 1967 Ford?

The 1960s to 1967s still retain the dimples but also have an oil level plug in the back cover. The Ford 8.8-inch axle has a cast center section and the internal components are installed from the rear. There is typically a stamped steel cover that must be removed to gain access to the internals.

What do you call the rear axle assembly on a Ford Explorer?

(What you see below is a previous search for a Ford Explorer Rear Axle Assembly and does not include all the Rear Axle Assemblies in YOUR area.) This part is also known as Ford Explorer Rear Axle Assy; Ford Explorer Axle Assembly, Rr.

Where are the axles on a Ford Ranger?

Are the Dana 35 “hybrid” axles with the Dana 28 guts. This number can be found at the top-left of the label located on the backside of the passenger side axle beam. For SLA axles, it will be on the passenger side axle tube.

Are there any problems with the Ford Explorer?

In addition, rear end has a bad rattle even on smooth roads. There is about 59,500 miles on the SUV and it was just state inspected. We are afraid to drive it. Checked complaint boards and there are many similar problems. Tl- the contact owns a 2014 Ford Explorer.

What’s the safety record of a Ford Explorer?

Today’s Ford Explorer receives high ratings on crash tests and has a good overall safety record thanks to its tough construction that has the ability to handle even the most challenging driving terrains. Spanning 25 years, there have been five generations of Ford Explorers.

Where can I get a Ford Explorer suspension ball replaced?

The contact took the vehicle to langdale Ford (215 w magnolia st, valdosta, GA 31601, (229) 394-4334) and was informed that the rear suspension ball joint needed to be replaced. The contact received a second letter from the manufacturer which stated that the vehicle was not included in the recall repair.

Is the Ford Explorer a good off road vehicle?

Though the Ford Explorer can drive well on the highway and off-road, you may want to find a Ford Explorer parts catalog source to peruse for Ford Explorer performance parts in order to enhance your riding experience. For a source that has various Ford Explorer accessories and parts, look no further than a site like PartsGeek.com.

What are the features of the Ford Explorer?

Some of the most impressive features on the latest generation Explorer include remote engine start, push button start, power adjustable pedals, active park assist, Ford SYNC by Microsoft, MyFord Touch, solar tined windshield with rain-sensing wipers and power lift gate.

When did the fifth generation Ford Explorer come out?

Side curtain airbags were added in 2008, and Ford upgraded the satellite-operated navigation system with voice-activated controls. The fifth generation Explorer, which is the current model, was introduced in 2011, and features a floating roof effect, stepped-style head and tail lamps and the three-bar grille.

Where is the differential located on a rear wheel drive car?

It is located on the rear axle of rear-wheel-drive vehicles, where the driveshaft meets the axle. The bulge in the axle houses the differential. On front-wheel drive vehicles, the differential is located at the end of the transverse-mounted engine. On a part-time 4-wheel drive, the front and rear differentials lock together when engaged.

How do you remove the rear axle shaft?

Pull the hub assembly up and pull the axle shaft out of the hub assembly. Pry the other end of the axle shaft out of the rear differential using a flat-tip screwdriver. For specific information about removing your vehicle’s rear axle shaft, consult the particular vehicle’s manual. (see Resources)

Where does the rear axle shaft come from?

A rear axle shaft is found on vehicles with rear wheel drive or all wheel drive. The rear axle transfers power from the rear differential to the drive wheels. The axle uses two joints to provide flexibility in the joint.

What’s the difference between a Ford Explorer and a Ford Ranger?

The 8.8-Inch axle used in the Explorer is highly desirable because it came with 31-spline axles over the typical 28-spline found in the Ranger version. There’s a 20-25 percent difference in strength between this Explorer 8.8 and the Ranger 8.8.

What kind of disc brakes does an explorer have?

The 1990-1994 Explorer 8.8-inch axle came with 10-inch drum brakes. 1995 and newer Explorers have disc brakes. People have reported that they have swapped in a newer disc brake 8.8-inch axle in place of their original drum brake axle without having to switch to a disc brake master cylinder. Spring Pads – Removal:

How do you change the tail light on a Ford Explorer?

Changing a tail light or even replacing a broken lens on the rear of your Ford car or SUV is very simple, and you only need a cross tip (Phillips) screwdriver to do the job. Locate and remove the screws holding the tail light in place. In this case, there are 2 screws holding the tail light in.

How do you replace a brake light on a Ford Explorer?

Place the bulb in its respective place on the lens, and secure it by giving it a quarter turn. Attach the lens to the vehicle, making sure all the wires are neatly tucked in. Secure the side with the plastic pegs first. Then replace the screws. Check lights, back-up lights, brake lights and turn signals to make sure everything is working properly.

What kind of bearing does Ford Explorer have?

A shop press is required to service this bearing. The example vehicle is a 2002 Ford Explorer 4X4 however this example is similar to many 2000-2010 Ford Explorer and Mercury Mountaineer vehicles. Watch this video for more information. Loading…

Where does the Explorer van company come from?

Founded in Warsaw, Illinois, Explorer Van Company strives to put the customer above all else, delivering an enjoyable, durable product that satisfied customers have bragged about then and now. Here at Unique Concepts, our goal is to make sure that you continue to enjoy your Explorer Conversion Van.

Can a welder make a Ford Explorer narrower?

A welder rated for 26 Gauge sheet metal to ¼” steel is technically not a capable welder because you are welding at the maximum rating. Welding at max can lead to a weak weld due to low duty cycle. It is possible, but not recommended.

Where is the rear axle on a Ford Explorer?