Where do I find the turn signal relay?

Locate the turn signal relay. This should also be in your owner’s manual. If it’s not, you can consult a service manual for your car. Once you can see your relays, remove the old turn signal flasher relay and replace it with the new one. Don’t worry about installing it incorrectly, it will only go in one way, the right way.

How to check and replace a turn signal Flasher?

1 Locate your relay cluster. You can find this in your car’s owner’s manual. 2 Locate the turn signal relay. This should also be in your owner’s manual. If it’s not, you can consult a service manual for your car. 3 Once you can see your relays, remove the old turn signal flasher relay and replace it with the new one. …

How can I tell if my turn signal switch is bad?

Check for a bad connection between the turn signal switch and the flasher or between the flasher and the ignition switch. Check the power side connection to the turn signal switch for a bad contact or open. Finally, check for an open or short in the lamp’s circuit. Identify the wires in your turn signal switch using your repair manual.

Why is my left turn signal light not flashing?

Operate the switch to turn the left turn signal light. Back probe the wire that supplies power to the switch; the test light should flash. If the test light doesn’t flash, there is a problem with the flasher unit or an open or short between the switch and the battery power source.

How to repair a turn signal relay in Chevy Silverado?

Open the fuse box and using the diagram on the underside of the lid, examine the fuses that have something to do with turn signal lights or hazard lights. If all these fuses check out, then the issue is almost definitely the flasher unit or the multi-switch on the steering column.

Can a GM turn signal Flasher be plugged in?

【Feature】If you’re going to do a LED lights upgrade for your GM vehicle, this led flasher relay is a must have item – solve the hyper flash problem with simple a plug and play. 【Note】Use this flasher relay, never cut your factory wires and install a load resister. (use the load resister basically shorting out the circuit)

Why is my turn signal relay not working?

Be sure that your pal appears to be like for the lights when you’ll be able to hear the lights operating at a slower or faster speed. 2. Examine every of the flip signal gentle bulbs, especially the bulbs that you simply found not working. Most frequently, a bulb that burns out triggers an issue with the turn sign relay. 3.

Do you need an LED flasher relay for a turn signal?

If you’re going to do a LED Lights Upgrade for your vehicle, this led flasher relay is a must have item – solve the hyper flash problem with simple a plug and play. We are a team with more than 50 young guys who are car enthusiasts.

Where are the bulbs on a turn signal?

Tracking down a loose wire or a ground that isn’t grounding can be a pain in the neck. But let’s get to it. In order to replace your bulbs, you had to access the back of the turn signal housings. Also in this location, you’ll find the plugs that connect your tail lights and front turn signals to the car’s electrical system.

What’s the best way to troubleshoot a turn signal?

Matthew Wright has been a freelance writer and editor for over 10 years and an automotive repair professional for three decades specializing in European vintage vehicles. Turn signals are one of the easiest systems in your car to troubleshoot.

How to replace your turn signal relay in Dodge Durango?

Test the relay by placing you finger on the relay housing and activating the turn signal. If you have found the right one, you should feel a clicking as the turn signal blinks. Remove the relay, replace with the new relay and close the access door. Start the Durango and activate the turn signals to check that they each work.

Where is the turn signal relay on a Dodge Intrepid?

On some models of the Dodge Intrepid, there isn’t a panel present, because the steering column cover houses the relays. Look on the underside of the relay panel for a diagram, to locate exactly where the turn signal relay is. If there isn’t a diagram, start in the upper right hand corner of the box and compare the existing relays to the new one.

What are the symptoms of a bad Flasher relay?

Another symptom of a faulty flasher relay is hazards or turn signal lights that stay on. If the flasher has any sort of internal short it may cause the hazards or signals to stay on when they are activated, instead of flashing.

How do you test a turn signal relay?

Open the access door and view the collection of relays and fuses. At the left side of the mounting block is a larger flasher and relay. This is the combination turn signal flasher and relay. Test the relay by placing you finger on the relay housing and activating the turn signal.

How is the direction of a relay determined?

Or they can also be set to trip for faults behind the relay in the reverse direction. Forward and reverse are typically determined by the normal flow of current into the relay, so be sure to confirm the CT connections before you make any assumptions. Incorrectly determining forward and reverse is an easy mistake to make.

What does directional overcurrent relaying ( 67 ) mean?

Abstract – Directional overcurrent relaying (67) refers to relaying that can use the phase relationship of voltage and current to determine direction to a fault. There are a variety of concepts by which this task is done. This paper will review the mainstream methods by which 67 type directional decisions are made by protective relays.

How does a direction signal system work on a car?

A direction signal system is designed to operate with a flasher or blinker unit which interrupts the signal which created the blinking action. Learn more – Locate turn signal flasher in Google Images.

Which is 6 volt or 12 volt turn signal relay?

111953185C 6 Volt Turn Signal Flasher Relay. This model can also used for 1966 & earlier models that have been converted to 12 volt systems. Replacing the Turn Signal Relay is very simple. The terminals are labeled, their designations are:

What are the switches on a VW headlight relay?

The VW Turn Signal Switch wiring is a very simple circuit, even with the switch controlling the Headlight Relay. The designations for the wires are: NOTE: The 3 GREY WIRES ARE DUPLICATES AND ARE NOT USED.

What happens if the directional relay is set in reverse direction?

If the directional relay set in Forward direction means if a fault occurs in forward zone then only relay operates. Conversely, if the relay set in Reverse direction means if a fault occurs in reverse zone then only relay operates.

Abstract– Directional overcurrent relaying (67) refers to relaying that can use the phase relationship of voltage and current to determine direction to a fault. There are a variety of concepts by which this task is done. This paper will review the mainstream methods by which 67 type directional decisions are made by protective relays.

What should the MTA be for directional overcurrent relaying?

An MTA in the range of 300 to 750 is common. When setting MTA, if an overcurrent element is to be set below reverse direction load current, there is a risk of the element seeing abnormal forward load conditions as reverse fault current, as seen in Fig.

What is the forward zone of a relay?

At this line relay current is in phase with the reference or polarising voltage. It is the boundary line which separates the plane into Operate and Inhibit regions. Forward zone is+/- 85° either side of the Maximum Torque line or Centre of forward zone line.

What to do if your turn signal is not working?

Unplug these and plug them back in one at a time. Sometimes just the act of unplugging and replugging can renew the connection and solve your issue. Don’t be surprised if one of the plugs that you didn’t think was affecting the turn signal system turns out to be the cause of your problem. Turn signals are tricky like that.

Where do I find the turn signal relay switch?

It should be underneath the steering column and above the brake pedal . On some earlier models, there may not be a panel cover. Use a screwdriver to remove the relay panel and look on the underside of that panel for a relay diagram. This diagram should tell you exactly where the turn signal relay is located.

Where is the turning signal relay located at?

Look on the underside of the relay panel for a diagram, to locate exactly where the turn signal relay is. If there isn’t a diagram, start in the upper right hand corner of the box and compare the existing relays to the new one. Use the information on the back of the relay for comparison purposes.

Where is the turn signal/hazard relay located?

Locate the turn signal and hazard flasher relay. It is located under the driver’s side dash below and behind the fuse box . Remove the cover of the fuse box. Using a screwdriver, remove the screw holding the fuse box in place.

What are symptoms of a bad turn signal relay?

Another symptom of a bad turn signal relay is that it stays on, instead of flashing. Despite lighting up, they won’t emerge others that the driver want to turn left/ right or other situation. The mainly result of this problem is electrical issues. Therefore, checking the vehicle regularly is necessary.

What do I need to know about my Dodge alarm system?

These Dodge Wiring information / Aftermarket Autostart/Alarm Technical Wiring Diagrams are very useful, if not required, for the installation of alarms, autostart / alarms, remote starts, doorlock info and any other aftermarket installation that would require you to know the / Wire Information / Wiring Information of your Dodge

Where is the camshaft sensor on a Dodge Ram?

The camshaft position sensor, which is located inside the distributor, is a pretty easy component to test on the 1992-1995 5.2L/5.9L Dodge Ram 1500/2500 pickup. With the help of this tutorial, you’ll be able to find out if it’s bad or not in 3 tests. All 3 tests are done with a multimeter.

Why is my turn signal not working on my Dodge Ram?

However, the most common cause of relay damage is attributable to an electrical fault in a relative location, such as the taillight assembly. You can find and replace the turn signal relay in your Dodge Ram 2500 with a few common tools.

Can you replace the turn signal relay on a Ram 2500?

You can find and replace the turn signal relay in your Dodge Ram 2500 with a few common tools. You can do this job at home; it should take you less than 20 minutes to do.

Where are the fuses on a Dodge Ram?

On left inner fender panel. On left fender panel. On left inner fender panel. On fuse/relay block. To right of steering column, on bracket. On fuse/relay block. Left of steering column, taped to main harness. Integral part of rear defogger switch. On left inner fender panel. On fuse/relay block.

How to add turn signals and wire them up?

Use a factory switch. 2. Use an aftermarket switch. 3. Make your own switch system. (It’s easy!) Factory switch Most of you will have a hotrod that uses a steering column that has a turn signal switch built in. What you need to do is find the wiring diagram for the vehicle the column came from.

How can I Fix my Turn signal problem?

Step 1 – Turn the ignition key to the “ON” position, (do not start the engine) this will power up the electrical system for testing. Step 2 – Locate the power distribution center (PDC) or fuse panel to check all system fuses. Learn more – To locate the fuse consult the owner’s manual or search Google Images.

What does it mean when your turn signals stop working?

If your turn signals have stopped working, it’ll be doing one of these things: blinking rapidly, coming on without blinking, or nothing at all. The good news is that all of these symptoms point to two possible issues, a bad turn signal relay or a dead bulb.

What do you need to know about turn signal relay?

The turn signal relay is the electrical system that dictates your car’s turn signal. If you think about your car’s turn signal, you know there has to be an electrical system to make the signal turn on and blink. This is all done by a system called the turn signal relay. The majority of turn signal lights are controlled by a flasher.

Is there a turn signal for both left and right?

Although some models use a separate light for the left and right turn indicators, other models use a single light for both turns. If your instrument panel has only one indicator light for both left and right, check the flasher unit. Some vehicle models combine the brake light, taillight and turn signal into one light bulb.

What should I do if my turn signal bulb is bad?

Most likely, the turn signal bulb is a two-filament type. Make sure both filaments are in good condition, and that the bulb glass is not darkened. Otherwise, replace the bulb with another one of the same type and wattage. Examine the bulb socket for corrosion or damage.

Where is the ignition relay located in a car?

The ignition relay is often located in the fuse box under the hood. It can also be located in a fuse box under the dashboard inside of the car. The ignition relay’s exact location may differ from vehicle to vehicle depending on the design of the vehicle and the company that manufactured it.

Where are the fuses on a Volkswagen Polo 6R?

Fuses and relay Volkswagen Polo 6R F1 (5A) Control unit in dash panel insert A F2 (10A) Steering column combination switch F3 (5A) Fuel pump relay Engine control unit F4 (2A) Combination switch F5 –

Where is the fuse box on a Volkswagen Transporter?

fuse box location. The central electrics with the relay is on the left in the footwell behind a hinget shelf. fuse box diagram. legend. (15A) Rear screen wash/wipe system, ignition auxiliary circuits relay 2, accessories (15A/20A) Windscreen wash/wipe system, heated windscreen washer jets (05/01^)

Where are the fuses on a Volkswagen Golf?

Fuse box diagram (fuse layout), location, and assignment of fuses and relays Volkswagen Golf IV (Mk4 / 1J) / Bora (1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006). The fuses are designed to blow before the entire wiring harness is damaged. If any of the electrical components do not operate, a fuse may have blown.

What does the green light on the VW dashboard mean?

Switch the ignition off and on again if this inspection light comes on. If the light stays on, contact an authorized Volkswagen dealer or service facility. This green light means the brake must be applied to shift vehicle into gear. There is a problem with your steering column.

What does the yellow warning light on a VW mean?

The solid yellow Volkswagen warning light means ESP/ASR is inactive. A flashing warning light signifies an ESP/ASR event. Contact your local authorized Volkswagen dealer for more information. The yellow check engine light code could mean your filter is blocked with soot. See owner’s manual for more information.

What does yellow EPC symbol on VW dashboard mean?

See owner’s manual for more information. If the yellow engine emission malfunction dashboard indicator light comes on, please bring in your vehicle to your local authorized Volkswagen dealer for service. The yellow EPC dashboard symbol means engine malfunction—bring your vehicle in to your local authorized VW dealer for service.

What causes a turn signal to stop blinking?

Troubleshooting your turn signals isn’t tough. If your turn signals have stopped working, it’ll be doing one of these things: blinking rapidly, coming on without blinking, or nothing at all. The good news is that all of these symptoms point to two possible issues, a bad turn signal relay or a dead bulb.

Where are the fuses located on a Ford F250?

Replace the fuse with one that has the right amperage rating. It is located behind the cover on the instrument panel. The high current fuses contained in the Power Distribution Box protect your vehicle’s main electrical systems from overloads; these fuses provide the connection between the battery and your vehicle’s electrical systems.

Why do I need a Ford turn signal relay?

Ordered this relay to replace the original blue ford turn signal relay due to hyper flash after installing LED turn lights fronts and backs for the first time. Relay fit as described, worked for the hazard lights perfectly but zero response from either left or right when used individually.

Where are the fuses on a 1995 Ford F150?

Fuse Location and Description 1995 Ford F150, F250, and F350. In the table below you’ll find the fuse location and description of the fuses of the instrument panel fuse box on 1995 Ford F150, F250, F350. The fuse box is located on the driver side of the dash.

Do you need LED lights for Ford F-250?

Was upgrading my Ford F150 to LED lights I needed a LED light flash relay this one works perfectly well constructed easy to install and worked like a charm. This product does NOT work for the 2009 Ford F-250. The F250 utilized the PMC to activate flashing. I fielded a question regarding this concern to this seller and received NO response.

What to do if a fuse is blown on a Ford F250?

Check the fuse to see if it is blown. Look through the clear side of the fuse to see if the metal wire inside is separated. If it is, the fuse is blown and should be replaced. Replace the fuse with one that has the right amperage rating.

Where are the ignition coils on a Lincoln?

Lincoln Ignition Coils New! Turn Signal Switches NEW! Turn Signal Switch NEW! Turn Signal Switch New! Turn Signal Switch NOS! Turn Signal Switch New! Turn Signal Switch New! Turn Signal Switch New! Turn Signal Switch New! Turn Signal Switch New! Turn Signal Switch New! Turn Signal Switch New! Emergency Flasher Knob – Chrome New!

Where is the window regulator on a Lincoln?

Located inside the head of the window motor, remove the window motor to check to see if yours has failed. New! Window Regulator Roller – Large New! Window Regulator Roller – Small NEW! Quarter Window Gear New! Window Regulator Roller – Large New! Window Regulator Roller – Small

Where are the window gears on a Lincoln?

NEW Window Motors and Gears – Before buying window motors or switches check to see if all you need is a Window Gear. Located inside the head of the window motor, remove the window motor to check to see if yours has failed. New! Window Regulator Roller – Large

Are there any aftermarket parts for a Lincoln?

Start browsing through our collection of aftermarket Lincoln parts and accessories today! Lincoln Backs out of EV Project With Rivian A couple of months later, though, the project would fall victim to the effects of the coronavirus pandemic on the automotive industry and the world’s economy as a whole.

Where is the turn signal flasher on my car?

I have located the hazard flasher under the dash behind the brake pedal on the firewall and was wondering if the flasher right next to it is the turn signal flasher because while I was driving I turned on my turn signal and it made a strange buzz noise under my dash and then I had no signal lights and was wondering if this might have burnt out.

Where is the turn signal on a Mercedes?

The turn signal switch is part of the combination switch found in the steering column and is mounted right behind the steering wheel. You may also notice that the wiper switch is not working either.

Why are the indicators not working on my Commodore?

Cheers toomanytoys – Ill check the hazard light switch. They come on as hazards, tho. all 6 bulbs flash at once, but i cant operate the LHS or RHS individually with the indicator stalk. Yeah but using the indicator stalk, there is nothing. Flasher unit doesnt even click, so nothing is even making it to the bulbs.

Why are my high intensity discharge ( HID ) headlights not working?

High intensity discharge (HID) headlights can also fail due to other associated components. Neither of the headlights work. The cause: Burned out bulbs, or an issue with power or ground. The fix: Check for power and ground, and fix if necessary. Otherwise, replace the bulbs.

Why is indicator not working, bulb fine, relay?

I’ve got a 2000 suzuki where the indicator went on the left, I replaced and decided to replace the rh one too. rh stopped working totally, bulb was fine. This was simply down to the earth on the bulb housing. It was stuffed up the side of socket and folded back on itself to connect to the bulb housing.

How do you change rear indicators to LEDs?

Maybe you only want to change your rear indicators to leds and leave the front indicators standard or youre struggling to find the right led relay for your bike. Connect the cathode k or end of the led to the resistor then the other end of the resistor to the negative side of the battery. Installing led lights in your vehicle.

Where is the dash Speedo indicator bulb located?

The dash speedo indicator bulb used with the 3-terminal flasher relay is connected from the (+) supply to #49a and it flashes oppositeto the Turn Indicator bulbs. For example, when the Turn Indicator bulbs are lit, there is +12V present at #49a. That means that bothsides of the dash bulb have +12V on them and no current can flow thru the bulb.

Where does the load resistor go on an indicator light bulb?

The load resistor has to be connected to the two wires that go to the indicator or tail light bulb holder one end to the postive live wire the other to the negative earth wire.

How can I tell if my turn signal switch is working?

However, if the flasher unit is working fine, check the fuse. Also, check for a bad connection at the turn signal switch or an open in the part of the circuit that connects the flasher unit to the turn signal switch. See the section ‘Checking the Turn Signal Switch.’

Why does my turn signal light up but not flash?

Turn signals are tricky like that. If your turn signal doesn’t light up at all or doesn’t flash, it can often be a bad ground connection that’s the culprit. In most vehicles, the ground wires will be either brown or black.

What to do if your fuse box is clicking?

If that relay also clicks constantly, you need to run more tests. If that relay works fine, then the original relay that was in that spot is faulty. Simply replace that relay with a new one. Identify the terminals on the relay. Look at the terminal labels on the relay.

What does it mean when a relay does not click?

If you hear or feel the relay click, the relay and its wiring aren’t the problem. But if it’s not clicking, the problem could be in the relay itself or in the wiring.

When do you need to troubleshoot a relay?

That is, on a horn, 12V should always be present on 86, and 85 is grounded when the horn button is pressed). If the control side fails either of these tests, you must troubleshoot the wiring. Often it is a problem in whatever is switching the control side on and off.

Can you feel the contacts closing on a relay?

You also can feel the contacts closing if you lay your hands on the relay. So, for example, if your horn doesn’t work, the first thing to do is turn it on (e.g., hit the horn button), and listen to and feel the relay.

Why does my Hagerty relay not show continuity?

If the relay does click and 30 and 87 do show continuity, there is still the possibility that the internal contacts are corroded and a voltage drop across them is preventing full current from flowing. Take that thought and park it for a moment. If the relay itself tested as good, then the relay wiring must be tested next.

Why does my turn signal relay stop working?

There is typically an underlying factor as to why they stop working. One of the contributing factors could be from a failing turn signal relay. If you are trying to determine if the turn signal relay is the root of the problem, you will have to look at the whole electrical system.

How to identify terminal pins of a relay?

Set your multimeter to continuity test mode. Try to touch the probes of multimeter on remaining pins to determine which are the pins actually connected with each other.These pins actually consist of normally closed (NC) pin/pins and common pin/pins. Based on this finding, the remaining pins must be normally open (NO) pins.

Do you need a relay for Your Headlights?

Most manufacturers did not use a relay for the headlights up until very recently. I used a Daniel Stern relay kit for this installation which went very smoothly. It was really nice to have everything necessary to get the job done in one purchase off of the internet rather than having to hunt down individual parts.

Do you need a flasher for a turn signal?

Some vehicles have separate flasher relays for turn signals and hazard lights. Be sure to check both systems while you’re thinking about signal relays. Hazard lights can be very important.

How can I change the turn signal on my car?

If the contacts are worn, warm the contact pad with a soldering iron and drop a blob of solder into the copper, to build up the area. The turn signal switch can also be upgraded to one with a fog-light ring if equipping a vehicle with factory wired fogs.

What causes a turn signal to be inoperative?

The usual cause of inoperative turn signals is a defective bulb or flasher unit. Prior to performing extensive diagnosis, check the vehicles fuses to ensure they are not blown. Some vehicles utilize two fuse boxes, one in the passenger compartment and another under the hood. Consult your owner’s manual for fuse box locations and fuse ratings.

Can a bad fuse cause a bad turn signal?

Bad grounds and connections are a possibility, but a bad fuse or flasher is more likely. Turn signals on either side of the vehicle can be wired in series, much like the bulbs on a strand of Christmas tree lights. If one goes bad, or it isn’t properly grounded, it can affect the corresponding light on the same side.

Is there a way to test a turn signal?

Only the Front Right Turn Signals don’t work. Or only the Rear Right Turn Signals don’t work. Since the turn signal switch isn’t cheap (at your local auto parts store expect to pay about $150 US), it’s best to test it and make sure it’s really bad.

Are there turn signals on the front of the car?

No Front Left Turn Signals. No Rear Left Turn Signals. No Front Right Turn Signals. No Rear Right Turn Signals. One last and very important thing, this article assumes that you have already eliminated the turn signal flasher as the cause of the problem.

How can I find out if my trailer light is bad?

If all the lights appear dim or you have no lights at all, check the trailer light harness at the tow vehicle. First disconnect the harness and plug a tester (Photo) into the receptacle from your vehicle. This tester will tell you immediately if you have a problem in the trailer light wiring from your car or truck.

How can I check the wiring on my trailer?

Check the trailer wiring by running a continuity test by connecting a jumper wire to the connector pins and a continuity tester to the sockets. Connect the jumper wire to one of the pins in the trailer socket. A continuity tester contains a light bulb and a battery.

Why are my trailer marker lights not working?

If you are still having problems inspect the wiring from the connector back and fix any pinched or damaged wires. It could also be a ground issue. the lights should be grounded to clean and corrosion free bare metal surfaces.

Why are my brake and turn signal lights not working?

Believe it or not, you could have a BCM code that is stopping your brake and turn signal lights from working. Most people don’t have access to a scanner that can access the BCM, so you will most likely need to book an appointment with us to do this. If there are no codes in the BCM, it is most likely the BCM that needs to be replaced.

Why is my turn signal not working on my GMC Sierra?

I swapped out 05 GMC Sierra tranny , put in tranny from 07 , used n/s switch from old tranny, car hesitates to shift , drive ,3 gears want catch can only drive in 2? Is it really required to do maintenance like change oil and filters each 3k miles?

What can cause a bad turn signal relay?

The broken flasher is the most popular symptom of a bad turn signal relay. It can cause the lights do not function when you press the hazard light button. Although this problem may not lead to serious engine performance issues, it’s so dangerous when your turn signals aren’t working. If the signal blinks really fast, you may have a dead bulb.

Where is the turn signal on a GM Truck?

This relay is found behind the fuse panel on the left side of the dash. The easiest way to get to it is Pull the plastic trim around your gauges. You can do this by lowering the steering wheel as low as it can go and then moving the shift lever down all the way. You’ll have to use your key, turn on and then lower. Then carefully pop the trim.

Where is the relay on a 2003 Silverado?

Seems like a Relay starting to go bad. The Orignal part# that I pulled out from my 2003 Silverado is 15764153. 2/4-W/Opt. Trailering. This relay is found behind the fuse panel on the left side of the dash.

Which is GM hazard warning and turn signal Flasher?

ACDelco GM Original Equipment Hazard Warning and Turn Signal Flasher is a GM-recommended replacement component for one or more of the following vehicle systems: body-electrical and lighting. This original equipment flasher will provide the same performance, durability, and service life you expect from General Motors.

Where are the fuses on a Chevy Blazer?

The fuses are located below the dash panel. Horn, Dome & Glove Box Lights, Clock, Courtesy Lights (1982-1984), Lift Gate Release Solenoid (1982-1984), Cigarette Lighter

What are the fuses on a GMC Sierra?

Cruise Control, 4 WD Display Illum. Rear Window Defogger Timer, Aux. Batt. Relay Feed, Safety Belt Buzzer Timer, Cluster Ign. Feed Ign. A Dome Lamp, Cargo Lamp, Ctsy, and Glove Box Lps.

The fuses are located below the dash panel. Horn, Dome & Glove Box Lights, Clock, Courtesy Lights (1982-1984), Lift Gate Release Solenoid (1982-1984), Cigarette Lighter

How can you tell if there is a fuse in your car?

The wiring circuits in the vehicle are protected from short circuits by fuses. This greatly reduces the chance of damage caused by electrical problems. To check a fuse, look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse.

Where do I find the turn signal relay?