What is the SRS airbag light code b0100?

B0100 is for the left Front Driver Side Sensor & B0103 is for the Right Front Pass… This Video is for those who are getting Airbag Light code B0100 or B0103 .

Do you need scanner to read airbag trouble codes?

Working with your airbag system is crucial, and therefore, always read the trouble codes with an OBD2 scanner to get an idea of where to start your troubleshooting. Do never clear the trouble codes before you fix the problem caused by the airbag light.

Do you clear trouble codes before resetting airbag light?

Do never clear the trouble codes before you fix the problem caused by the airbag light. Read the codes and get information about what can cause the problem and therefore continue the diagnosis. You should never just reset the airbag light without repairing the problem.

Why is my airbag light on code b0103?

There are numerous conditions that can set the B0103 code. Can be a short to ground in the circuit, high resistance in the circuit or the sensor or an open in the circuit or the sensor. Re: Airbag light is on code b0103 cannot locate it

B0100 is for the left Front Driver Side Sensor & B0103 is for the Right Front Pass… This Video is for those who are getting Airbag Light code B0100 or B0103 .

What is the front bumper airbag sensor code?

This is on my 05 Sierra 1/2 ton crew. Managed to locate a scanner that will show airbag codes, and it appears to be one of the 2 front bumper sensors (which I believe are mounted on the rad supports). The code read “front end sensor 2 fault”

What does the code 13 on an air bag mean?

Code 13 (single flash, pause, three flashes) means that the airbag circuit has shorted to ground and Code 14 (single flash, pause, four flashes) means that the primary crash sensor circuit has shorted to ground. These codes are signaled by two flashes, a two-second pause and the number of flashes that corresponds to the second digit.

What is the Flash code on a Ford air bag?

Lamp flash code: 13 1.3 DTC B1317: Battery voltage high. Lamp flash code: continuous 1.4 DTC B1318: Battery voltage low. Lamp flash code: continuous 1.5 DTC B1342: Air bag control module is defective. Lamp flash code: 12 1.6 DTC B1869: Air bag warning indicator open circuit or short to ground.

What does the code on the air bag indicator mean?

If the system detects any problems, it gives you a signal through the airbag indicator by flashing the light several times, giving you the specific problem the test has detected. These flashes are codes, each having its own meaning. The supplemental restraint system (SRS) warning light is most commonly known as the airbag system light.

What is the DTC code for a airbag module?

Third Row Left Roof Rail Deployment Loop Resistance Above Threshold Third Row Left Roof Rail Deployment Loop Resistance Below Threshold Left-hand Side Impact Airbag Module Deployment Circuit -Short To Ground or Earth Or Voltage (12 volt VSS) Left-hand Side Impact Airbag Module Deployment Circuit -Short To Ground or Earth Or Voltage (12 volt VSS)

What does b0103 stand for on a sensor?

Code B0103 is for the right side front sensor. Here is the test just in case you need it. DIAGNOSTIC AIDS The following can cause an intermittent condition: A short between the front end sensor signal and low reference circuits ; High or low resistance in the front end sensor signal and low reference circuits

How to fix code b0103 Chevrolet car?

How do I fix code B0103 CHEVROLET? Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. How much do you know about cars? The cost of diagnosing the B0103 CHEVROLET code is 1.0 hour of labor.

Where is the b0103 code on my Silverado?

Hey I have a 2004 Chevy Silverado 2500HD 6.0L and I went to the dealer and they scanned my truck and came up with the code b0103 front right impact sensor. I have looked everywheres including in the door panel and cannot find it.