How to reset your Chevy or GMC oil change light?

Here’s the easy way to reset the oil light on your Chevy or GMC. Oil lights have been a standard feature on Chevy and GMCs for years. Newer Chevys will have a built in Vehicle Information Center (VIC), but older models don’t. If your GMC is 2006 or newer, it comes with the GM Oil Life System.

How to reset PassLock reset system on Chevy?

1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine.

Is there a 4WD light on a 2000 Chevy Silverado?

Mine is a 2000 Silverado Z-71 Extended Cab. The part number is the longer of the two – 15709327. I believe they used this part for 1999, 2000, and 2001. You can purchase the part, APDTY 012173 4×4, Four Wheel Drive 4WD Transfer Case Selector Button Switch. Replaces GM Part Numbers 15709327, or 19168767, from amazon by clicking the link below.

How do you remove a 4 wheel drive light?

There are about a dozen points where it connects. Pop them off and pull the dash plate off. To remove the four wheel drive select switch there are little plastic locks on the top and on the right, hold them up and pull out. Turn the switch over and look for the part number on the back.

How to reset the service 4WD light and the ” change ” light?

To reset the Change Oil light turn the ignition on but do not start and then push the gas pedal 3 times. The Service 4WD light is most likely the 4WD switch on the dashboard. If the lights are acting funny then the switch needs to be replaced.

Is there a way to reset the oil change light?

If you’ve had your oil changed at an authorized dealer, the technician will reset the light as part of the service. If playback doesn’t begin shortly, try restarting your device.

Why does my 4WD light come on on my Chevy Silverado?

There is a common problem with 1999-2001 Chevrolet Silverado where the service 4wd light comes on in the vehicle. The light is scary and led me to believe there were major issues with my four wheel drive, but it turns out its a quick, cheap, and painless fix by swapping out the 4wd selector switch.

How to clear service engine soon light 1990 to 2002 Chevy?

If playback doesn’t begin shortly, try restarting your device. As an Amazon Associate I earn from qualifying purchases. I am a participant in the Amazon Associates Program, an affiliate advertising program designed to provide a means to earn fees by linking to Amazon and affiliated sites.

Do you reset the oil light when you change the oil?

Do not reset the oil light unless you have actually changed the oil. The light is there to tell you when it’s time to change the oil. Resetting the light without changing the oil may cause you to miss an oil change, which can damage your engine. Turn the car’s systems on, but leave the engine off.

How to reset the oil light on a Buick Enclave?

Press the MODE button until the DIC reads “Oil Life Left/Hold Set To Reset”. Press and hold the SET button until the display reads “100 percent”. You will hear 3 chimes and the “Change Engine Oil Soon” message will go off. Turn the key to the OFF position and back on to confirm reset successful.

How do you change the oil in a Chevy?

For second generation models (2007-2013): Step 1: Insert key into the ignition and turn the vehicle to the “ON” position. Do this without starting the vehicle. Step 2: Press the accelerator pedal to the floor three times within five seconds. The “CHANGE OIL SOON” light should begin to flash, which means the system is resetting.

When does the oil change light come on?

The oil change light is triggered when the vehicle has counted down the expected life of your oil to zero. If you’ve had your oil changed at an authorized dealer, the technician will reset the light as part of the service.

How do you turn off the oil light?

Sit in the driver’s seat with the doors closed. Insert the key into the ignition and turn the key to the accessory power position. All the lights will be displayed on your instrument panel. 2. Within five seconds of turning the key, depress the accelerator fully to the floor three times. 3. Watch for the oil light to flash and turn off.

How do you check the oil life on a Chevy?

Locate and press the VIC button. The VIC button will have an image of a road or the letter “i” on it. Repeatedly pressed the VIC button until “oil life” is displayed on the onscreen menu. 3. Press and hold the check mark button on the VIC for five to ten seconds until the oil life display reads 100%.

What happens if you don’t change the oil in your GMC?

Engine oil is responsible for providing necessary lubrication to vital engine components. If the engine oil is not changed at the recommended intervals, you could experience premature engine wear. Piston heads in your 2002 GMC are especially susceptible to wear if the piston rings become damaged from insufficient lubrication.

How do you reset the oil light on a Honda Accord?

While the oil life message is displayed, press and hold the Enter button on the Driver Information Center for one second. 3. The Driver Information Center will display a reset acknowledgement message. Turn the key to the off position. After you’ve reset the oil light, turn the key to the off position.

Why do you need an oil life monitor on a GMC?

Knowing when to change your oil is incredibly important, and the Engine Oil Life Monitor, found in most new GMC models, not only helps owners keep their GMC properly maintained, but also maximize their maintenance investment. An engine contains thousands of moving parts, like valves, pistons, camshafts, and so on.