How to replace multifunction switch in GMC Sierra?

1A Auto shows you how to repair, install, fix, change or replace a broken, damaged, faded, worn or faulty multifunction/turn signal stalk, high beam and wiper switch. This video is applicable to the 95, 96, 97, 98, 99 GMC Sierra

What to do if your key is stuck in the ignition switch?

The key may be stuck in the ignition switch, but that shouldn’t stop you from turning it. If you don’t have a key, you will need to force the module to turn using a flathead screwdriver. Press the release pin inside the hole on the ignition module with a screwdriver.

Where is the release pin on an ignition switch?

The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.

Where can I get an aftermarket ignition switch?

You can sometimes get aftermarket ignition switches from your local auto parts store as well. Squeeze the release pin on the ignition switch so it’s flush with the side. The same release pin that stopped the switch from coming out now needs to be pressed in so you can slide the switch into place inside the ignition module.

Where is the ignition switch on a 1997 GMC?

Disconnect the ignition switch from the vehicle wiring harness connector at the base of the steering column. Place your multimeter in Ohms mode. Place the ignition key in the ACC position. You should have continuity between terminals D2 and D6 of the ignition switch connector.

What kind of ignition switch does a 1997 Chevy Tahoe have?

This tutorial will help you test the ignition switch on the 1997 Chevrolet and GMC Pick Up, Suburban, Tahoe, and Yukon equipped with a 4.3L, 5.0L, or a 5.8L V8 engine. The ignition switch test involves checking for continuity across specific terminals of the ignition switches connector.

What was the ignition module for a 1996 GMC c2500?

1996 GMC C1500, C2500, C3500 Pick Up. 1996 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a misfire or a no-start problem (caused by the ignition coil, the ignition module, or the crankshaft position sensor).

How to diagnosis and repair a GM 4WD truck?

Check every function for response: 2HI, Auto4WD, 4HI, 4LO, Neutral. Pull the dashboard apart (it is just held with clips) and pull out the buttons. Disconnect both connectors. Using the DMM, measure the resistance between the innermost pins on both connectors. The resistance should be steady (no changes while the button is pressed).

When did my 2003 suburban 4WD system fail?

When my 2003 Suburban’s 4WD system failed, I was 4 hours from home with my travel trailer! The front axle was halfway engaged, so it produced a gut-wrenching grinding noise during turns for the entire drive home. However, I fixed it myself-and I bet you can, too!

What does the service 4WD light on a GM Truck mean?

The solid lights on the 4WD buttons are telling you where the transfer case encoder motor thinks it is, and blinks on the mode that it is trying to go to after you push the button. If it fails to move to the new position, it goes back to a solid light on the original position and illuminates the “SERVICE 4WD” light.

Why are my brake and turn signal lights not working?

Having issues with your taillights, brake and turn signal lights or reverse lights? All issues are covered here: fuses, bulbs, bad grounds, broken, burnt or pitched wires and bad connections. Keep your patience, watch the video and we can find it and fix it. Loading…

How to replace turn signal wiper stalk and Cruise switch?

Well, quite frankly, life just got in the way and our ‘show’ took a break for over 10 years. During that decade YouTube exploded and what we were once doing is now very commonplace. Recently we decided to bring it back, a little lighter and a little better quality.

Why is my turn signal wiper switch not working?

(Playback ID: JMvxNV_z0zZSF5O2) Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.

What kind of fuse box does a Lincoln Navigator have?

PCM relay coil, Speed control relay coil (2003-2004), SecuriLock transceiver, Heated PCV valve relay coil (2005-2006) 2003-2004: BSM (door locks, liftgate glass release relay), Liftgate glass release motor, Left front window motor, Door/Liftgate lock motors

What kind of solenoid does a Lincoln Navigator have?

A/C compressor clutch relay, A/C compressor clutch solenoid, Air suspension compressor relay (2003-2004), 4×4 Integrated Wheel Ends (IWE) solenoid

How long does it take to install a GMC malfunction switch?

The switch is and easy install and took me less then 1 hour to remove and install, if you have trouble just go to YouTube and type in 2005 GMC Malfunction Switch install, they show a Short Cut that saves you Hours and you DO NOT need to remove the Steering Wheel. Fixed bright lights with use of turn signal.

What kind of switch does a GM car have?

It is a complex switch that controls multiple functions such as the headlights, turn signals, cruise control, and windshield wipers on your vehicle. This original equipment combination switch has been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

What is an ACDelco original equipment combination switch?

An ACDelco GM Original Equipment Combination Switch is a GM-recommended replacement for your vehicle’s original component. It is a complex switch that controls multiple functions such as the headlights, turn signals, cruise control, and windshield wipers on your vehicle.

Where is the ignition switch on a GMC Jimmy?

If the mechanical assembly or contact points inside the ignition switch on your GMC Jimmy have worn out, you may have a hard time providing power to the ignition or electrical system, if at all. The switch on your Jimmy is mounted atop the steering column assembly, hiding under the dashboard.

How do you change the ignition switch on a car?

Remove the pin (if the new switch came equipped with it) from the switch slider by hand or with pair of needle-nosed pliers. Insert the key into the ignition lock cylinder; turn the key to make sure the rod is actuating the new ignition switch. Then turn the key back to the off position.

Where is the pin on the ignition switch?

Slide the ignition switch off the actuating rod and remove it from the steering column. Make sure the new ignition switch is in the off position. Some aftermarket switches will have a pin on the switch slider, close to the base of the switch, to lock it in the off position to ensure proper installment. Verify whether your new switch has this pin.

How to replace multifunction switch in GMC Sierra?