How to replace lower ball joint on Chevy Silverado?

This video outlines the complete process of removal and replacement of the upper control arm and lower ball joint on a 2008 Chevrolet Silverado 2500 HD 4X4 with torsion bar front suspension. The process is similar on many GM trucks and includes tips and tricks to help make the job easy and do it right. The entire process was unedited for time.

Why are my ball joints on my Chevy S-10 not working?

Worn ball joints on a Chevy S-10 cause alignment problems resulting in rapid uneven tire wear as well as banging noises when encountering rough surfaces. Severely worn ball joints can separate from their socket, which would result in total loss of steering.

How do you install a new ball joint?

Install the new ball joint up through the bottom of the lower control arm and tap it with a hammer gently to line it up so that it will be pressed in perfectly straight. Press the ball joint in the lower control arm using the ball joint installer kit. Make sure the joint is completely in before removing the installer.

How do you replace a worn ball joint on a Chevy S-10?

By raising each tire off the ground about 3 inches and prying up from underneath the tire, a worn ball joint can be detected by the free-play experienced when lifted. Raise and support the side of the vehicle that the service is to be performed on using a jack stand. Remove the wheel with the lug wrench.

How to replace a steering knuckle hole in a soccer ball?

Guide the new joint through the knuckle hole. Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from. 2 Bolt the joint into place using the hardware included.

What’s the difference between upper and lower ball joints?

1. Premium Polychloroprene Sealed Boot w/ Grease-Relief Valve: 2. Powdered-Metal Gusher Bearing Technology: 3. Full-Ball Hardened Stud w/ Grease Grooves: 4. One-piece Forged Housing: 5. Belleville Washer Pre-Load: 6. Greaseable Design: 7. Pressed-in Patented Cover Plate Design loading… loading…

What happens if a ball joint fails on a Chevy Aveo?

If a ball joint fails, the suspension can collapse, causing a loss of control of the vehicle. Depending on the suspension design, ball joints can be found either in the front or the rear. The vehicle may need to be taken to a shop for wheel alignment after this service. Mobile mechanics do not have the machinery to align wheels. Remove the wheels.

Where are the ball joints on a car?

The ball joint connects the control arm to the steering knuckle. As the wheels – and therefore the steering knuckles – move, the ball joints help the suspension – and therefore the control arm – stay steady.

What are the symptoms of a ball joint replacement?

What common symptoms indicate you may need to replace the Ball Joint Front? 1 Clunking noise from front tires. 2 Steering wheel shakes. 3 Car moves to the right or left, especially going over the bumps. 4 Vehicle tires have abnormal wear.

Where to get front lower ball joints for Chevy Silverado 1500?

At DST we want you to be able to get your Chevrolet Silverado 1500 back on the road quickly and confidently. If you have any questions about Front Lower Ball Joints or for your Chevrolet Silverado 1500, just give Moog-Suspension-Parts.com tech support guys a call directly at 888-406-2330.

How much does it cost to replace a suspension joint on a Chevy Silverado?

The average cost for a Chevrolet Silverado 1500 suspension ball joint replacement is between $331 and $389. Labor costs are estimated between $221 and $279 while parts are priced at $110. This range does not include taxes and fees, and does not factor in your specific model year or unique location. Related repairs may also be needed.

Is there free shipping on front lower ball joints?

Enjoy fast, free shipping on any Front Lower Ball Joints that you purchase for your Chevrolet Silverado 1500 if the order is over $119. Additionally, DST takes the manufacturer’s warranty a step further.

What are the ball joints in a car?

Ball joints are part of the suspension system, and consist of a ball and socket that’s encased in a lubricant-filled rubber boot. They link the steering knuckle (which supports the wheel hub, bearing and wheel) to the lower and upper control arms.

Do you need to replace the ball joint on your car?

On the first alignment, the tech said I needed to replace the lower ball joint on the passengers side, and both of the upper ball joints. I said ok, I will take it home and change it out and bring it back.

When did the lower ball joint on my Dodge truck get replaced?

The lower ball joint on the passengers side was just replaced a few months ago at 225,000 miles. It to was the original that came on the truck in 1997. My daughter has an 08 Dodge 1500, with 125,000 miles. She took it to have the front end aligned and they told her the same thing they told you.

Which is the best shop for ball joint replacement?

Moog is about the best there is. I just got back from having my truck aligned, for the second time in less than 3 months, because the last shop did not do a proper job. Some shops push there mechanics to put out as much work as they can in a day in the interest of making money.

When to replace upper control arm ball joint?

2007 and up you have to replace the whole upper a-frame. Negative, Ghostrider – upper balljoints are available at Oreilly for $28.99. Enjoy That’s a 2007 Classic….All NNBS require replacement of the entire upper arm, just for the ball joint.

How to replace the upper wheel on a Chevy Silverado?

Tighten the ball joint to the hub assembly. Proceed to install the strut assembly along with the stabilizer link, and mount the wheel. Hand-tighten the lug nuts and use the 18mm socket to finish mounting the strut tower to the chassis.

How to replace the lower suspension on a Chevy Silverado?

Begin by pulling the hub assembly outwards, so all the suspension components can easily be accessed. Loosen the stabilizer link nuts by placing a wrench on top and a socket on the bottom. Remove the two 15mm bolts that hold the strut tower in place from the lower control arm. Remove the strut tower assembly. Figure 4.

How to replace a damaged control arm on a Chevy Silverado?

The following instructions detail how to replace a damaged control arm on your Chevy Silverado. While the truck is on the ground, break loose the lug nuts. Use a jack to safely lift the truck. Rest the chassis on the jack stands. Finish removing the lug nuts and wheel. Figure 1. Remove the wheel.

How do you heat the back of a Chevy Silverado?

To heat only the seatback, press the vertical button with the heated seatback symbol. An indicator light on the seatback button will come on to designate that only the seatback is being heated. Additional presses of the seatback button will cycle through the heat levels for the seatback only.

What’s the name of the company that makes the Chevy Silverado?

This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice. For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division whenever it appears in this manual.

When to replace the lower control arm on a Silverado?

However, if the ball joint has failed, the lower control arm needs to be replaced because this ball joint is not serviceable. Figure 1. Replacement lower control arm for a first generation Silverado 1500. Traditional “wishbone”-type, “A”-shaped front suspensions utilize an upper and lower control arm.

How to replace the lower wheel knuckle on a Chevy Silverado?

Lift lower control arm to free the knuckle from the ball joint’s threaded stud. While lifting up the wheel knuckle, lower the jack, and then pull the wheel knuckle out and away from the lower control arm. Figure 21. Pull away detached wheel knuckle from the lower control arm.

Where to remove lower control arm nut on Chevy Silverado?

Remove the already-loosened 24mm nut at the bottom of the wheel knuckle. This nut holds the lower control arm ball joint to the knuckle via its threaded stud. With the jack still in place, remove the 35mm wheel nut and the washer behind it from the center of the hub.

How do you replace a front axle ball joint?

1. Remove the automatic locking hub, hub-and-disc assembly, and spindle components. 2. Remove the steering arm. 3. Remove the cotter pin from the upper ball joint castle nut. 4. Remove the retaining nuts from the upper and lower ball sockets. 5.

How to replace a lower control arm ball joint?

Replacing a Lower Control Arm Ball Joint. Learn how to replace a lower ball joint by pressing it out of the control arm and pressing the new one back in. To watch the longer, in depth version, click the link below. Press out a Ball Joint (In-depth):

Do you need to remove steering arm before ball joint replacement?

The non-hardened threads in the yoke can be easily damaged by the hardened threads in the adjusting sleeve if caution is not used during knuckle removal. – On the LH knuckle, it is necessary to remove the steering arm before servicing the upper ball joint. Remove the lower ball joint snap ring before beginning.

How do you replace ball joints?

How to Change a Ball Joint in a Car Step 1 – Lift Car Step 2 – Remove the Caliper on the Brakes Step 3 – Remove the Brake Discs Step 4 – Remove Ball Joint Nuts Step 5 – Separate Ball Joint from Hub Carrier Step 6 – Remove Ball Joint Step 7 – Grease New Ball Joint Step 8 – Add New Ball Joint In Step 9 – Take Car Down

How much does it cost to repair a ball joint?

There are also two joints per each wheel. If you want the basic parts for a do-it-yourself ball joint replacement, it may cost around $35 to $75 per ball joint or $130 to $300 for four. If you want the basic parts for a do-it-yourself ball joint replacement, it may cost around $35 to $75 per ball joint or $130 to $300 for four. If you own a high-end or luxury vehicle, it can cost you more.

How do you replace upper ball joint?

Bolt the Ball joint to the hub first and then to the A arm. Put a small jack under the geared hub and raise it until the new ball joint bolt is through the upper geared hub hole. Hand tighten the slotted nut. Line up the new ball joint and drop the 4 bolts and washers into the holes. Tighten the bolts to 37 ft-lbs.

Do ball joints just break?

Ball joints can even break if they’re in poor condition. The joint can either break by detaching from the socket or the socket itself can break. Either type of break can cause serious, expensive damage to your car or truck. If a ball joint breaks, your wheel is free to move in any direction.

How do you know if ball joints need to be replaced?

Inspect the ball joints to make sure they need to be replaced. Figure out if your vehicle’s got a strut-style suspension or a control arm, then check the ball joint by either jacking up the control arm near the ball joint to check for wheel play, or by jacking up the car and using a pry-bar to check for wheel play in a strut-style suspension.

How do you put a new ball joint in a car?

Slide the new rubber boot over the ball joint’s stud and guide the new ball joint back up through the steering knuckle hole, where it came from. Bolt the joint into place using the hardware included.

What kind of ball joints does Dana Spicer make?

DANA SPICER and AAM American Axle Manufacturing Ball Joint Sets include everything you need to do one side of your truck. Replace your old worn out parts with the very best replacement ball joints on the market.

When do you need to replace ball joints in a car?

Modern ball joints are sealed, while this prevents dirt, grit and other impurities from damaging the joint, it also prevents maintenance. This means that if you have a problem with your ball joint, the entire assembly will usually need to be replaced. Depending on the type of suspension, most cars have both upper and lower ball joints.

What does it mean when your ball joints are not working?

Grasp the top and bottom of the tyre and rock it in and out along the wheel’s vehicle axis. If the ball joints are working well, there should be little to no play in this movement. Noise and play from the top – this indicates a problem with the upper ball joint. Noise and play from the bottom – this suggests a problem with the lower ball joint.

How is the best way to check your ball joints?

Checking your ball joints when driving is straightforward, simply: 1. Take your car out for a drive Drive the vehicle on a public road at the speed limit and pay close attention to the engine, steering and overall performance of the car.

What causes the ball joints to wear out faster?

Depending on the type of suspension, most cars have both upper and lower ball joints. The lower ball joints are usually larger and wear out faster due to the weight of the front of car that rests on them. Click here to read our detailed article on ball joints.

Why are the ball joints on my car clunking?

Clunking noises are caused by the worn ball joints rattling as the suspension travels up and down over the road. The squeaking noise is caused by the rubber boot that protects the grease inside the ball joint is damaged, the ball joint will start to squeak. These noises will get louder the more worn the ball joints become.

How do you know if ball joints need to be replaced?

Is there a 2014 Ram for lower ball joint replacement?

2014 Ram 1500, Lower Ball Joint Replacement and Upper A-Arms! STEP-BY-STEP! If playback doesn’t begin shortly, try restarting your device.

How much does it cost to replace a ball joint on a car?

After ball joint replacement the alignment does need to be re-done. On average, it costs about $300 to replace a ball joint on a passenger vehicle. It costs about $500 on average to replace a pair of upper and lower ball joints (one side) on a four wheel drive vehicle.

Ball joints are a part of your vehicle s suspension system that connect the steering knuckles to the control arms. Purchased OEM Motorcraft lower ball joint for 2004 Ford with 155K miles. Autozone loaned me the ball joint removal tool and torque wrench. very involved but doable for the average DIY.

How many ball joints are in a front suspension?

There are usually four ball joints in a car’s front suspension, with an upper and lower one on each front wheel. “ New upper and lower ball joints, tie rod ” ( CC BY 2.0 ) by | El Caganer – Over 6 Million views!

How much does it cost to replace ball joints on a Jeep Grand Cherokee?

For a 2000 Jeep Grand Cherokee four wheel drive, which uses a solid front axle, the labor time to replace the upper and lower ball joints on one front corner is 1.9 hours. A factory pair costs about $150, and a pair of Delphi ball joints costs about $63. This makes the job about $440 using OE parts, or about $353 using aftermarket parts.

How much does it cost to replace ball joint on Honda Civic?

For A 2003 Honda Civic, the labor time to replace the front lower ball joint is 2 hours. It’s pressed into the knuckle, which is usually removed for the service. A factory part costs about $65, or a Mevotech part costs about $35.

Where are the ball joints on a front wheel drive vehicle?

One the front suspension of a vehicle when you steer, the front knuckles pivot between two points at each front wheel. For an independent front suspension vehicle, those two pivot points are the upper and lower ball joints. Solid axle four wheel drive vehicles also use upper and lower ball joints on each front corner as pivot points for steering.

How many ball joints do you need to replace?

IMO the shops you are dealing with probably want to do all 4 ball joints, because one or two are bad, and they have to warranty there work, so it may be there policy to do all 4 if two are more are bad. Click to expand… exactly. On my last truck a 96, the original ball joints lasted 250K miles.

How often should you change the oil in your car?

It used to be normal to change the oil every 3,000 miles, but with modern lubricants most engines today have recommended oil change intervals of 5,000 to 7,500 miles.

Why do I need to replace my front ball joint?

In addition, some ball joints have rubber dust covers that, if torn, can allow dirt and water in. That can damage the joint. Front ball joints connect the suspension control arms to the steering knuckles.

When do load bearing ball joints wear out?

They often last more than 100,000 miles but can wear out earlier if driven frequently on rough roads, which puts more stress on the suspension. Load-bearing ball joints that carry the weight of the vehicle tend to wear out sooner than those that aren’t load-bearing.

Where are the ball joints on the steering wheel?

Front ball joints connect the suspension control arms to the steering knuckles. Their ball shape allows the suspension to move up and down and the wheels to pivot when you turn the steering wheel.

What do you need to know about car ball joints?

Some ball joints have wear indicators, but others have to be checked by raising the car off the ground and seeing if the wheels allow excessive play. In addition, some ball joints have rubber dust covers that, if torn, can allow dirt and water in. That can damage the joint.

What are the symptoms of a bad suspension ball joint?

1. Clunking Noises From the Front Suspension One of the most common symptoms of a problem with suspension ball joints is clunking noises coming from the vehicle’s front suspension. As ball joints wear out they become loose in the socket and rattle and knock as the suspension travels up and down over the road.

Where can I get a replacement ball joint?

If necessary, they will be able to replace any failing ball joints for you. The most popular service booked by readers of this article is Suspension Inspection. Yourmechanic’s technicians bring the dealership to you by performing this job at your home or office 7 days a week between 7AM-9PM.

Why are ball joints important to a vehicle?

Because ball joints are an important component of any vehicle’s suspension. When they begin to have problems or fail, the overall handling and ride characteristics of the vehicle are likely compromised.

How does the ball joint work on a Tahoe?

How much does a ball joint replacement cost?

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. Chevrolet Silverado 2500 HD Ball Joint Replacement (Front) costs $222 on average. What is the Ball Joint Front all about? Ball joints are a part of your vehicle’s suspension system that connect the steering knuckles to the control arms.

What happens when a ball joint fails in a car?

Loose joints can also cause suspension noise (typically a “clunking” sound when going over a bump). If a ball joint fails, the suspension can collapse, causing a loss of control of the vehicle. Depending on the suspension design, ball joints can be found either in the front or the rear.

How to replace upper control arm ball joint?

Upper Ball Joint Replacement. This video will show you how to replace the Upper Control Arm Ball Joint on a Chevy Trailblazer, GMC Envoy, etc. Replacing a ball joint is fast and easy and can be done with basic hand tools and a ball joint press you can rent for free at your local parts store.

Purchase the correct replacement ball joint assembly for your vehicle. Go to the auto parts store and get a replacement part appropriate for your make and model. All you’ve got to know is the type of vehicle and you should be able to use the guidebook in the aisle, or ask for help and they’ll be able to direct you.

How much does it cost to replace a ball joint on a jeep?

How long does it take to replace a ball joint on a 1997 Chevy k1500?

For a 1997 Chevrolet K1500 four wheel drive with torsion bar suspension, the labor time to replace the front ball joints on one corner is 4 hours. This has an independent suspension, but has the disadvantage of the original ball joints being held in by heavy rivets, which must be cut and driven out.

How much does it cost to replace a ball joint on a jeep?

How can I check the ball joint on my car?

Figure out if your vehicle’s got a strut-style suspension or a control arm, then check the ball joint by either jacking up the control arm near the ball joint to check for wheel play, or by jacking up the car and using a pry-bar to check for wheel play in a strut-style suspension.

How do you replace a ball joint on a truck?

Trucks and some cars – separate the steering knuckle from the ball joints with a ball joint fork and set aside. This process usually requires a lot of force and a BIG hammer! Carefully inspect and remove any snap rings that may be securing the ball joint in place. Using a ball joint press, press the old joint out of the control arm.

Do you need to replace all ball joints at the same time?

Usually, mechanics include an alignment when replacing ball joints. What you should know is that you do not need to replace all the ball joints at the same time. In fact, your car can run properly even if you just replace the ones that are faulty.

Can a ball joint be removed from a steering knuckle?

In most cases, a ball joint press and ball joint fork will be needed to remove the ball joint and separate the control arm from the steering knuckle, which both of these are available for free through AutoZone’s Loan-A-Tool program. For ball joints that are bolted on, simply unbolting the bolts will separate the joint from the control arm.

Can a CV axle be replaced with a ball joint?

To replace or perform repairs on or near the ball joint such as replacing a control arm or a CV axle the ball joint will need to be undone which means taking the nut off of the joint and applying pressure while striking the spindle or control arm bulk head with a hammer.

How do you remove the ball joint from a lawn mower?

Removing the Old Ball Joint Pull the cotter pin and loosen the large castellated nut. The top should look like a crown, or castle, at the bottom. Pop loose the ball joint. The goal is to try to guide it through the hole in the upper half of the steering knuckle. Remove the allen bolts and slide the control arm free.

How can I check the ball joint on my front suspension?

If your front suspension uses MacPherson struts, look for a wear indicator, which is usually a grease fitting. Grasp the fitting and try to wiggle it. If the fitting moves around inside the housing, you’ll need to replace the ball joint. Jack up the car on the front cross-member.

What happens when a ball joint loosens in a car?

If a ball joint starts to loosen, you’ll hear clunking sounds from the front as the joint rattles in the socket. If it tightens up, the steering will bind so you can have a stiff spot as you turn the steering wheel. There may be a binding or squeaking sound in addition to the stiff spot.

How much does it cost to replace a ball joint?

One ball joint takes about one hour of labor to replace. One hour of labor at a Toyota dealership is approximately $90.

How to replace a lower ball joint on a Chevy 1500?

1. Remove the cotter pin and ball joint nut. 2. Using the ball joint separator and a large hammer, separate the hub assembly from the lower control arm. 3. I used a cargo strap to hold the upper control arm, rotor, and hub assembly out of the way while working on the ball joint. Step 4: The Workout!

How much does a GMC Sierra ball replacement cost?

GMC Sierra 1500 Ball Joint Replacement (Front) at your home or office. Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing. Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. GMC Sierra 1500 Ball Joint Replacement (Front) costs $274 on average.

GMC Sierra 1500 Ball Joint Replacement (Front) costs $270 on average. What is the Ball Joint Front all about? Ball joints are a part of your vehicle’s suspension system that connect the steering knuckles to the control arms.

When did GM replace the ball joint on my truck?

My 97 C1500 with 226,000 miles still has its original lower ball joint on the drivers side. Why would all 4 god bad at the same time? The lower ball joint on the passengers side was just replaced a few months ago at 225,000 miles. It to was the original that came on the truck in 1997.

How much does it cost to replace a ball joint?

Dealer said lower right is bad but the left should also be replaced. ~ $1300. my 2000 with 169K miles has the same issue. Dealer said lower right is bad but the left should also be replaced. ~ $1300.

How to tell if a ball joint is bad?

Learn how to diagnose a bad ball joint for both an upper and lower control arm. I also quickly show you how to tell if it is a bad tie rod, bushings, or a bad bearing just in case your ball joint is not bad. A bad ball joint will make noise which is the first symptom of knowing it’s bad.

What happens when you change the ball joint on a truck?

In the end a slight misalignment is corrected because at the end, the joint is pressed flush, bringing it into alignment, and besides, the joint is there to give flexibility. Your ball joints now officially installed and tightened…

How do you change the ball joint on a truck?

2: Loosen the castle nuts. You can remove them all the way but rethread them on the joint just a few turns. The reason you leave the nuts in place is to keep the knuckle assembly from flopping around. 3: Place your Ball Joint Separator between the bottom of the steering knuckle and the ball joint.

How do you remove ball joints from steering knuckle?

To break the ball joints free from the steering knuckle you’ll need a pickle fork type ball joint separator (27020) and a pickle fork type tie rod end separator (27025). Remove the 18MM nut from the tie rod end and separate it using the separator and a sledge hammer.

What kind of ball joint does Chevy Tahoe use?

FYI the ’97-’99 uses a stamped lower control arm with a high press force design ball joint. GM sweetened the pot by using green Loctite on the lower ball joints so they are tight. I picked up the ball joint service loaner kit from Advance Auto as it had 4x the adapters than Auto Zone’s kit.

How do you replace ball joint on McPherson strut?

Leave the castellated nut in place, just a few turns in to keep it in a safe place. If you’re working on a McPherson strut suspension remove the “pinch bolt” that clamps the ball joint stud. Pop loose the ball joint.

Where did the 2013 Chevy Silverado 1500 come from?

No accident or damage reported to CARFAX. 1st owner purchased on 12/26/12 and owned in PA until 12/31/19 • 2nd owner purchased on 03/13/20 and owned in PA until 02/05/21. 1st owner drove an estimated 6,383 miles/year • 2nd owner drove an estimated 0 miles/year.

When is ball joint replacement for GMC Sierra 2500?

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. See availability customer ratings (64) Ball Joint Replacement (Front) Estimate for GMC Sierra 2500 HD

How much does it cost to replace a front ball joint?

2018 GMC Sierra 2500 HDV8-6.0L Service typeBall Joint Front – Upper Right Replacement Estimate$192.47 Shop/Dealer Price$230.39- $306.35 2011 GMC Sierra 2500 HDV8-6.0L Service typeBall Joint Front – Upper Left Replacement Estimate$180.47 Shop/Dealer Price$216.49- $291.03 2012 GMC Sierra 2500 HDV8-6.6L Turbo Diesel

How many ball joints do you need to replace?

Click to expand… They had to replace to upper and lower ball joint and tie rods and the driver side axle and some other parts on the drivers side and just the ball joints on the passenger side and a wheel alignment I am goin to pick it up tomorrow or Friday and will see what exactly what was replaced and how much the bill is.

How to replace upper and lower ball joints?

This video outlines replacement of the upper and lower ball joints on a 2000 GMC Savana van. This GM G3500 van is a rear wheel drive vehicle with a coil spring type front suspension. This process is identical to the Chevy Express 3500 van as well. Watch this video for more information. Loading…

How to find ball joints in GM Genuine Parts?

No results found for ” ball joints, ball joint “. Here are some helpful search tips: Search by a part name. Example: water pump. Be less specific. Example: brake instead of ceramic brake. Remove information such as make, year or model. Can’t find the part you are looking for?

What kind of ball joint does a Chevy Equinox have?

Upper ball joint. With premium opt. With performance pkg. With performance suspension. Description: Equinox, Terrain. Description: Without crew cab. All models. 1/2 ton. 2wd, 1/2 ton, std & extended cab. Exc.High Performance Suspension.

What makes up the lower ball joint in a car?

The lower ball joint is what attaches the steering knuckle and control arm together. There are two pieces which make up the lower ball joint; a socket and ball.

What makes up the lower ball joint of the steering knuckle?

The lower ball joint is what attaches the steering knuckle and control arm together. There are two pieces which make up the lower ball joint; a socket and ball. These pieces are inside of a rubber boot that is filled with lubricant.

How to replace lower ball joint on Chevy Silverado?