How to replace ignition switch on 1993 Chevy S-10?

With the right hand hold the key in the “Start” position and with the left hand slide the switch until the starter engages. As soon as this happens, release the key and tighten the nuts on the ignition switch. Try the key one more time to assure proper adjustment. Raise the steering column.

How does the starter work on a Chevy S10?

The starter on a Chevy S10 pickup truck is a motor that works with the ignition switch and the battery to generate power to ignite the engine. If you need to change the starter, this will be done from within the engine compartment.

What are the best parts for a 1993 Chevy S10?

Classic Industries is America’s first choice for 1993 Chevrolet S10 parts and accessories. MOMO Combat EVO shift knobs combined with a variety of materials and finishes make the MOMO Combat Evo the perfect choice for any taste. They feature top grain black leather cover with silver stitching and chrome insert. A…

How do you replace the alternator on a Chevy S10?

Reconnect the secondary cable to the alternator by reengaging the nut. Pull back the tab from the primary cable, and then reconnect that wire. Push the wire in until the tab locks. Rotate the belt tensioner counter-clockwise once again. Replace the serpentine belt, referring to the routing guide, which is affixed near the radiator.

How do you remove a steering column cover?

Remove the lower panel cover under the steering column, using the appropriate socket to remove the bolts. Remove the three 15 mm bolts from the steering column support bracket, using a socket. Allow the column to drop down to the point where the steering wheel is resting on the seat.

When do you need a C10 ignition switch?

When it has trouble starting, here are a few possibilities, but when the starter does not even try to engage, that means you need a new Chevrolet C10 Pickup ignition switch from AutoZone. C10 Pickup ignition switches transmit the power you need from the battery to the starter when you turn the key in your ignition.

What should I do if I need to replace my ignition switch?

Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.

What happens when the ignition switch is off?

Generally speaking, in the “OFF” position, the ignition switch doesn’t connect anything; in the “ACC” position, the radio or fan may be energized; in the “RUN” position, the engine control module is energized; and finally, in the “START” position, the starter relay is engaged. (These generalizations, depend significantly on year, make, and model.)

Is there a way to remove the C10 ignition switch?

C10 Ignition Switch Removal And Install, HOW TO VIDEO If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.

Which is the best ignition switch for a Chevy c1500?

When your key no longer starts your C1500 or even engages the starter, then a Chevrolet C1500 ignition switch from AutoZone is just what you need.

Do you have to take steering wheel out to replace ignition switch?

Take the steering wheel out if it’s in the way. In some vehicles, you may be able to replace the ignition switch without removing the steering wheel. However, if you’re unable to get access to the top of the ignition switch with all the interior trim pieces removed, the steering wheel may need to come out.

When to replace ignition switch in Chevy Tahoe?

1995-1998 GMC/Chevy pickup, tahoe, blazer, suburban, etc. ignition switch replacement. If you’re truck won’t start, the gauges aren’t working, or you have random transmission problems, the ignition switch could be at fault. This is a step by step tutorial on how to fix a broken ignition switch. Loading…

What’s the Accessory position on an ignition switch?

Insert the key and turn it to the “accessory” position. The ignition switch needs to be set to the accessory position before you can release it from the ignition module. The “accessory” position is before the starter is engaged, and would normally let you run the vehicle’s electronics without the engine running (when the battery is connected).

What’s the best way to remove an ignition switch?

Remove them carefully by either popping them off of their plastic clips or removing the screws and bolts that hold those pieces in place. Refer to a vehicle specific repair manual for guidance on how best to gain access to the ignition switch. Set all trim pieces aside somewhere safe where they won’t get stepped on or damaged. Helpful?

When does the ignition switch need to be set?

The ignition switch needs to be set to the accessory position before you can release it from the ignition module. The “accessory” position is before the starter is engaged, and would normally let you run the vehicle’s electronics without the engine running (when the battery is connected).

When your key no longer starts your C1500 or even engages the starter, then a Chevrolet C1500 ignition switch from AutoZone is just what you need.

How do you remove a battery from an ignition switch?

Use an appropriate sized wrench to loosen the nut holding the cable on the negative (-) terminal and then slide it off the post. You don’t need to remove the positive cable from its terminal. Tuck the negative cable to the side of the battery to make sure it doesn’t accidentally come into contact with the terminals.

Is the ignition lock on a 1997 Chevy Blazer?

The ignition lock cylinder and ignition switch in your 1997 Chevrolet Blazer work together as a single assembly. Still, you can replace the faulty switch as a separate unit from its housing.

How do you replace the ignition switch on a car?

Make sure you have all the required tools to replace the switch before you start. Insert the ignition key into the lock cylinder and turn the key to the “On” position without starting the engine. Then align the front wheels so they point straight ahead. Turn the ignition switch off and remove the key from the lock cylinder.

Where are the gears on an ignition switch?

Look at the gears on top of the old ignition switch. The gears on the new ignition switch should be in the same position before installation. Plug in the electrical connector to the new ignition switch and insert the switch into the cylinder housing until the switch tab snap into the slots of the lock cylinder housing.

How do you change ignition switch on S-10?

Remove the remaining 8-mm stud that attaches the ignition switch to the steering column. Lift the switch off the push rod that is inserted into a hole in the bottom of the switch. Lay the switch aside. Install the new switch onto the push rod, and secure it to the steering column using one of the 8-mm studs.

The ignition lock cylinder and ignition switch in your 1997 Chevrolet Blazer work together as a single assembly. Still, you can replace the faulty switch as a separate unit from its housing.

Why are my ignition switches not working on my Chevy S10?

If the connectors are blocked by the grime and grit that have built up over years of hard use, you’re apt to experience a truck that simply refuses to work. AutoZone offers assistance to those looking to replace their S-10 ignition switches by providing free advice via their professional, trustworthy staff.

How do you remove ignition switch from car?

Insert a straightened out paperclip into the slot just to the left of the key cylinder. This will lock the cylinder from starting. Inserting your screwdriver into the cylinder and turn it as far as you can to the right. Pull on both the paperclip and the screwdriver to gently slide the switch out of its current position.

How do you replace an ignition switch on a car?

Installing a Replacement Squeeze the release pin on the ignition switch so it’s flush with the side. The same release pin that stopped the switch from coming out now needs to be pressed in so you can slide the switch into place inside the ignition module. Slide the ignition switch into its hole.

What to do if your key is stuck in the ignition switch?

The key may be stuck in the ignition switch, but that shouldn’t stop you from turning it. If you don’t have a key, you will need to force the module to turn using a flathead screwdriver. Press the release pin inside the hole on the ignition module with a screwdriver.

What happens if you have a faulty ignition switch?

A faulty ignition switch in your vehicle can cause several problems ranging from your car stalling and all lights going dark to the radio not working unless the key is wiggled from side to side.

Where is the release pin on an ignition switch?

The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.

Can a faulty ignition switch cause a no start?

Please try again later. GM Ignition switch replacement to fix a no start or intermittent start. Faulty ignition switch contacts can also cause the PassLock system to enable Click here to see step by step proceedures. http://www.thejunkmanadv.com/the-junk… Support the site, buy service manuals here : http://www.tkqlhce.com/click-7357719-…

Where is the detent spring on an ignition switch?

Insert the key into the ignition switch and turn it to the left so it is in position one–the accessory position. Depress the detent spring (inside the small hole at the top of the cylinder) with the screwdriver and remove the cylinder and key.

How do you replace the ignition key on a car?

Pull the ignition key and lock cylinder out of the housing together. Install the replacement cylinder with its key inserted into the housing, making sure its retainer aligns with the retainer slot in the housing; the cylinder needs to be installed in the “Start/Run” position. Push in the cylinder so the retainer snaps into position.

How to replace ignition switch on 1993 Chevy S-10?