How to repair the ABS and speed sensor in a Dodge Dakota?

Learn how to read diagnostic trouble code to evaluate trouble indicators and fix broken sensors. So if your speed sensor or ABS brake system are on the fritz in your Dodge Dakota truck, watch this video and learn how to check and fix them. Want to master Microsoft Excel and take your work-from-home job prospects to the next level?

Is the Dakota digital speedometer compatible with GPS?

All Dakota Digital speedometers are GPS-Ready, meaning they are prepared for connection with a GPS speed sensor, such as our GPS-50-2, allowing any speedometer to utilize GPS technology.

How do you fix a speedometer transmission cable?

Align the slot end of the cable to the inside of the gearbox or transmission housing, turning the opposite end of the cable with your fingers until the slot seats. Connect the gearbox-transmission side of the cable housing, turning the retaining nut clockwise until it seats.

Where is the speedometer located on a car?

The speedometer cable translates the transmission gear speed through a cable housing and up to the speedometer gauge in the back of the instrument cluster. Connected at both ends by two small gears (or slots), the speedometer cable rotates within the housing and tabulates the speed of the vehicle.

How do you change the gear on a speedometer?

Clip the new driven gear into place on the speedometer cable. Replace the gear housing cover and secure it in place with the bolt you removed in Step 1. Secure the speedometer cable back into position. Determine the distance of the test drive needed to recalibrate your speedometer.

How do you calibrate a car speedometer?

Press and hold the calibration button on the speedometer, start the vehicle and release the button. Press the button again and drive the distance prescribed by the speedometer manufacturer. Press the button a third time after you have driven the designated distance.

What to do if your speedometer reads other than 60?

Set speedometer switches 2 6 7 8 OPEN, all others closed. Drive vehicle at 60mph. If the speedometer reads other than 60, set switches per chart below. Speedometer Reading OPEN SWITCH Speedometer Reading OPEN SWITCH

What causes the speedometer to go off when you change a tire?

Changing the stock parts, including the vehicle’s tires, can throw off the speedometer calibration; larger tires cause the speedometer to read a speed slower than the vehicle’s actual speed while smaller tires cause the speedometer to read a speed faster than the vehicle’s actual speed.

How do you remove a wheel speed sensor?

Once it is visible, you can remove the bolt that holds the sensor onto the hub/knuckle. Next, remove any clips or hold downs that are securing the sensor wiring to the vehicle’s chassis/body. Once you have done that, unplug it so you can remove it completely from the vehicle.

Where is the speed sensor on a truck?

ABS speed sensors are most commonly mounted at the wheels on most modern vehicles. This is the most efficient spot to mount them. Some older vehicles, trucks with solid axles in particular, will have them mounted on the rear differential.

When to replace the speedometer in your car?

If you notice that the speedometer does not work any longer, replace the vehicle speed sensor as it is the most likely cause. It is important to make sure that you purchase the correct vehicle speed sensor for your car.

What to do if your speed sensor is on the Fritz?

So if your speed sensor or ABS brake system are on the fritz in your Dodge Dakota truck, watch this video and learn how to check and fix them. If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.

How do you replace a speed sensor on a car?

Disconnect the sensor’s electrical connector. Place a drain pan beneath the sensor to catch any transmission fluid that may drip out. Remove the sensor and O-ring seal using a metric socket and a ratchet. Install a new O-ring seal on to the new speed sensor. Install the sensor into the transmission using a ratchet and metric socket.

Where is the transmission speed sensor located on a car?

Place wheel chocks behind the rear wheels. Raise the front of the vehicle using an automotive jack and support it with jack stands. Crawl underneath the vehicle and locate the transmission speed sensor; it protrudes from the rear-left side of the transmission’s tailshaft housing and has a two-wire connector attached to it.

How can I tell if my speedometer sensor is bad?

On most cars sold today, this will be indicated by the cruise control light being illuminated on the dashboard – even if it’s not engaged. If you experience this problem, it’s possible that the speedometer sensor needs to be replaced. 3. Check Engine Light comes on

Why is the ABS light and brake light not working?

I have a 1998 Dodge Ram 1500 Both the ABS light and the brake light are on. Changed the Speed sensor on the differential it didn’t help. I did replace the RWAL/ABS fuse and now the speedo works. Next I’m checking the front wheel sensors after that idk what to try. Any advise would be helpful. I have a 99′ Dodge RAM 2500.

How does the speedometer work on a Dodge Dakota?

The VSS is one part of a system of sensors that helps keep you safe (traction control, ABS, cruise control). A modern vehicle’s speedometer takes the input from the Vehicle Speed Sensor and sends that data to the ECU. The ECU is programmed with your Dakota’s gear ratios and stock tire height.

What to do if your speedometer is not working?

Instrument panel first. If your Dodge Dakota’s speedometer is not working, the first place to go would be to check the service engine soon light (if applicable). Now, take it out and see if the cruise control still works. If it does, that’s a pretty good indication that the vehicle speed sensor is just fine.

Why is the ABS not working on my Dodge Ram?

Any advise would be helpful. I have a 99′ Dodge RAM 2500. It started to not clear ABS and Airbag lights upon startup (go off for a second and then relight. Then if you try to operate truck, the speedometer would not work (no ODO on mine).

Where is the speed sensor on a Ford?

Slide under the vehicle and locate the speed sensor. On a Ford transmission, the sensor is located on the driver side of the transmission, toward the rear of the unit. The sensor is a magnetic unit that screws into the transmission and has an electrical connector plugged into it.

How do you install a new speed sensor?

Install the new speed sensor. Place the sensor into the appropriate spot on the transmission. Secure the sensor by twisting it clockwise with the wrench until the sensor cannot be twisted any more. Plug the electrical connector into the new sensor until it clicks into place.

How do you remove a transmission speed sensor?

Remove the mounting bolts to the speed sensor. Unplug the harness from the sensor. Note: The mounting bolts that secure the drive shaft to the rear axle may have hex, allen, or torx heads. Step 5: Use a flat tip screwdriver and pop out the sensor. Keep in mind that about one quart of transmission fluid will leak out when you remove it.

Where is the transmission speed sensor on a Dodge Dakota?

The transmission speed sensor on a 1998 Dodge Dakota is located in the overdrive gear case. This sensor actively monitors the speed of the transmission output shaft and relays this information to the powertrain control module, or PCM.

Is the speedometer not working and ABS and brake light stay?

Re: Speedometer not working and abs and brake light stay… You can’t post conmments that contain an email address. An expert who has achieved level 1. An expert whose answer got voted for 2 times. Re: Speedometer not working and abs and brake light stay…

When does the ABS light come on on a Dodge Ram?

This article applies to the Dodge Ram (1994-present). The ABS (Anti-lock Brake System) light should only come on when you turn your key to “On” as a way to check that the light works or when the ABS system is activated. It also stays on when there is an issue with the system.

How to fix ABS and brake light on Dodge Ram?

Dodge Ram abs, airbag, brake light, speedometer fix! – YouTube Dodge Ram abs, airbag, brake light, speedometer fix! If playback doesn’t begin shortly, try restarting your device.

Is there an odometer on a Dodge Ram 1500?

No speedo most of the waning lights in dash, no ac/heat, no odometer. 80 people found this helpful. Problem: I have a 2004 Dodge Ram 1500 5.7 L HEMI. My ABS and Parking Brake lights were illuminated, and my speedometer needle would “bounce”.

Why is my speedometer not working on my Dodge?

My company used to repair body computers (BCM) for Chrysler/Dodge vehicles which contol the warnings you are getting. The car wash could be a major clue. We have seen numerous false intermittent warnings created due to fluid intrusion, such as water, into the BCM assembly.

When did I replace the back ABS sensor?

I have already replaced the front two wheel hubs and ABS sensors, the back ABS sensor (in the diff) and I have also replaced the transmission (last year) along with all sensors on it. All with no change. I dont think it has anything to do with it, but I also replaced the computer last year (due to a different problem).

How do you remove a speed sensor from a car?

Lift the vehicle using the automotive jack, remove the jack stands and lower the vehicle back to the ground. Pull the transmission dipstick from underneath the hood and add in the same amount of Mopar +4 automatic transmission fluid, if any, that spilled out during the installation and removal of the speed sensor.

Where can I get a transmission speed sensor?

Replacement transmission speed sensors are available from most local auto parts stores and licensed Dodge or Chrysler dealerships. Shift the vehicle into park, engage the parking brake and turn off the engine. Open the hood and disconnect the negative battery terminal using a battery terminal wrench.

Where are ABS faults stored on a Dodge Dakota?

Faults are stored in a diagnostic program memory and are accessible with the DRB III scan tool. ABS faults remain in memory until cleared, or until after the vehicle is started approximately 50 times. Stored faults are not erased if the battery is disconnected.

Where is the antilock brake located on a Dodge Dakota?

The Controller Antilock Brake (CAB) is mounted to the Hydraulic Control Unit (HCU) and operates the ABS system. The CAB voltage source is through the ignition switch in the RUN position.

Where is the pump on a Dodge Dakota?

The “pump” is called the HCU (hydraulic control unit) and looks little more than a brake line junction box. It will have TWO solenoid looking thingies on the top and has a white,blue,black and one other color wire running to 4 pin connector directly to the Kelsey Hayes little black abs “computer” it’s on the driver side.

Can a Dakota have both brake and ABS lights on?

I also recently troubleshooted a 1999 dakota (magnum V6) that had both the brake and abs light on steady, but the brakes were still operating normally (without the abs function of course, which is disabled when the ABS light comes on) and the owner couldn’t clear both ABS/Brake lights either.

What are the symptoms of a bad ABS control module?

1. Unresponsive brake pedal. In certain cases, depending on the model of vehicle, when the ABS module fails, the brake pedal may become unresponsive. This is an obvious problem, as an unresponsive brake pedal will not stop a vehicle, or will not be able to do so in an adequately safe manner.

Where is the ABS controller on a Dakota?

The Dakotas have a own unique set of fail codes. It requires a special code reader to access it on it’s own test plug (not the OBDII test plug that is under the dash board). combination/proportioning valve, HCU and ABS controller is located. you may be able to interpret.. indicator as code “13”. Other than that, you would have to visit

What happens when the ABS fails on a car?

In certain cases, depending on the model of vehicle, when the ABS module fails, the brake pedal may become unresponsive. This is an obvious problem, as an unresponsive brake pedal will not stop a vehicle, or will not be able to do so in an adequately safe manner.

Why is there no brake warning light on my Dodge Dakota?

A wheel speed sensor and a problem with the main system. It’s possible that when the brakes were recently done the parking brakes were not properly adjusted. That could illuminate the brake warning light.

What are the codes for an ABS warning light?

If after testing the sensor or if you have scanned the ABS computer and get a trouble code C0035, C0040, C0041, C0045, C0046, C0050, C0051, C1221, C1222, C1223, C1224, C1225, C1226, C1227, C1228 , C1232, C1233, C1234 or C1235 the sensor is either unplugged or it has shorted out and needs replacement.

Do you need code reader for Dodge Dakota?

Most code readers, including the McParts store’s, will only give you those codes. The codes you need include those from the ABS module and you need a code reader or scan tool capable of reading those modules to pull those codes. This time, you’ll need a professional to look at it, someone who has a more sophisticated tech gear than you.

Why does my abs warning light keep flashing?

Most ABS diagnostic codes can be accessed by the ALDL connector much like the engine computer control system. When this warning light flashes or stays on steadily it means the system is disabled.

Why does my Dodge Dakota shift from first to third?

This occurs when I accelerate normally from a stop. For example, after stopping at a stop light. The truck will shift from first to second fine but after that the engine will continue to rev up and the only way to get it to shift into third is to take my foot off of the accelerator and wait for the rpm’s to come down.

Where is the crank position sensor on a Dodge Dakota?

Behing the carburetor on the passenger side and just behind the manifold is a harness leading to what is called the Crank Position Sensor. It basically has the job of telling the engine the position that the crankshaft is in and regulates the firing time accordingly.

Why did my Dodge Dakota engine shut down?

Today I thought I had a bad ground wire from the Battery so I replaced it and after I started the truck and went to the fender to listen to the engine ( about 10 seconds ) The engine died again. We are at a huge loss as to what to do next and thought about the computer. This is a Dodge Dakota fuel injection system and 1992.

When does the brake light and ABS come on?

So, I decided to finally change the rear speed sensor in the diff. The brake light and ABS are still coming on. Here are the details… It does comes on faster in hot weather, and sometimes does not come on untill I hit a bump in the road. Other times, it comes on as soon as I start the truck up.

How do I Turn Off the ABS light on my Dodge Ram?

Disconnect the negative battery terminal. Put the key in the ignition and turn to “on position;” wait 30 seconds. Step on the brake pedal and hold for another 30 seconds (this puts a current drain on the computer system to erase the memory). Release the brake pedal. Remove key from the ignition. Reconnect the negative battery terminal.

Can a transmission speed sensor be removed from a car?

Some speed sensors are internal to the transmission and will require the transmission to be removed from the vehicle before the sensors can be replaced. The most popular service booked by readers of this article is Vehicle Drivetrain Inspection.

Can a bad speed sensor affect shift timing?

Harsh or improper shifting. Without a valid speed signal from these sensors, the PCM will not be able to correctly control the shifting of gears within the transmission. This may cause the transmission to shift roughly or more quickly than normal. It’s also common that a problem with these sensors can impact the shift timing,…

Why is my odometer not working on my Dodge?

The plug connector on Dodge’s has a problem letting moisture/water get into the plug. Use an air hose to blow out the moiture and you can even let it dry out for a bit. Then plug back in, and the problem should be fixed.

Are there any genuine ABS modules for Dodge Dakota?

We offer a full selection of genuine Dodge Dakota ABS Control Modules, engineered specifically to restore factory performance. Please narrow the Anti Lock Brake Control Module results by selecting the vehicle.

What kind of car is a Dodge Dakota?

DODGE SPRINTER / MERCEDES BENZ TRANSPORTER / FREIGHTLINER SPRINTER MODEL YEAR 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 SERVICE REPAIR WORKSHOP MANUAL (PDF) 1995 DODGE DAKOTA SERVICE REPAIR MANUAL DOWNLOAD!!! 2001 DODGE DAKOTA SERVICE REPAIR MANUAL DOWNLOAD!!! 1995 DODGE DAKOTA SERVICE REPAIR MANUAL DOWNLOAD!!!

What is the repair manual for a Dodge Dakota?

Complete list of Dodge Dakota auto service repair manuals: DODGE SPRINTER / MERCEDES BENZ TRANSPORTER / FREIGHTLINER SPRINTER MODEL YEAR 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 SERVICE REPAIR WORKSHOP MANUAL (PDF) 1995 DODGE DAKOTA SERVICE REPAIR MANUAL DOWNLOAD!!!

Is the 1997 Dodge Dakota a work truck?

The 1997 Dodge Dakota has not been tested. Was there ever a time that pickup trucks were just simple workhorses, modern-day buckboards, as stylish as old work boots? There was, but it’s long gone. Successful pickup Read more

What are the symptoms of a bad transmission speed sensor?

Symptoms of a Bad or Failing Transmission Speed Sensor. 1 1. Harsh or Improper Shifting. Without a valid speed signal from these sensors, the PCM will not be able to correctly control the shifting of gears 2 2. Cruise Control Does Not Work. 3 3. Check Engine Light Comes On.

How much does it cost to replace a transmission speed sensor?

Transmission speed sensors tend to cost around the same. Labor varies depending on the engine type, as some sensors are more accessible than others. If your mechanic needs to drop the transmission to replace a transmission sensor, you’re looking at bill around $800-1,000.

Can a check engine light be a bad speed sensor?

But if you have malfunctioning cruise control and a Check Engine light coming on, this is a clear indication of a faulty speed sensor. After all, the engine control unit depends on having valid speed information regarding the engine’s crankshaft.

Are there any problems with my Dodge Dakota?

Tap the to learn more about the most common Dodge Dakota problems. The engine may stall when the engine is warmed up. The AC compressor may seize resulting in loss of cold air from the AC vents. There have been some issues reported with the electric sliding doors. Ignition switch failure may cause the car to stall or fail to start.

When was the last year Dodge Dakota had six bolt wheels?

It was equipped with halogen lights, making 1991 the only model year for a unique front-end for the Dakota. Also debuting on 1991 models were six-bolt wheels (replacing the earlier five-bolt wheels). This was the last year for the Dakota convertible.

What was the problem with my Dodge Dakota?

All fuel seems fine. Got a reading from an OBD1 and egr, crank sensor and a/c clutch came up. Replaced the second crank sensor and she worked fine until this morning, drove 18kms and she shut off again. After sitting for 30 minutes she started right up and made the drive back home with no problems…

Why does my 98 Dodge Dakota not idle?

Had the same problem with my 98 Dakota. It was just the Negative battery end. For some reason when the cable end is not clean and tight it will not idle. 28 people found this helpful. Idle air control valve its on backside of throttle body take out and clean it or replace only 38 bucks at auto my 92 had the same problem

What causes a vibration in a Dodge Dakota?

Let us know in the Values & Prices Paid section! My daughter’s 1990 Dodge Dakota with the 3.9 L engine and automatic transmission with overdrive has developed a vibration. It happens when accelerating while in gear. If the gear selector is set to neutral while rolling, and the engine rpm is speeded up, the vibration doesn’t occur.

What are the specs of a 2003 Dodge Dakota?

A new Stampede Appearance Package will be added during 2003; offered on regular cab and Club Cab Sport models, this option group includes ground-effects side moldings, wheel flares, 16-by-8-inch aluminum wheels and a rear stabilizer bar. All-disc brakes are now standard for the Quad Cab, 4WD and performance-oriented R/T models.

What kind of engine does a 1993 Dodge Dakota have?

1993 Dakota 3.9 4×2 manual. Dies occasionally also, just like ryanodhrty’s (for example coming to a red light in third so i hit the clutch and come to a complete stop and its now dead the weird part is that no lights turn off, its not like it stalls out or anything the engine just shuts down). Haven’t been able to figure it out for 3 years.

What’s the problem with my 2003 Dodge Dakota?

14 people found this helpful. 2003 dodge Dakota, I had the same problem. It was my idler not being controlled properly. Quick free fix. Unhook your battery for a about 10-20 seconds, let everything reset and he idle right again.

What happens when the transmission speed sensor is lost?

If the signals are lost from the transmission speed sensors, the PCM will set a DTC and illuminate the Check Engine Light on the vehicle dashboard. It also can indicate an increase in tailpipe emissions surpassing acceptable limits for environmental contaminants from motor vehicles.

Is there a Dodge Dakota transmission on eBay?

Here are some options: New transmission: Although you can certainly opt to order an entire brand-new transmission from Dodge, the amount of money you will be out may be exorbitant. There are myriad of new transmission parts available on eBay, but rarely is there a new entire transmission.

What kind of automatic transmission does a Dodge Durango have?

automatic transmission rebuilt Part Number Trans. Model Min Year Max Year Application 4002411 A4LD 1992 Dakota 4X4 4003008 A500 1996 1997 Dakota 4X4 4002483A A500 1992 1993 Dakota 4X4 4003240 A500 1998 1999 Dakota Durango 4X4

What kind of engine does a 1996 Dodge Dakota have?

Description: Used 1997 Dodge Dakota Sport with 3500lb Towing Capacity, Extended Cab. Slt Plus Quick-Order Pkg 4-Speed Automatic Transmission W/Od 3.9L (239) Mpi V6 “Magnum” Engine Powertrain This vehicle includes a Money-Back Guarantee* and passed our precise inspection process. Best of all the price you see is the price you pay. No haggling.

What kind of car is a 1999 Dodge Dakota?

Description: Used 1999 Dodge Dakota SLT with Extended Cab. Vehicle may have road chips, scratches, wheel scuffs, etc. Depending on the age/miles of the vehicle normal wear and tear should be anticipated. We may or may not have all the keys and floor mats.

Where can I buy a 1992 Dodge Dakota?

Stop By Today Come in for a quick visit at Sid Dillon Ford Wahoo, 257 West A St, Wahoo, NE 68066 to claim your Dodge Dakota! Thank you for choosing to visit siddillon.com in Wahoo, NebraskaSid Dillon Ford in Wahoo is your local Ford Dealer. We are located close to Lincoln, Omaha, Elkhorn, Gretna, and Millard.

When does a bad ABS wheel speed sensor fail?

When the ABS wheel speed sensor fails, the ABS light is probably one of the first sign your will notice of all bad ABS wheel speed sensor symptoms. At first, it might simply cause the ABS warning light to come on. However, when the other systems stop functioning properly, you might also see the traction and stability control warning lights too.

What causes the ABS speedometer to stop registering?

However, when the other systems stop functioning properly, you might also see the traction and stability control warning lights too. In rare cases, defective ABS wheel speed sensors can cause the speedometer to stop registering. RELATED: What does the ABS light mean & What Causes it?

When does the brake light and ABS light come on?

The brake light and (abs)light comes on after a few mn and stays on. ken The ECU (Engine computer) needs to know the roadspeed of the vehicle to determine the best idle speed and for the ABS to work properly. Since your speedometer is not working… this means that the ECU does not know the speed of the vehicle.

What happens when the ABS system is not working?

The sensors detect wheel speed, and will send a message to the ABS module to rapidly pump the brakes when it is detected that the vehicle is skidding or has lost traction. When the ABS system is not functioning then loss of traction, skidding, and hydroplaning are far more likely to occur under heavy braking conditions.

What happens if your speedometer is not working?

Since your speedometer is not working… this means that the ECU does not know the speed of the vehicle. (It is the ECU which drives the speedometer and feeds roadspeed signal into the ABS computer.) There is a roadspeed sensor which feeds a signal into the ECU.

What to do if speedometer needle jumps up and down?

Reach around behind the speedometer or remove the instrument cluster to gain access and disconnect the speedometer cable from the speedometer. Pull out the inner cable, clean and inspect it, coat it with light grease, or M/C cable lube and put it back together. That should cure it… The speedo cable for those old cars is like a spring.

How can I tell if my speedometer is not working?

Whether you have a digital or manual speedometer, if it’s not displaying accurate information, it doesn’t really help you. One of the biggest signs your speedometer sensor is not working properly is the speedometer will display inaccurate readings or the needle or digital numbers will not move at all on the speedometer display.

Where is the speedometer sensor located? The speedometer sensor is located in the transmission of your vehicle and is designed to register the driveshaft’s rotational speed. The sensor delivers this information through the speedometer cable and to the vehicle’s computer, which converts electrical pulses into a numerical speed.

Why are the brake lights on my Dodge Ram 1500?

The problem started with the ABS & brake lights on the dash coming on. The ABS system failed and the speedometer would only work after a speed of about 30 MPH. It eventually failed totally and as a result the cruse control and odometer no longer worked. At first I replaced the vehicle speed sensor on the Transmission housing. No luck with that.

How do you change ABS on a Dodge Ram?

Before you replace this unit, bleed the old ABS pump as you would brakes by loosening the output brake line, to the rear wheels, on the pump after someone pumps and holds the brake down as you do when bleeding brake lines. This may do the trick as air can affect the pump as it does the brakes.

Why is my odometer not working on my Dodge Ram 1500?

My speedo was possessed, fluctuating while parked and the odometer was advancing, also while parked. The ABS, Check engine, and Brake lights were all on. I first bought a new CPU. wasn’t the problem and took it back, tried a new Gauge cluster from a friends truck, still nothing.

Where are the brake lights on a Dodge Dakota?

Backing out of the shop, stopping, turning around, down the driveway 50yds and stopping at the road…the lights stay off, even though I just used the brakes three times at least. Get on the road and hit 30mph and they go on. The two fuses, one in the fuse block by the drivers door and the other (ABS) fuse in the Power distribution box test good.

Are there any leaks in the front rotors of a Dodge Dakota?

No leaks of any lines, calipers, or cylinders. Front rotors are not scored from a sticky caliper, they do have a little minor rusting but because it has been idle for a few months. I have the same year and drive train in my Dakota.

Place a drain pan beneath the sensor to catch any transmission fluid that may drip out. Remove the sensor and O-ring seal using a metric socket and a ratchet. Install a new O-ring seal on to the new speed sensor. Install the sensor into the transmission using a ratchet and metric socket. Tighten it to 20 foot-pounds using a torque wrench.

How do you install a sensor in a transmission?

Install the sensor into the transmission using a ratchet and metric socket. Tighten it to 20 foot-pounds using a torque wrench. Reconnect the sensor’s electrical connector and exit from underneath the vehicle. Lift the vehicle using the automotive jack, remove the jack stands and lower the vehicle back to the ground.

How to repair the ABS and speed sensor in a Dodge Dakota?