How to permanently disable GM pass lock system?

•Disable Pass Lock system to prevent from being stranded in the future. This tutorial varies depending if the ignition is located: If your ignition is located in the dash then you will be removing the panels on the passenger underside (toe board) of the dash.

What does it mean when your ignition key does not turn?

If it will not move, or moves only very slightly, it is likely locked. A locked steering wheel will not allow the ignition to engage. When you move the wheel back and forth, you will feel it stop abruptly as it comes into contact with the steering wheel lock.

Why does my car lock up without a key?

At times the steering wheel of the car locks up and you are unable to turn the ignition key either. The problem may occur due to many reasons. In situations where there is no help available nearby, you must know how to unlock steering wheel without key on your own.

How can I bypass the steering wheel lock?

Here are three alternatives under this category for how to bypass steering wheel lock. 1. Try inserting the key Try inserting the key into ignition and turn the key and the steering wheel left and right all at once. Ensure that it is simultaneous. If the locking is accidental in nature, this trick will fix it with a click.

What should I do if my ignition key won’t turn?

Spray the canned air into the key hole in short spurts. It should only take a few short sprays to clean out any debris. Do not spray the entire can into the key hole. The extreme cold could result in damage to the ignition cylinder. Wear eye protection when using canned air to clean the key hole to ensure no debris gets into your eyes.

What happens if you wiggle the ignition key?

Be careful not to apply too much pressure. Wiggling the key can make the key contact the pins from a different angle, which may allow you start the vehicle. If wiggling the key works, it means the teeth on the key are too worn to properly engage the pins. Replace the key as soon as possible if this works before the key stops working entirely.

Is there a way to bypass PassLock 2?

The easiest way to bypass the Passlock 2 system is to place a resistor between the passlock sensing wire and the ground reference wire. To find these wires, look for three wires that at some point are wrapped together, coming from the ignition barrel. Usually, they are orange/black, red/white, and black.

How to bypass vats, Passkey and PassLock security systems in GM?

It can be VATS, Passkey or Passlock anti theft system that is going bad causing your issue. I am going to share a secrete with you on how you can bypass these systems with very little effort. This is a really unique security system bypass kit that you can use to override your current factory theft system on your GM vehicle.

Where is the transmitter on a GM Passkey?

As the driver moves the key towards the lock cylinder, a transmitter sends an interrogation signal to the transponder key. The transmitter is located in a ring surrounding the outer edge of the lock cylinder. The transponder receives the interrogation signal and responds with a coded message.

How often does a GM PassLock light flash?

You need a scan tool. If the signal is not correct, the PCM disables the injector and the starter and flashes the light once per second. If an illegitimate key is used or a system problem exists, the light flashes twice per second. This system allows starter operation, then kills the injectors 1-2 seconds after startup.

When was the GM passkey security system introduced?

Back in 1986 the GM Passkey security systems, also known as immobilizers, were introduced. In doing so, an expensive time-bomb was implanted in each and every one of the affected vehicles.

How do you disable the passkey on a GM car?

You can swiftly disable the passkey anti-theft system and get your GM started by performing the “relearn” procedure, which disables the passkey by resetting it. Insert your GM key into the ignition, attempt to start the car, and let it stall.

When to remove GM vats Passkey security system?

Seriously! Bypass and remove GM VATS PassKey and PassLock systems even if you still don’t have problems with them. If your car is more than 6 years old, it is only a matter of time before the worst happens – and the problem is that you never know when it’s going to happen… and where!

How to reset PassLock reset system on Chevy?

1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine.

Why does my Gm key not turn in?

The GM (Buick, Cadillac, Chevy, GMC, Hummer, Oldsmobile, Pontiac) ignitions tend to fail because of wear from inserting the key at a slight angle. This is the same for the Chrysler vehicles (Chrysler, Dodge, Eagle, Jeep, Plymouth).

How do I Turn Off the PassLock security light?

When did General Motors introduce the PassLock ignition lock?

For the 1995-1/2 model year, General Motors introduced PASSLock, the first ignition lock equipped with a magnet mounted into the ignition lock cylinder and a corresponding Hall-effect sensor mounted into the housing assembly.

How long does it take to turn off a GM security light?

Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2. Turn the ignition switch to the “OFF” position for 30 seconds. 3.

How to permanently disable GM pass lock system?