How to permanently disable and remove GM security systems?

GM Security Systems are killing cars all over North America and the only final solution is to disable and remove them permanently. This is what NEWROCKIES Inc is all about.

Can a GM security bypass kit be installed?

This GM security Bypass kit will work for several GM, Oldsmobile, Chevy, Pontiac or even Buick vehicles on the street today. I was surprised to see how easy it was to install with very little effort.

Can a GM security system be moved to another car?

Newrockies inc proudly manufactures its modules with top quality electronic components. No more risks of remaining on the road. Universal. The same module works with over 100 different GM and Isuzu cars – you can even move it on your next car! Trusted.

How to reset PassLock reset system on Chevy?

1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine.

GM Security Systems are killing cars all over North America and the only final solution is to disable and remove them permanently. This is what NEWROCKIES Inc is all about.

This GM security Bypass kit will work for several GM, Oldsmobile, Chevy, Pontiac or even Buick vehicles on the street today. I was surprised to see how easy it was to install with very little effort.

How do I Turn Off the PassLock security light?

How can I Reset my GM theft deterrent alarm?

If anything else is open, the alarm will not be reset. Close the door and wait for the security light to stop flashing from inside the car. Another option is to close the doors first, and then press the “Lock” button on the keyless remote. This will also pre-arm the theft-deterrent alarm system.

What kind of theft deterrent does General Motors use?

General Motors is an automobile manufacturer that owns Chevrolet, Buick, GMC and Cadillac. Current automobiles use a theft-deterrent alarm system to prevent break-ins. The horn will sound while the headlights flash on and off.

Why is the security light on my truck not working?

There’s a possible SECURITY related wiring glitch with 98-01 trucks. A service bulletin was issued – but a correctly installed resistor should have bypassed the possible wiring problem. (PM email address if you want copy of SB). Did you try relearn after installing 2.2K resistor between orange/black and yellow wires attached to BCM? 1.

What should resistance be for VSS speed sensor?

Disengage the wiring harness connector from the VSS. Using a Digital Volt-Ohmmeter (DVOM), measure the resistance (ohmmeter function) between the sensor terminals. If the resistance is 190–250 ohms, the sensor is okay. Vehicle Speed Sensor Replacement REMOVAL & INSTALLATION(older models)

How do you install a VSS in a car?

Ensure that the O-ring is properly seated in the VSS housing. For ease of assembly, engage the wiring harness connector to the VSS, then insert the VSS into the transmission assembly. Install and tighten the VSS hold-down bolt to 62–88 inch lbs. (7–10 Nm). Lower the vehicle and remove the wheel blocks.

What kind of security system does a GM Truck have?

Here is a list of GM vehicles that have VATS, Passkey or Passlock security system built in from the factory. Trucks GMC/Chevy 1998-2006 S10/T10/Sonoma /Blazer/Jimmy 1998-2007 Suburban/Avalanche /Tahoe/Yukon 1998-2010 Sierra/Silverado 2004-2010 Colorado/Canyon 2002-2008 Trailblazer 2003-2006 SSR

How to bypass factory theft on a GM vehicle?

This is a really unique security system bypass kit that you can use to override your current factory theft system on your GM vehicle. You can get this kit from New Rockies.com . I came across this site surfing the net when I was having a similar issue on a GM vehicle.

What’s the name of the security system on a Chevy?

[1] Well, Passlock should be called the Great Immobilizer because not only does it stop thieves with no keys, it also stops owners with the right keys. GM introduced many security systems – VATS, Passkey, Passlock, but if your GM has a key without a chip in it, chances are it’s passlock.

How to reset the security for a 1996 GMC?

Sanstrom has undergone advanced automotive training at the Dunwoody College of Technology, holds an Associate of Arts in general studies from Century College and has more than 10 years of experience in all aspects of automotive repair and diagnosis. How to Reset the Security for a 1996 …

How do you reset the ECM on a Chevy truck?

Returning the ECM to its factory state may be necessary to troubleshoot or resolve a number of problems. Remove the nut from the negative battery cable using a socket set or wrench. Slide the cable off of the battery and set it aside. Turn the headlight switch to the “On” position to drain the ECM of any remaining power.

How long does it take to turn off a GM security light?

Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2. Turn the ignition switch to the “OFF” position for 30 seconds. 3.

How to bypass vats, Passkey and PassLock security systems in GM?

It can be VATS, Passkey or Passlock anti theft system that is going bad causing your issue. I am going to share a secrete with you on how you can bypass these systems with very little effort. This is a really unique security system bypass kit that you can use to override your current factory theft system on your GM vehicle.

Is there a way to bypass GM PassLock?

At NEWROCKIES Inc., we’ve designed our PRO Bypass Module with the specific purpose of bypassing faulty GM VATS, Passkey and Passlock security systems IN FULL.

What to do when your car alarm stops working?

However, there are some cars that aren’t accessible because the door locks are disabled when the alarm sounds. If that happens with your car, try putting the key in either the driver’s or the passenger’s door, turning it and then waiting a few seconds. The alarm usually will stop.

Is it possible to disable a car alarm permanently?

If you’re wondering can you disable a car alarm permanently, the answer is yes, of course. There are simple instructions if you want to know how to disarm a car alarm completely. You should just unlock the door, start the car, remove the fuse, or detach the car battery.

How do you reset an aftermarket car alarm?

Almost all alarms, both factory installed and aftermarket systems, will shut off and reset when the car is started. Step 3: Use your key to unlock the driver’s door. This will usually turn off and reset the alarm. In the event that the driver’s side door is already unlocked, lock the door and then unlock it again. Step 4: Pull the fuse.

Why does my PassLock security light keep going off?

After turning the ignition off for the third time and waiting for twenty seconds, the engine should start and run. If it doesn’t, there may still be something wrong with the system. After the learn procedure is completed and the engine is running, the security light may stay on steady for a few minutes and then go off—this is normal.

What happens when the PassLock system detects a fault?

When the system detects a fault, the warning light will illuminate or a message will be displayed on the DIC, depending on the model. If a fault occurs while driving, the engine may or may not start after turning the ignition off. If a fault occurs when trying to start the vehicle, it probably won’t start.

Can a red / green wire disarm a factory alarm?

This RED / GREEN wire is the SAME wire I told you to Ground. IF grounding the RED / GREEN wire does NOT DisArm the Factory Alarm, then there is a problem with the Factory Alarm. .

How does the security system work on a Harley Davidson?

The security system on the Harley Davidson Touring allows you to use your key fob to activate it, which prevents you from starting the bike until you deactivate it with your key fob again. Sometimes, you can get stuck and can’t deactivate the security system, or you lost the key fob and want to override it.

How do you disable the factory security system?

To completely disable the factory security system, simply disconnect the harness that powers it. A green, two-pin plug is located by the hood latch, and it is attached to the grille by six screws. Pull the latch on the plug and slide the two-wire bundle out.

How do I deactivate the security system on my car?

Then hit the unlock button on the fob twice this should deactivate the security system which should be accompanied by exterior lights flashing or an audible horn beep. Each of these steps should be followed by the cancellation of the security light.

Is there a way to disengage anti theft system?

This is why; disabling anti theft system becomes essential. To start with, check the anti theft light on your car’s dashboard, it would be either a blue or a red light. Next, insert your key to power the engine, and leave the key there for at least 10-15 minutes.

How to disengage anti theft system on Ford F150?

Last of all, car owners need to press the power door unlock button three more times, then turn the key back on in order to bypass the anti theft on a 2000 Ford f150. What does it mean when the anti theft light is blinking?

What is the yellow light on a GM starter interrupt?

In this article, we are concentrating on factory-installed GM starter interrupt systems. This type of anti-theft system is designed to prevent the vehicle from starting unless the correct ignition key is used. These systems used a dash-mounted “security” or “theft” light which can be yellow or red in color.

How to turn off GM PassLock security Telltale?

Here it is in it’s entirity. Turn ON the ignition, with the engine OFF. Attempt to start the engine, then release the key to ON (vehicle will not start). Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF. Turn OFF the ignition, and wait 5 seconds .

Why does my Chevy Silverado have intermittent starting problems?

It started with intermittent “NO start” problems along with a host of other electrical problems around 16,000 miles. Once I thought I fixed the problem while beating on the steering column, however it turned out to just be a coincidence, as I had also rolled the truck down hill into the sunlight (heating from sun increased cab temperature).

Can You disable the PassLock on a GM car?

The following instructions will allow you to disable the PassLock security in quite a few GM Vehicles. •This will allow you to install a remote starter and not have to purchase a bypass. •Avoid Costly repairs for an already broken PassLock System.

Why does my car alarm keep going off?

It is possible that the key fob or alarm remote has failed and is not sending a proper signal to your vehicleâ€™s alarm system. When this happens, your vehicleâ€™s alarm may inadvertently end up going off without you wanting it to. Step 1: Consult your manual.

When do I need to disable my car alarm?

If your alarm is causing a constant distraction, going off often and spontaneously, you may want to disable the alarm completely. Be mindful however, that if you disable the alarm, your vehicle will have one less safety feature. You should consult a mechanic before deciding to completely disable your alarm.

How can I Reset my GM car alarm?

After deactivating it, you can reset the alarm to ensure that your GM vehicle security system is set correctly. Use your GM keyless remote to unlock the doors by pressing the “Unlock” button.

How to permanently disable and remove GM security systems?