How to fix Chevy GMC Truck heater blend door?

1999 – 2004? Chevy GMC Truck Heater Blend Door Stuck Easy Fix How-to – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.

What causes a car door to not close?

If the latch mechanisms gets tripped while your door is open you may not be able to close the door if your car can’t automatically reset it when the handle is pulled. In this video I show a few different car doors and how the latches work. Hope this helped you out!!! Loading…

What’s the best way to lock a car door?

Find the hole or gap that is meant to catch on the hasp of the car door. Insert a key, pen, or other thin and long tool into the gap. Flick/push the latch toward your car in a semi-upward motion. Close your door. Once the door is able to be shut, it would be advisable to not lock your door again until the issue has been resolved.

Where is the temperature actuator on a car?

Here is a typical right side temperature actuator used for dual climate controls (also temperature for signal mode units). This actuator hangs below the box which is one of the easier units to replace. Begin by using a small screwdriver to release the wiring safety clip on the harness for the actuator.

How to replace air temperature control 00-13 Chevy?

Once you remove those bolts, just reach in, kind of pull it down and out of the way. The actuator is right down here. It’s held in with two bolts, they’re 7/32s. One of them is right over here. The other one’s on the opposite side.

What do I need to replace car door actuator?

You will need a tool set including an 5.5 mm socket for Chevy, GMC, Cadillac, Ford and Lincoln vehicles. Using a small socket and ratchet remove the mounting bolts that hold the under dash plastic cover on the passenger side. These screws can be in obscure places so look around for them.

How to replace blend door actuator in Chevy Silverado?

1. Turn OFF the ignition. 2. Remove the battery positive voltage circuit fuse of the HVAC Control Module. – The scan tool must be disconnected from the vehicle to properly perform the calibration procedure. If a scan tool is connected before this procedure is completed, then new calibration values will not be stored.

Is there a problem with my Blender actuator?

Knocking: This is an unusual symptom, but if you’re experiencing this, it’s almost definitely a problem with your blender actuator. When you start the car, or just the AC system, and notice a knocking sound like someone tapping on your door, that is indicative of a problem with the blend door actuator.

What to do if your blend door blower is stuck?

If the door is stuck the heater plenum with need to be removed and the problem resolved before installing the new unit. To test the blend door operation and too double check that you are changing the correct actuator motor turn the blower motor on and work the door in each way.

How to replace an automotive blend door actuator?

Before installing the new actuator it’s a good idea to manually turn the blend door in both directions to ensure it is not stuck which will cause the new actuator to fail. Grasp the door pivot and move it back and forth to its full travel, it should move freely.

How do you replace a blend door on a Chevy Silverado?

For those interested in replacing the driver side actuator, refer to the following instructions: The driver-side blend door is accessed by removing the IP instrumental panel. Once the panel is off, simply loosen the actuator mounting screws and disconnect it from the HVAC system. Then replace the unit.

Can a heater be removed from a blend door?

Where is the AC delete cover on a 1967 Chevy truck?

Reproduction heater box seal for 1967-72 truck models, which mounts between the heater box and firewall. Produced in rubber for proper fit and function. This AC delete cover for allows you to remove your existing air conditioning evaporator unit while maintaining the heater functions.

Where is the heater seal on a 1967 Chevy truck?

Reproduction heater box seal for 1967-72 truck models, which mounts between the heater box and firewall. Produced in rubber for proper fit and function. This item connects the heater box to the distribution case assembly for 1967-72 models. Replace your missing or broken plenum with this quality reproduction.

What does the air door actuator on a Chevy do?

The Air Door Actuator controls the flow and temperature of air in your vehicle’s AC system. This part commonly fails on Chevrolet, Chevy, Buick, Cadillac, Pontiac, Oldsmobile or GMC models leading incorrect air flow or temperatures inside your vehicle.

How to replace a HVAC blend door actuator?

It was an exact structural match to the original I removed (GM part #16177412 / B2852294A). JUST REMEMBER TO INSTALL THE PART *BEFORE* PLUGGING THE WIRING HARNESS IN (DO NOT TEST ANY ACTUATOR UN-INSTALLED!)